• Korean Journal of Optics and Photonics
• /
• v.5 no.2
• /
• pp.278-285
• /
• 1994

We investigated the spectral characteristics for temperature and driving current change in visible laser diode. As a result of spectrum analysis, the ratio of frequency change for temperature and driving current change were about $33 GHz/^{\circ}C$, 6.6 GHz/mA in the region which was not mode hopping range. Compared to the sharp mode hopping in the near IR single mode AlGaAs lasers, the visible laser diode showed relatively broad multimode operation in the mode hopping region. We performed the experiment of injection-locking characteristics analysis for visible laser diode. Locking half bandwidth(LHBW) was measured 0~5.0 GHz for $0~25\muW$ input power and it was dependent on the input power. Also, LHBW for polarization angle was dependent on the difference of polarization angle between master laser and slave laser. The phase change of injection-locked output beam of the slave laser diode as a function of the drive current was measured in the interferometer which was composed of master laser and slave laser. The ratio of phase change with the slope of 5.0~1.3 rad/mA was obtained within injection-locking range for the change of $2~25\muW$ input power. power.

• Current Optics and Photonics
• /
• v.3 no.6
• /
• pp.583-589
• /
• 2019

We report experimental results on 940-nm 350-mW AlGaAs/InGaAs transverse single-mode laser diodes (LDs) adopting graded-index separate confinement heterostructures (GRIN-SCH) and p,n-clad asymmetric structures, with improved temperature and small-divergence beam characteristics under high-output-power operation, for a three-dimensional (3D) motion-recognition sensor. The GRIN-SCH design provides good carrier confinement and prevents current leakage by adding a grading layer between cladding and waveguide layers. The asymmetric design, which differs in refractive-index distribution of p-n cladding layers, reduces the divergence angle at high-power operation and widens the transverse mode distribution to decrease the power density around emission facets. At an optical power of 350 mW under continuous-wave (CW) operation, Gaussian narrow far-field patterns (FFP) are measured with the full width at half maximum vertical divergence angle to be 18 degrees. A threshold current (I_th) of 65 mA, slope efficiency (SE) of 0.98 mW/mA, and operating current (I_op) of 400 mA are obtained at room temperature. Also, we could achieve catastrophic optical damage (COD) of 850 mW and long-term reliability of 60℃ with a TO-56 package.

• Korean Journal of Optics and Photonics
• /
• v.28 no.6
• /
• pp.361-365
• /
• 2017

In this paper, we demonstrate a facile fabrication technique for a periodically aligned metal nanoparticle array, for a narrow-band plasmonic absorber. The metal nanoparticles are fabricated by e-beam evaporation and heat treatment processes on top of a periodic aluminum groove template. The plasmonic absorber is constructed with the transferred metal nanoparticle array, sputtered 33-nm-thick $Al_2O_3$, and 200-nm-thick metal reflector layers on silicon substrate. 46-nm-diameter and 76-nm-lattice metal-nanoparticle-array-based plasmonic absorber has performed as a narrow-band absorber with a central wavelength of 572 nm and full width at half maximum (FWHM) of 109.9 nm.

• Journal of Sensor Science and Technology
• /
• v.12 no.6
• /
• pp.282-288
• /
• 2003

We report the growth of HgCdTe by metal organic vapor phase epitaxy (MOVPE), using (211)B CdTe/Si substrates grown by molecular beam epitaxy (MBE). The surface morphology of these films is very smooth with hillock free. The etch pit densities (EPD) and full widths at half maximum (FWHM) of x-ray rocking curves exhibited that the crystalline quality of HgCdTe epilayer on MBE grown CdTe/Si was improved compare to HgCdTe on GaAs substrate. The Hall parameters of undoped HgCdTe layers on CdTe/Si showed n-type behavior with carrier concentration of $8{\times}10^{14}/cm^3$ at 77K. But HgCdTe on GaAs showed p-type conductivity due to in corporation of p-type impurities during GaAs substrate preparation. It is thought that these results are applicable for large area HgCdTe forcal plane arrays of $1024{\times}1024$ format and beyound.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.18 no.8
• /
• pp.913-921
• /
• 2007

In this paper, we propose a novel small antenna for direction finding applications. The proposed antenna employs a skirt type disk to eliminate the radiation null on the broad-side direction in the high frequency range. Additionally, the multi-section matching stub is used for impedance matching in the low frequency range, The size of the proposed antenna is reduced as a half of the 60cm dipole which has a same resonance frequency of 200MHz. The antenna maintains a donut shape radiation pattern with a broad beam width for a wide range of frequency while the 60cm dipole shows radiation nulls on the broad-side direction and the high side-lobe level from 700MHz to 1,300MHz.

• Transactions of the Korean Society of Mechanical Engineers
• /
• v.17 no.6
• /
• pp.1381-1388
• /
• 1993

This paper presents a method for the simultaneous optimal design of structural and control systems. Sensitivities of performance index with respect to structural design variables are analyzed. The structural design variables are optimized to minimize the performance index by use of conjugate gradient method. The method is applied to a half model of an active vehicle suspension system with elastic body moving on a randomly profiled road. The suspension control force of an optimally controlled system in the presence of measurement errors are calculated by use of linear quadratic Gaussian control theory and Kalman filter theory. The performance index contains ride comfort, road holding and working space of suspension. The structural design variables taken are stiffness, daming properties and the position of the suspension system. The random road profile considered as colored noise is shaped from white noise by use of shaping filter. The performance of an optimal simultaneous structure/control system is compared with that of an optimal controlled system.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2014.02a
• /
• pp.370.1-370.1
• /
• 2014

Giant magnetoresistance (GMR), tunneling magnetoresistance (TMR), and magnetic random-access memory (MRAM) are currently active areas of research. Magnetite, Fe3O4, is predicted to possess as half-metallic nature, ~100% spin polarization (P), and has a high Curie temperature (TC~850 K). On the other hand, Spinel ferrite CoFe2O4 has been widely studies for various applications such as magnetorestrictive sensors, microwave devices, biomolecular drug delivery, and electronic devices, due to its large magnetocrystalline anisotropy, chemical stability, and unique nonlinear spin-wave properties. Here we have investigated the magneto-transport properties of epitaxial CoxFe3-xO4 thin films. The epitaxial CoxFe3-xO4 (x=0; 0.4; 0.6; 1) thin films were successfully grown on MgO (100) substrate by molecular beam epitaxy (MBE). The quality of the films during growth was monitored by reflection high electron energy diffraction (RHEED). From temperature dependent resistivity measurement, we observed that the Werwey transition (1st order metal-insulator transition) temperature increased with increasing x and the resistivity of film also increased with the increasing x up to $1.6{\Omega}-cm$ for x=1. The magnetoresistance (MR) was measured with magnetic field applied perpendicular to film. A negative transverse MR was disappeared with x=0.6 and 1. Anomalous Hall data will be discussed.

• Journal of the Korea Concrete Institute
• /
• v.21 no.5
• /
• pp.581-588
• /
• 2009

An amount of electric arc furnace slag, by-products generated in iron manufacture, is being increased. Therefore, it is required to recycle the electric arc furnace slag. Currently, it is possible to use the electric arc furnace slag as the aggregates of the concrete through the insurance of volume stability but not in the past because of the expansibility of f-CaO and f-MgO. In this study, simple beam tests via Ichinose method were performed to estimate the bond properties of reinforced concrete (RC) beams using the electric arc furnace slag. The results of the test showed that the showed that specimens using the electric arc furnace oxidizing slag aggregates have similar or more bond capacity relative to the specimen of natural aggregates. Especially, bond capacity of the specimens using the slag aggregates was almost one and a half times higher than a specimen using natural aggregates.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2012.02a
• /
• pp.332-332
• /
• 2012

분자선 에피탁시(molecular beam epitaxy)를 이용하여 GaAs 기판에 성장한 InAs 양자점(QDs: quantum dots)은 성장 온도, 압력, As/In의 공급비 등의 성장 조건에 따라 다른 변수(parameter)를 갖는다. 따라서 성장변수에 따라 양자점의 모양과 크기, 밀도가 달라져 균일한 양자점 형성에 어려움이 있어 많은 연구가 진행되고 있다. 예를 들면 In-interruption 법으로 성장한 양자점의 특성이 S-K mode (Stranski-Krastanov mode)로 성장한 양자점에 비해 광학적 특성이 향상되었다. 본 연구에서는 In pre-deposition (IPD) 법으로 성장한 InAs/GaAs 양자점의 광학적 특성을 PL(photoluminescence)와 TRPL (time-resolved PL)을 이용하여 분석하였다. InAs QDs 시료들은 In과 As 공급시간을 각각 1초와 19초 (QD1), 2초와 18초 (QD2), 3초와 17초 (QD3)로 조절하여 성장하였으며, In이 공급되는 시간 동안 As shutter를 차단하여 As 공급을 중단하였다. In과 As의 차단 없이 S-K mode로 성장한 시료를 기준시료로 사용하였다 (QD0). AFM (atomic force microscope) 측정결과, In 공급시간이 1초에서 2초로 증가할 때, 양자점의 밀도와 종횡비(aspect ratio)가 증가하였고, 양자점의 균일도가 증가하였다. 그러나 QD3 시료는 QD1 시료에 비해 밀도와 종횡비, 균일도가 감소하였다. 10 K에서 PL 피크는 In 공급 시간이 증가할 때, 970 nm에서 1020 nm로 적색편이 하였고 반치폭 (FWHM: full width at half maximum)은 75 meV에서 85 meV로 증가하였다. QD2 시료의 PL 피크 에너지가 가장 낮았고, 가장 강한 PL 세기를 보였다. IPD 시간이 증가함에 따라 PL 피크에서 측정한 PL 소멸은 점차 빨라졌다. IPD 기법으로 성장한 양자점의 빠른 PL 소멸은 양자점 밀도와 종횡비 향상에 의한 파동함수 중첩의 증가와 구속 에너지 증가에 의한 것으로 설명된다.

• Journal of the Korean Association of Oral and Maxillofacial Surgeons
• /
• v.46 no.5
• /
• pp.328-334
• /
• 2020

Objectives: This study aimed to validate the effectiveness of a recently proposed difficulty index for removal of impacted mandibular third molars based on extraction time and suggest a modified difficulty index including the presence of pathologic conditions associated with third molars. Materials and Methods: This retrospective study enrolled 65 male patients younger than 25 years with third molars. Extraction time was calculated from start of the incision to the last suture. The difficulty scores for third molars were based on spatial relationship (1-5 points), depth (1-4 points), and ramus relationship (1-3 points) using cone-beam computed tomography. The difficulty index was defined as follows: I (3-4 points), II (5-7 points), III (8-10 points), and IV (11-12 points). The modified difficulty score was calculated by adding one point to the difficulty score if the third molar was associated with a pathologic condition. Two modified difficulty indices, based on the presence of pathologic conditions, were as follows: the half-level up difficulty index (HDI) and the one-level up difficulty index (ODI) from the recently proposed difficulty index. Results: The correlations between extraction time and difficulty index and or modified difficulty indices were significant (P<0.001). The correlation coefficient between extraction time and difficulty index was 0.584. The correlation coefficients between extraction time and HDI and ODI were 0.728 and 0.764, respectively. Conclusion: Extraction time of impacted third molars exhibited a moderate correlation with difficulty index and was strongly correlated with the modified indices. Considering the clinical implications, the difficulty index of surgical extraction should take into consideration the pathologic conditions associated with third molars.