• 대한치과보철학회지
• /
• 제36권2호
• /
• pp.293-301
• /
• 1998

The purpose of this study was to investigate the effects of load on root that was applied to edentulous area in three simulated situation, in each case the guiding planes of abutment were right vertical, 95 degrees, or 100 degrees to residual ridge. The 2-dimensional finite element method was used and the finite element model was prepared as fellows. Right mandibular 1st and 2nd molar was lost and the 2nd premolar with distal rest was used as primary abutment which had three different degrees of guiding plane. Then 150N of compressive force was applied to central fossae of the 1st and 2nd molars and von Mises stress and displacement was measured. The results were as follows; 1. Irrespective of slopes of guiding planes, the stress was concentrated on mesial side of root apex and distal side of coronal portion of root, in particular on junction with distal alveolar bone. As slopes of guiding planes were increased. stress on root and compact bone surrounding abutment was increased but no considerable effect was seen on compact bone of residual ridge. 2. Distal side of coronal portion of root limited by periodontal ligament was displaced distally and mesial side of apical portion was mesially. With slope of guiding plane increasing, the pattern of displacement was similar with one another but the quantity was increased. 3. Both abutment & alveolar bone were displaced downward and root of abutment, especially distal side of coronal portion, was displaced severely. As the guiding plane was tiffed more mesially over $90^{\circ}$, the degree of displacement was also increased.

• 천문학논총
• /
• 제27권5호
• /
• pp.391-397
• /
• 2012

The SPICA (SPace Infrared Telescope for Cosmology & Astrophysics) project is a next-generation infrared space telescope optimized for mid- and far-infrared observation with a cryogenically cooled 3m-class telescope. It will achieve the high resolution as well as the unprecedented sensitivity from mid to far-infrared range. The FPC (Focal Plane Camera) proposed by KASI as an international collaboration is a near-infrared instrument. The FPC-S and FPC-G are responsible for the scientific observation in the near-infrared and the fine guiding, respectively. The FPC-G will significantly reduce pointing error down to below 0.075 arcsec through the observation of guiding stars in the focal plane. We analyzed the pointing requirement from the focal plane instruments as well as the error factors affecting the pointing stability. We also obtained the expected performance in operation modes. We concluded that the FPC-G can achieve the pointing stability below 0.075 arcsec which is the requirement from the focal plane instruments.

• 대한치과기공학회지
• /
• 제34권4호
• /
• pp.473-482
• /
• 2012

Purpose: The purpose of this study was to investigate the stress distribution of the surrounding tissues according to 3 proximal plate types of the RPI clasp. Methods: The removeable partial denture which mandibular right and left second premolars and mandibular molars were lost was attached to a three dimensional photo elastic epoxy resin model. Then 120N of vertical load was applied. After 3-dimensional photoelastic stress analysis was used to record the isochromatic fringe patterns. Results: Kratochvil type guiding plane exhibited little uniform stress distribution on load center and alveolar ridge, but higher stress concentration on buccal surface of second premolar. Krol type guiding plane exhibited the stress concentration on the front of load center and relatively higher stress concentration on buccal surface of first premolar. However, this type had no effect on canine. Researcher type guiding plane showed the stress concentration on second premolar and molar, but the little stress distribution on first premolar. Conclusion: In all types, excessive stress concentration was appeared and three types were not significant different.

• 한국도서관정보학회지
• /
• 제21권
• /
• pp.195-229
• /
• 1994

This article investigates the normative principles suggested by Rangannathan as the guiding principles for his theories, consisting of basic laws, fundamental laws, canons, principles and postulates. His five basic laws and five laws of library science are re-interpreted from the view point of library classification. And three planes of idea plane, verbal plane and notational plane, one of the core ideas in his analytico-synthetic theory of library classification, are analyzed. This article also suggests the demonstration model for this three planes using the ideas from chemistry ad chemical equation. In the last part, it analyzes the canons for library classification of three planes. These normative principles are basically guiding principles for so-called analytico-synthetic or faceted classification. But they can be a n.0, pplied to most of modern classification. But they can be a n.0, pplied to most of modern classification schemes, especially to semi-enumerative schemes including DDC, KDC, etc. so that they can improve the schemes. From this regard, these principles can also be helpful to the KDC, on the verge of the revision of its fourth edition.

• 천문학회보
• /
• 제37권1호
• /
• pp.64.2-64.2
• /
• 2012

The SPICA (SPace Infrared Telescope for Cosmology & Astrophysics) project is a next-generation infrared space telescope optimized for mid- and far-infrared observation with a cryogenically cooled 3m-class telescope. It will achieve the high resolution as well as the unprecedented sensitivity from mid to far-infrared range. The FPC (Focal Plane Camera) is a Korean-led near-infrared instrument as an international collaboration. The FPC-S and FPC-G are responsible for the scientific observation in the near-infrared and the fine guiding, respectively. The FPC-G will significantly reduce the alignement and random pointing error through the observation of guiding stars in the focal plane. We analyzed the pointing requirement from the focal plane instruments. The feasibility study was performed to achieve the requirements. Here, we present the role of SPICA/FPC as a fine guiding camera.

• 대한치과보철학회지
• /
• 제18권1호
• /
• pp.7-13
• /
• 1980

The purpose of this study was to evaluate the removable partial denture prescriptions including surveyed crowns and design of component parts sent to the laboratory technician. A total of 351 casess with prescription forms and master cast in maxillary and mandibular semi-edentulous situations collected from dental laboratory by random sampling were selected for this study. The evaluation and study observed here involved the classification of edentulous situations, status of abutment splinting, form of rest seats and guiding plane of surveyed crows, location of maxillary major connectors and tripodig marks on the master casts. Removable partial denture prescriptions contained (1) general request (upper and lower cast framework), (2) types of metal, (3) location of retainer(retention, lingual bracing, rest area, guiding plane surface), (4) location and type of major connector, (5) relief area and amount, (6) and other specific instructions. The following informations based on the classified groups such as Group I was those cases sent with no real prescriptions. They say 'make a partial.' No prescriptions, no thought beforehand, Group II was those cases sent with a minimal prescriptions. They say 'make a partial with clasps on May be some preparations, usually inadequate. Group III was those cases sent with a moderately good prescription. Adequate but could be much better. No tripoding but it tell what clasps go where. Still not good prescriptions. Group IV was good cases, tripoded with adequate prescriptions and a prescription which exactly describes what is expected from the laboratory. The analyzed results were as follows: 1. The normal form of rest seats and guiding plane of surveyed crowns in Class. I and Class. II edentulous situations on the maxillary cast were observed 31.9% and 27.89%, respectively. The abutment teeth and retainer without occlusal rests of Class. I and Class. II were showed 11.58% and 8.86%, respectively. In mandibular cases, the normal form of rest seats and guiding plane of surveyed crowns showed 27.54% and 8.82% in Class. I and Class. II situation. The abutment teeth and retainer without rest seats were showed 15.19%, respectively. 2. The splinted surveyed crowns of Class. I and Class. II maxillary edentulous situations in distal extension cases were showed 34.51% and 28.85%, but 28.52% and 10.29%, respectively. 3. The location and type of maxillary major connector delineated on the master cast were 66 cases (44.89%). 4. The results of 351 cases were classified as Group I 146(41.59%), Group II 115 (32.76%), Group III 57 (16.23%), and Group IV 33 (9.48%). 5. The delineation of abutment tooth for clasping were 176 cases (50.14%) among total of 351 cases. 6. The delineation of height of contour line were showed 45 cases (12.8%) in Group II, 14 cases (3.98%) in Group III and 33 cases (9.40%) in Group IV with total 92 cases (26.21%). 7. In surveying procedure, the delineation of tripoding marks and reference line were showed 17 cases (4.84%).

• 천문학회보
• /
• 제38권2호
• /
• pp.83.2-83.2
• /
• 2013

Camera for QUasars in EArly uNiverse (CQUEAN) is an optical CCD camera developed by the Center for the Exploration of the Origin of the Universe (CEOU). In 2010 August, CQUEAN was attached on the 2.1m Otto Struve Telescope at the McDonald Observatory in Texas, USA. As the main purpose of CQUEAN is detecting the Lyman breaks of redshift ~5 quasars, it is sensitive to near-infrared wavelengths (0.7-1.0 ${\mu}m$). For the auto-guiding system, it is using a rotating guide arm to find guide stars on the Cassegrain off-axis focus of the telescope. We plan to upgrade a new filter wheel system consists of a series of narrow band filters. We will install this independent auto-guiding units on the finder scope, which makes rooms on the Cassegrain focal plane of the main telescope. In this presentation we present the system architecture of the CQUEAN Auto-guiding Package (CAP).

• 대한치과보철학회지
• /
• 제37권5호
• /
• pp.581-596
• /
• 1999

하악 우측 제1대구치 및 제2대구치가 손실된 2급하악 후방연장 국소의치에서 무치악 부위 지대치 유도면의 기울기와 형태가 지지조직에 미치는 응력 및 변위를 비교 분석하기 위하여 3차원 유한요소법을 이용하여 알아보았다. Kratochvil 형태의 유도면의 기울기가 잔존치조제에 대하여 $90^{\circ}$인 경우, $95^{\circ}$인 경우, 그리고 $100^{\circ}$인 경우와 Krol형태의 유도면의 기울기가 $90^{\circ}$인 경우에 있어서 제2소구치를 지대치로 하고 RPI형태의 유지장치를 사용하는 경우를 가정하여 모델링한 다음 제1대구치 및 제2대구치의 중심와에 150N의 하중을 가하여 응력 및 변위에 대하여 실험한 결과 다음과 같은 결론을 얻었다. 1. Kratochvil의 유도면 형태 중 기울기가 $90^{\circ}$인 경우와 Krol의 유도면 형태에서는 유사한 응력 분포를 나타내었으며 특히 지대치에서 치근단 방향으로 응력이 향하는 것으로 나타났다. 2. 유도면의 기울기가 $95^{\circ}$인 경우에서는 지대치의 치근단 부위에 응력이 증가하면서 근심방향으로 향하였으며, $100^{\circ}$인 경우에서는 치근단의 응력이 협측 및 근협측 방향으로 집중되어 나타났다. 3. 유도면의 기울기가 $90^{\circ}$인 경우에서는 지대치의치근이 조금 시계방향으로 비틀리는 양상으로 나타났으며, Krol의 유도면 형태에서는 지대치가 치근단 부위에서는 원설측으로 치경부에서는 근협측으로 변위되었다. 4. 유도면의 기울기가 $95^{\circ}$인 경우에서는 지대치의 치근은 치근단 부위에서 근설측으로 약간 변위되었고 치경부 방향으로 갈수록 반시계 방향으로 비틀리면서 보다 많이 변위되었으며, $100^{\circ}$인 경우에서는 지대치 치근단에서는 근협측으로 변위되었고 치경부방향으로 갈수록 시계방향으로 비틀리면서 보다 많이 변위되었다.

• 한국통신학회논문지
• /
• 제25권5A호
• /
• pp.688-695
• /
• 2000

본 논문에서는 체적 홀로그래픽 메모리 저장 기술을 이용한 다시점 스테레오스코픽 디스플레이 시스템을 제안하였다. 디스플레이 평면에서 다시점 3D 영상을 관찰할 수 있도록 공간 다중화된 평면 기준파와 각 다중화된 명면 물체파를 간섭시킨 후 광굴절 매질에 기록하였다. 재생시 다안식 영상으로 구성된 물체파가 시분할적으로 update 되며 브래그 조건을 만족시켜면, 출력 평면에서 다안식 스테레오 영상을 관찰할 수 있다. 체적 홀로그램을 이용한 다시점 디스플레이시스템의 실험과 이론적인 분석을 하였다.

• 천문학회보
• /
• 제36권2호
• /
• pp.126.1-126.1
• /
• 2011

The SPICA (SPace Infrared Telescope for Cosmology & Astrophysics) project is a next-generation infrared space telescope optimized for mid- and far-infrared observation with a cryogenically cooled 3m-class telescope. Owing to unique capability of focal plane instruments onboard SPICA, it will enable us to resolve many astronomical key issues from the star-formation history of the universe to the planetary formation. The FPC (Focal Plane Camera) is a Korean-led near-infrared instrument as an international collaboration. Korean consortium for FPC proposed a key instrument responsible for a fine guiding (FPC-G). The back-up of FPC-G will make scientific observations as well. We have examined the legacy science programs for FPC and performed the feasibility study for the fine guiding system. Recently, the international review process is now in progress, in order to make a selection of the focal plane instruments. Here, we report the current status of SPICA/FPC project.