• The KSFM Journal of Fluid Machinery
• /
• v.13 no.5
• /
• pp.11-16
• /
• 2010

The development of lifting pumps that lift minerals to a mining vessel are one of the vital parts of the commercial mining process. The purpose of this study is to investigate internal flow and its effect on the performance of a mixed flow pump in order to improve the pump's performance. Numerical analysis was performed by commercial code of ANSYS CFX-11 based on flow rate and length of flexible hose. The rated rotational speed of the impeller is 1750rpm. For taking into account the turbulence, k-$\omega$ SST model was selected to guarantee more accurate prediction of flow separation. The simulated results are in good agreement with the experimental results and showed that its efficiency and the head of the pump are related mainly to the flow rate and the length of flexible hose. A lesser flow rate caused more secondary flow through the guide vane passage. The length of flexible hose and flow rate exert much more influence on the pump's performance than the shape of the flexible hose.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.12 no.2
• /
• pp.133-138
• /
• 1987

In this paper the tuning characteristics of resonant frequencies are experimentally studied through the variation of the length of the inner conducting rod in a re-enterant eavity resonator. The re-enterant eavity resonator consists of a coaxial cable and a cylindrical wave guide. The length of the inner conducting rod can be varied to the longitudinal direction. The resonant frequencies of TMonq modes are measured according to the arbitrary length. In order to verify the propriety of experimental results, experimental results are compared with other theoretical results. The results in this paper can be applied to wave meter and resonant circuit of amplifier. They will be use to vary resonant frequencies of a dielectric resonator in MIC and filter.

• Journal of the Korean Society for Precision Engineering
• /
• v.24 no.3 s.192
• /
• pp.117-123
• /
• 2007

This paper describes a three-probe system that can be used to measure the parallelism and straightness of a pair of rails simultaneously. The parallelism is measured using a modified reversal method, while the straightness is measured using a sequential two-point method. The measurement algorithms were analyzed numerically using a pair of functionally defined rails to validate the three-probe system. Tests were also performed on a pair of straightedge rails with a length of 250 mm and a maximum straightness deviation of $0.05{\mu}m$, as certified by the supplier. The experimental results demonstrated that the parallelism-measurement algorithm had a cancellation effect on the probe stage motion error. They also confirmed that the proposed system could measure the slope of a pair of rails about $0.06{\mu}rad$. Therefore, by combining this technique with a sequential differential method to measure the straightness of the rails simultaneously, the surface profiles could be determined accurately and eliminate the stage error. The measured straightness deviation of each straight edge was less than $0.05{\mu}m$, consistent with the certified value.

• Korean Journal of Optics and Photonics
• /
• v.11 no.6
• /
• pp.423-428
• /
• 2000

We have demonstrated a -8 dB additional reduction in the intensity sidelobe of an apodized-interaction-strength guide-wave acousto-optic filter with a center passband of 1551.6 nm. Acoustic-intensity weighting was achieved by launching a surface acoustic wave (SAW) beam in a straight acoustic waveguide, and gradually transferring this SAW intensity to the active device, and back out, by evanescent-wave coupling across a 50 !lm barrier over a 19 rom interaction length. The intensity sidelobe was -4.27 dB for an unapodized filter with abmpt onset and cutoff of the interaction, but sidelobes were reduced to at most -12.68 dB for a SAW intensity with raised-cosine weighting. The RF driving power was 17.78 mW. A linear tuning rate of 8.86 nmIMHz and a spectral width of -1.7 nm were demonstrated. rated.

• Wind and Structures
• /
• v.26 no.3
• /
• pp.115-128
• /
• 2018

Appropriate modeling of a tornado-like vortex is a prerequisite when studying the near-ground wind characteristics of a tornado and tornado-induced wind loads on structures. Both Ward- and ISU-type tornado simulators employ guide vanes to induce angular momentum to converge flow in order to generate tornado-like vortices. But in the Ward-type simulator, the guide vanes are mounted near the ground while in the ISU-type they are located at a high position to allow vertical circulation of flow that creates a rotating downdraft to generate a tornado-like vortex. In this study, numerical simulations were performed to reproduce tornado-like vortices using both Ward-type and ISU-type tornado simulators, from which the effects of rotating downdraft on the vortex characteristics were clarified. Particular attention was devoted to the wander of tornado-like vortices, and their dependences on swirl ratio and fetch length were investigated. The present study showed that the dynamic vortex structure depends significantly on the vortex-generating mechanism, although the time-averaged structure remains similar. This feature should be taken into consideration when tornado-like-vortex simulators are utilized to investigate tornado-induced wind forces on structures.

• Journal of the Korean Society for Precision Engineering
• /
• v.19 no.5
• /
• pp.139-148
• /
• 2002

Motion errors of linear motion guideway are analyzed theoretically in this paper. For the analysis, an new algorithm predicting motion errors of bearing and guideway is proposed using the Hertz's elastic deformation theory. Accuracy averaging effect can be calculated quantitatively by analyzing relationship between motion errors of guideway and spatial frequency of rail form error. Influences of design parameters on the motion errors including the number of balls, preload, ball diameter, bearing length and the number of bearings are analyzed. As it is difficult to measure the rail form error, experimental results are compared with results analyzed by the equivalent analysis method which evaluate the motion errors of guideway using the measured errors of bearing. From the experimental results, it is confirmed that the proposed analysis method it effective lo analyze the motion errors of linear motion bearing and guideway.

• Journal of Biosystems Engineering
• /
• v.33 no.1
• /
• pp.14-20
• /
• 2008

An agricultural unmanned helicopter was suggested for an alternative to current pesticide application methods to solve such problems as high cost, low efficiency, shirking task and unsafe work. To pursuit this trend, researches on the development of unmanned helicopters have been accelerated in Korea as well. In this research, a guide type centrifugal clutch that plays an important role in the unmanned helicopter was studied. Theoretical analyses and experimental tests were conducted for designing an optimal clutches. Main design factors of the guide type centrifugal clutch were found to be spring constant, free length of spring, mass of friction sector, contact area, allowable pressure, number of friction sector, friction coefficient, radius of drum, and clutch arrangement. And these design factors could be the functions of engaging engine speed and desired power transfer capacity. The result of the single clutch test showed the power transfer capacity of 14.1 PS at 5,800 rpm and the result of the dual clutch test showed that the capacity of 17.7 PS at 5,600 rpm. These experimental results agreed well the theoretical simulations.

• Fisheries and Aquatic Sciences
• /
• v.16 no.1
• /
• pp.15-23
• /
• 2013

Normal embryonic development at a constant temperature ($18^{\circ}C$) has been described for the Siberian sturgeon Acipenser baerii (Acipenseriformes). Hormone-induced spawning and artificial insemination were performed to prepare embryonic batches for embryologic examination. After insemination, early cleavages of the Siberian sturgeon embryos continued for 7 h post-fertilization (HPF), showing the typical pattern of uneven holoblastic cleavage. Blastulation and gastrulation began at 9 HPF and 19 HPF, respectively. Epiboly formation (2/3 covered) was observed at 25 HPF during gastrulation. Neurulation was initiated with the formation of a slit-like neural groove from the blastopore at 33 HPF. During neurulation, the primary embryonic kidney (pronephros) and s-shaped heart developed. The embryos underwent progressive differentiation, which is typical of Acipenseriform species. A mass hatching was observed at 130 HPF, and the average total length of the hatched prolarvae was 10.5 mm. The hatched prolarvae possessed a typical pigment plug (yolk plug). The results of this study are valuable not only as a reference guide for the artificial propagation of Siberian sturgeon in hatcheries but also as the basis for the derivation of developmental gene expression assays for this species.

• Korean Journal of Optics and Photonics
• /
• v.23 no.3
• /
• pp.119-123
• /
• 2012

The structure of an LCD backlight unit (BLU) was simplified by installing a micro reverse-pyramid array (MRPA) or a micro reverse-cone array (MRCA) on the top surface of the light guide panel (LGP) in order to eliminate the conventional diffuser sheet and the prism sheet. The optimum conditions of the MRPA and the MRCA in the new light guide panel were obtained through optical simulation. The change of the luminance and view angle that depend on the side angle, the height, and the length at the top of the MRPA and MRCA were studied. The optimized side angle and the view angle of the MRPA and MRCA were 59 and 57 degrees for the side angles and 68 and 64 degrees for the view angles, respectively.

• Journal of Biomedical Engineering Research
• /
• v.23 no.4
• /
• pp.263-268
• /
• 2002

The image quality of imageguide depends on the structure, material, length of microfibers and the phenomena such as cross-talk and leaky ray between adjacent fibers. These Parameters should be considered as important factors in the image transmission qualify of fibers. However it is considered to be very difficult to assess all the parameters in a consistent way Therefore. two image characteristics, image resolution and image brightness are measured and analyzed to determine the image quality of imageguide. But the exact methods to measure two image characteristics of imageguide are not reported. In this study, the image brightness of imageguide for ultrathin endoscope is determined by measuring of the numerical aperture. the packing fraction and the attenuated power ratio of imageguide. Especially it is possible to obtain more exact results from measuring the numerical aperture of whole image guide than those from theoretical calculation of the single microfiber in an image guide. The image brightness of the image guide which has $3.1\mu m$ microfibers is about 37% less than that with $4.1\mu m$ microfibers.