• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.22 no.4
• /
• pp.761-770
• /
• 1997

Narrowband signals can be treated like a single tone interference at the receiver which demodulates wideband signals spectrum overlaid at the same frequency band. In this paper, the single tone interference is effectively suppressed by the use of a multicarrier DPSK direct-sequence(DS) spread spectrum(SS) with maximal-ratio(MR) combining instead of notch filter, which is hard to implement. A noncoherent DPSK system is considered because it is more realizable and does not require any complicate phase tracking, compared with a single carrier system subject to a constraint system bandwidth, and their performance comparisons are validated through simulation. We also propose a suboptimal-ratio(SR) combining which yields uniform and tight low bound on the performance of the MR combining, and then system parameters re optimized by theoretically evaluating the low bound, since an exact analysis appears intractable.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2013.08a
• /
• pp.115.2-115.2
• /
• 2013

10 Gev의 빔에너지를 가지는 4세대 방사광 가속기의 hard X-ray구간에는 약 200 m의 언듈레이터 홀이 건설 중이며, 내부에는 길이 5 m의 언듈레이터와 1m의 언듈레이터 사이구간이 연속적으로 배치되어 있다. 이 구간에는 언듈레이터를 비롯하여 phase shifter, quadrupole, BPM 등이 설치되는 진공용기가 있으며, 이 진공용기는 최적화된 환경을 제공하기 위해서 매우 얇고 긴 형태로 제작되며 각 구간마다 빔손실이 발생하지 않도록 설계가 되어야 한다. 여기에서는 현재 실험 및 설계 중인 언듈레이터 챔버와 사이구간의 진공시스템에 대하여 소개하고, 현재까지 수행한 결과와 앞으로의 진행방향에 대해 다루고자 한다.

• Proceedings of the Korean Society for Technology of Plasticity Conference
• /
• 2008.05a
• /
• pp.431-434
• /
• 2008

Effects of microstructure on the toughness of low carbon HSLA steels were investigated. Nickel decreased the ferrite-austenite transformation temperature, resulted in increase of the fraction of bainitic ferrite. However, it was decreased with increasing deformation amount at austenite region. Since fine austenite grains formed by dynamic recrystallization under large strain transformed to acicular ferrite or granular bainite rather than bainitic ferrite. The effective grain size, thus, was decreased by deformation and it resulted in lower ductile-brittle transition temperature (DBTT). The bainitic ferrite was thought to inhibit the fracture crack initiation and to delay the crack propagation by its high dislocation density and hard interlath $2^{nd}$ phase constituents, respectively. Thus, DBTT was also decreased by Ni addition in low carbon HSLA steels.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2005.10a
• /
• pp.94-99
• /
• 2005

Though the technology on the ultra-precise machining has been developed intensively, the high speed and high precision for large machining range is still very hard to achieve. The linear motor system fur the universal machining center is proper fur high speed and high precision, but it has drawback of sensitivity to disturbance. In this research, two degrees of freedom controller based on the zero phase error tracking controller (ZPETC) and disturbance observer are proposed to improve the tracking performance and dynamic stiffness of linear motor system. The proposed controller is verified in simulations and experiments on a nano-positioner system, and the experimental result shows that the tracking performance improved. In addition, the PID optimization method is proposed for the commercialized controller such as the PMAC based system. The tracking as well as impedance is included in the cost function of optimization.

• Journal of the Korean Magnetics Society
• /
• v.5 no.5
• /
• pp.636-640
• /
• 1995

FeN thin films were deposited on glass by RF diode reactive sputtering. The films were annealed in the air and in vacuum. The film annealed in the air showed sharp decrease of saturation magnetization and change of easy axis direction to hard axis direction and vice versa after $300^{\circ}C$ anneal. The coercivity decreased down to 0.5 Oe after $400^{\circ}C$ anneal. After $450^{\circ}C$ anneal, the film showed ${\varepsilon}-Fe_{2-3}N$ phase. The films annealed in vacuum showed coercivity increase after $300^{\circ}C$ anneal for the film deposited with initial substrate temperature of $35^{\circ}C$ and after $400^{\circ}C$ anneal for the film deposited with initial substrate temperatue of $170^{\circ}C$. These films showed $Fe_{16}N_{2}$ X-ray peaks after $450^{\circ}C$ anneal.

• Journal of the Korean Ceramic Society
• /
• v.35 no.9
• /
• pp.939-944
• /
• 1998

The formation microstructure and properties of novel ceramic composite materials by active filler con-trolled polymer pyrolysis were investigated. Polymethlsiloxane filled with W is of particular interested be-cause of the formation of ceramic bonded hard materials (WC-$W_{2}C$-$S_{1}OC$) for wear resistant applications. Highly metal-filled polymer suspensions were prepared and their conversion to ceramic composites by an-nealing in $N_{2}C$ atmosphere at 1000-$1600^{\circ}C$ were studied. Dimensional change porosity and phase distribution (filler network) were analyzed and correlated to the resulting material properties. Microcrystalline com-posites with the filler reaction products embedded to the resulting material properties. Microcrystalline com-posites with the filler reaction products embedded in a silicon oxycarbide glass matrix were produced. De-pending on the pyrolysis conditions ceramic composites with a density up to 95 TD% a hardness of 7-8.8GPa Yong's modulus of 220-230 GPa a fracture toughness of 6-6.8$MPam^{1/2}$ and a flexual strength of 380-470 MPa were obtained.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.38 no.6
• /
• pp.629-636
• /
• 2014

For surface modification, bulk metallic glass coatings were fabricated using metallic glass powder and a mixture of a self-fluxing alloy or/and hard metal alloys with a heat-resisting property using a high velocity oxy-fuel coating thermal spraying process. Microstructural analyses and mechanical tests were carried out using X-ray diffraction, a scanning electron microscope, an atomic force microscope, a three-dimensional optical profiler, and nanoindenation. As a result, the monolithic metallic glass coating was found to consist of solid particle and lamellae regions that included many pores. Second phase-reinforced composite coatings with a self-fluxing alloy or/and hard metal alloy additives were employed with in-situ $Cr_2Ni_3$ precipitate or/and ex-situ WC particles in an amorphous matrix. The mechanical behaviors of the solid particles and lamella regions showed large hardness and elastic modulus differences. The mechanical properties of the particle regions in the metallic glass composite coatings were superior to those of the lamellae regions in the monolithic metallic glass coatings, but indicated similar trends in matrix region of all the coating layers.

• Journal of KIISE:Information Networking
• /
• v.32 no.5
• /
• pp.633-640
• /
• 2005

This paper proposes and analyzes a message scheduling scheme and corresponding bandwidth allocation method for the hard real-time communication on dual standard 802.11 Wireless LANs. By making the superframeof one network precede that of the other by half, the dual network architecture can minimize the effect of deferred beacon and reduce the worst case waiting timeby half. The effect of deferred beacon is formalized and directly considered to decide the polling schedule of PCF phase. Simulation results executed via ns-2 show that the proposed scheme can improve the schedulability by 3$36\%$ for real-time messages and give $9\%$ more bandwidth to non-real-time messages for the given stream sets, compared with the network whose bandwidth is just doubled with the same MAC.

• The Transactions of the Korean Institute of Power Electronics
• /
• v.5 no.4
• /
• pp.309-317
• /
• 2000

This paper presents the switching angle and voltage to maximize torque/efficiency and minimize torque ripple in the 4-phase 6-poles Switched Reluctance Motor(SRM). SRM drive has high saturation and nonlinear characteristics of inductance. So we cannot hard to find optimal condition by using analytic method. Therefore it is hard to find the operating the switching angle and voltage through the approximated analysis and computer simulation by using SIMULINK according to the speed and torque required by load. From the results, we can say that the optimum average voltage is determined by the load only and the speed is determined by the optimum turn-on/off angle only. And the maximum efficiency and minimum torque ripple depend on switching angle, not on voltage. And then one-chip microcontroller controls the switching angle and voltage of an asymmetrical inverter in the SRM driver. This drive method, which is expect that the driving methods, which are maximizing torque/efficiency and minimizing torque ripple, will be suitable for the electric vehicle, the industrial application and household appliances.

• Journal of Powder Materials
• /
• v.14 no.2 s.61
• /
• pp.132-139
• /
• 2007

In the Ti(CN)-Co/Ni cermet, WC is an effective additive for increasing sinterability and mechanical properties such as toughness and hardness. In this work, WC, (WTi)C and (WTi)(CN) were used as the source of WC and their effects were investigated in the respect of microstructural evolution and mechanical properties. Regardless of the kinds of WC sources, the hard phase with dark core and bright rim structure was observed in the Ti(CN)-Co/Ni cermet under the incorporation of relatively small amount of WC. However, hard phases with bright core began to appear and their frequency increased with the increase of all kinds of WC source addition. The ratio of bright core to dark one in the (TiW)(CN)-Co/Ni cermet was greatest under the incorporation of (WTi)C compared at the same equivalent amount of WC. The mechanical properties were improved with the addition of WC irrespective of the kinds of sources, but the addition of (WTi)(CN) was less effective for the increase of fracture toughness.