• 대한전기학회:학술대회논문집
• /
• 대한전기학회 2005년도 추계학술대회 논문집 전기기기 및 에너지변환시스템부문
• /
• pp.147-149
• /
• 2005

On this study, we optimized maximizing thrust force of weight ratio and minimizing detent force of weight ratio at the TFLM(Transverse Flux Linear Motor) using design of experiments by the table of orthogonal array, characteristic function and analysis of means(ANOM), For two functions or more, the effectiveness of design change can be evaluated in accordance with change in design parameters. Also, The stator and mover weight of TFLM is reduced by up to 20 percent while its thrust force of weight ratio and detent force of weight improved. From now on, we are going to apply the required technique to design various uses and shares of the TFLM.

• 대한기계학회논문집B
• /
• 제30권9호
• /
• pp.873-881
• /
• 2006

The present study investigates the pressure drop characteristics in rotating two-pass ducts. The duct has an aspect ratio (W/H) of 0.5 and a hydraulic diameter $(D_h)$ of 26.67mm. Rib turbulators are attached crossly in the four different arrangements on the leading and trailing surfaces of the test ducts. The ribs have a rectangular cross section of $2mm(e){\times}3mm(w)$ and an attack angle of $70^{\circ}C$. The pitch-to-rib height ratio (pie) is 7.5, and the rib height-to-hydraulic diameter ratio $(e/D_h)$ is 0.075. The results show that the highest pressure drop among each region appears in the turning region for the stationary case, but appears in the upstream region of the second pass for the rotating case. Effects of cross rib arrangements are almost the same in the first pass for the stationary and rotating cases. In the second pass, however, heat transfer and pressure drop are high for the cases with cross NN or PP type ribs in the stationary ducts. In the rotating ducts, they are high for the cases with cross NP or PP type ribs.

• 대한기계학회논문집B
• /
• 제30권9호
• /
• pp.882-890
• /
• 2006

The present study investigates the pressure drop characteristics in rotating two-pass ducts. The duct has an aspect ratio (W/H) of 0.5 and a hydraulic diameter $(D_h)$ of 26.67mm. Rib turbulators are attached parallel in the four different arrangements on the leading and trailing surfaces of the test ducts. The ribs have a rectangular cross section of $2m(e){\times}3mm(w)$ and an attack angle of $70^{\circ}C$. The pitch-to-rib height ratio (p/e) is 7.5, and the rib height-to-hydraulic diameter ratio $(e/D_h)$ is 0.075. The results show that the highest pressure drop among each region appears in the turning region for the stationary case, but appears in the upstream region of the second pass for the rotating case. Effects of parallel rib arrangements are almost the same in the first pass for the stationary and rotating cases. In the second pass, however, heat transfer and pressure drop are high for the cases with parallel NN or PP type ribs in the stationary ducts. In the rotating ducts, they are high for the cases with parallel NN or PN type ribs.

• 한국감성과학회:학술대회논문집
• /
• 한국감성과학회 2001년도 추계학술대회 논문집
• /
• pp.169-172
• /
• 2001

There are many people who suffer from simulation sickness when immersing in virtual reality. In this study, we analyzed two photoplethysmogram(PPG) parameters - a second derivative parameter and power spectral density ratios - in order to relate PPG parameters with simulation sickness. 36 young, healthy subjects were participated in the experiment, and each subject was equipped with a PPG electrode during his or her immersion. Simulation sickness section was defined as a 7 - second section which starts from the point where a subject reported simulation sickness, and normal section as a same-length section where no physical stimuli was presented to him or her. We compared the PPG parameters of the simulation sickness sections with the normal sections, - d/a ratio is believed to have lower value during vasodilation and higher value during vasoconstriction, however, we could not find much difference in the parameter between normal and simulation sickness sections. We also compared 1 to 10Hz power spectral density ratios in normal sections with in simulation sickness section, and found that 6 density ratios among them have different value. Therefore, the density ratios might be utilized as parameters to detect simulation sickness of subjects.

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 2010년도 춘계학술대회 논문집
• /
• pp.623-624
• /
• 2010

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 2010년도 추계학술대회 논문집
• /
• pp.543-544
• /
• 2010

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 2011년도 춘계학술대회 논문집
• /
• pp.645-646
• /
• 2011

• 한국수소및신에너지학회논문집
• /
• 제22권1호
• /
• pp.100-108
• /
• 2011

The use of biogas as an energy source reduces the chance of possible emission of two greenhouse gases, $CH_4$ and $CO_2$, into the atmosphere at the same time. Its nature of being a reproducible energy source makes its use even more attractive. This research if for the hydrogen production through the steam reforming of the biogas. The biogas utilized 3D-IR matrix burner in which the surface combustion is applied. The nickel catalyst was used inside a reformer. Parametric screening studies were achieved as Steam/Carbon ratio, biogas component ratio, Space velocity and Reformer temperature. When the condition of Steam/Carbon ratio, $CH_4/CO_2$ ratio, Space velocity and Refomer temperature were 3.25, 60%:40%, 19.32L/$g{\cdot}hr$ and $700^{\circ}C$ respectively, the hydrogen concentration and methane conversion rate were showed maximum values. Under the condition mentioned above, $H_2$ concentration was 73.9% and methane conversion rate was 98.9%.

• 한국재난정보학회 논문집
• /
• 제13권3호
• /
• pp.366-375
• /
• 2017

콘크리트의 압축강도에 영향을 미치는 요인에는 공시체의 치수, 형상, 길이비(h/d), 단면 처리방법 및 공시체의 건습 등을 들 수 있다. 콘크리트 구조물의 코어 채취 시, 배근 간격에 의한 철근 절단, 벽두께, 구조물에 미치는 악영향 등을 고려할 때, 공시체 치수나 길이비를 2/1로 맞추기가 어려우므로 품질 관리 시 공시체 치수 및 길이비에 대한 강도의 보정이 필요하다. KS의 경우, 콘크리트에서 절취한 코어 나 보의 강도 시험 방법에서 길이비에 대한 보정 계수를 정하고 있으나, 최근 콘크리트의 고강도화가 진행됨에 따라 이를 일괄적으로 적용하기에는 다소 무리가 있다는 연구가 보고되고 있다. 본 연구에서는 압축강도 40~60MPa 범위의 콘크리트를 대상으로 공시체 크기와 길이비의 영향(이하 길이효과)과 길이비를 2/1로 유지하면서 치수의 변화에 따른 강도추이를 검토하기 위해 공시체 직경을 ${\emptyset}5{\sim}15cm$, 길이비를 2.0~1.25로 변화시킨 경우의 압축강도 시험 값을 KS F 2422에 의한 보정 계수와 비교하고, 고강도 콘크리트에의 적용 가능성을 확인하는데 그 목적이 있다.

• Steel and Composite Structures
• /
• 제26권6호
• /
• pp.693-703
• /
• 2018

To better understand the influence of hollow ratio on the hollow concrete-filled circular steel tubular (H-CFT) stub columns under axial compression and to propose the design formula of ultimate bearing capacity for H-CFT stub columns, 3D finite element analysis and laboratory experiments were completed to obtain the load-deformation curves and the failure modes of H-CFT stub columns. The changes of the confinement effect between core concrete and steel tube with different hollow ratios were discussed based on the finite element results. The result shows that the axial stress of concrete and hoop stress of steel tube in H-CFT stub columns are decreased with the increase of hollow ratio. AfteGr the yield of steel, the reduction rate of longitudinal stress and the increase rate of circumferential stress for the steel tube slowed down. The confinement effect from steel tube on concrete also weakened slowly with the increase of hollow ratio. Based on the limit equilibrium method, a simplified formula of ultimate bearing capacity for the axially loaded H-CFT stub columns was proposed. The predicted results showed satisfactory agreement with the experimental and numerical results.