• 소음진동
• /
• 제5권2호
• /
• pp.235-246
• /
• 1995

Experiment on the modal balancing of a flexible rotor supported on two kinds of fluid film bearings is performed to verify the modal balancing theory. The fluid film bearings are a tilting pad bearing and a two axial grooved journal bearing. One is inherently stable, but the other is not. The experimental result shows that the modal balancing method is effective for balancing of a high speed flexible rotor system. Besides, the critical speeds and mode shapes measured experimentally are in good coincidence with the results of rotordynamic analysis. Oil whip, which is the instability phenomenon due to fluid film force, is also observed during the experiment.

• 한국정밀공학회지
• /
• 제17권9호
• /
• pp.145-150
• /
• 2000

Out-of-sphericity is degree of deformation of an air bearing sphere deviated from a perfect sphere. This paper investigates numerically the effect of out-of-sphericity error on the radial stiffness of an air bearing Three types of out-of-sphericity modes are considered. in this study the stiffness is calculated from pressure distribution at the bearing surface which is obtained by solving th Reynolds equation. in some cases large out-of-sphericity errors are found to improve the stiffnesses of air bearings. This implies that an air bearing of perfect hemispheres is not necessarily of the best performance. Thus much labor and cost in manufacturing air bearings can be saved, In addition the radial stiffness of an air bearing depends greatly on the application direction.

• 비파괴검사학회지
• /
• 제32권1호
• /
• pp.7-11
• /
• 2012

기존 진단법과 달리 동적 하중조건하 회전체의 마모 단계에 따른 결함 진단을 위해 비접촉, 비파괴의 적외선 열화상 기법이 제안된다. 본 연구에서는 시험시편인 단열 깊은 홈의 볼 베어링을 설정하여 기존의 스펙트럼 분석과 같은 고장탐지법에 대한 대안으로써 수동형 열화상시험이 수행되었다. 본 연구로부터, 적외선 열화상시험은 신뢰성을 평가하기 위해 기존 진동 스펙트럼 분석시험과 비교, 분석되었다. 연구의 비파괴시험의 결과로써, 마모 단계에 따른 볼 베어링의 온도 특성이 분석되었다.

• 한국정밀공학회지
• /
• 제16권2호통권95호
• /
• pp.23-30
• /
• 1999

This paper investigates the radial performance of self-acting spiral-grooved air bearing, used to support small high-speed rotating bodies. Repeatable runout, nonrepeatable runout, stiffness and supporting load are selected as the performance. The clearance between rotor and stator, the stator groove depth, and the rotating speed are chosen as three main parameters affecting the performances. Force application and displacement measurement are done in a noncontact manner, in order not to disturb operation: electromagnetic force is applied to the rotor and gap sensors are used to measure the displacement of the rotor. Experimental results show that repeatable runout decreases as speed, groove depth and clearance decrease. Nonrepeatable runout decreases as clearance decreases, and it has a minimum value at $5.5{\mu}m$ of grove depth and a maximum value at speed of 18.000rpm. Stiffness increases as speed increases and clearance decreases, and has a maximum value around $5.5{\mu}m$ of groove depth. The relationship between force and displacement is linear for small displacement, but becomes nonlinear for large displacement. Supporting load is linearly proportional to the stiffness, and it is a maximum value around $4.75{\mu}m$ of clearance.

• 한국소음진동공학회:학술대회논문집
• /
• 한국소음진동공학회 2004년도 춘계학술대회논문집
• /
• pp.748-752
• /
• 2004

Fluid dynamic bearings (FDBs) have been replacing ball bearings of the HDD spindle motor very rapidly. But there are several demerits of HDB, such as high friction torque, variable viscosity of the fluid lubricant depending on operating temperature, low stiffness, and etc. Eccentricity is one of the major parameters which affects the static and dynamic characteristics. As the static eccentricity is larger, the stiffness and the damping coefficients become bigger. But friction torque is relatively unaffected by the static eccentricity. This research proposes a new type of journal bearing with asymmetric journal grooves which results in better dynamic characteristics. The static and dynamic characteristics of the new journal bearing are investigated by solving the Reynolds' equation with FEM, and the transient analysis is performed to predict the dynamic behavior of rotor by solving the equations of motion of a HDD spindle system with Runge-Kutta method. The result shows that the proposed Journal bearings have much bigger stiffness and damping coefficients compared with the conventional symmetric ones. And consequently, it has smaller whirl radius and tilting angle.

• 한국소음진동공학회논문집
• /
• 제13권7호
• /
• pp.508-516
• /
• 2003

The dynamic characteristics of an ell-lubricated, short squeeze film damper (SFD) with a central feeding groove are derived based on a theoretical analysis considering the effect of a groove, and identified experimentally using an Active Magnetic Bearing (AMB) system as an exciter. In order to get the theoretical solution, the fluid film forces of the grooved SFD are analytically derived so that the dynamic coefficients of the SFD can be expressed in terms of its design parameters. For the experimental validation of the analysis, a test rig using an AMB as an exciter is proposed. As an exciter. the AMB represents a mechatronic device to levitate and position the test Journal without any mechanical contact, to generate relative motions of the Journal inside the tested SFD and to measure the generated displacements during experiments with fairly high accuracy. Using this test rig, experiments are extensively conducted with various values of clearance, which Is one of the most important design parameters. in order to investigate its effect on the dynamic characteristics and the performance of the SFD. Damping and Inertia coefficients of the SFD that are experimentally Identified are compared with the analytical results to demonstrate the effectiveness of the applied analysis. It Is also shown that the AMB is an ideal device for tests of SFDs.

• 비파괴검사학회지
• /
• 제31권2호
• /
• pp.134-138
• /
• 2011

회전기기의 고장 탐지에 있어 기존의 진단법과 달리 동적 하중조건 하에서 비접촉, 비파괴의 적외선 열화상 기법이 제안된다. 본 논문에서는 단열 깊은 홈 볼 베어링을 시편으로 하여, 회전기기의 기존의 고장 진단법 대신 수동형 열화상 기법을 이용한 시험을 수행하였다. 추가적으로, 제안된 방법의 효율성을 평가하기 위해 기존의 진동 스펙트럼 분석법을 적용하여 열화상 시험법을 비교하였다. 시혐의 결과로써, 동적 하중조건 하 볼 베어령의 온도분포 특성이 철저히 분석되었다.

• Tribology and Lubricants
• /
• 제15권1호
• /
• pp.77-82
• /
• 1999

The processing conditions fur the synthesis of platelet W $S_2$ lubricant powder through a solid-gas reaction were optimized. The mixture of tungsten and sulfur powders were sealed in a vacuum of 10$^{-6}$ torr, prior to heat-treating at 85$0^{\circ}C$ fur 8 days. The reaction product showed a well-developed platelet W $S_2$ powder with an average size of 3.8 ${\mu}{\textrm}{m}$. The TGA/DTA analysis of the synthesized W $S_2$ powder was performed up to 120$0^{\circ}C$ at a rate of 1$0^{\circ}C$/min in flowing air (100 ${\mu}{\textrm}{m}$/min) atmosphere. The weight loss was about 6% up to 120$0^{\circ}C$ compared to the original weight. A rapid weight loss of about 5% occurred in the temperature range of 44$0^{\circ}C$ to 66$0^{\circ}C$ and an exothermic peak observed due to the transition of W $S_2$ to W $O_3$. The synthesized W $S_2$powder was coated on the commercial deep grooved ball bearing (No. 6203) to examine the effect of W $S_2$, coating layer on the noise and endurance of the ball bearing. The level of noise obtained from W $S_2$, coated-ball bearing (56 ㏈) was higher. than the value (32 ㏈) occurred in the case of greece lubrication. The endurance of the ball-bearing assembled after the coating of W $S_2$ powder onto each part increased 50 times compared to the non-coated ball-bearing..

• Animal cells and systems
• /
• 제13권1호
• /
• pp.59-69
• /
• 2009

This paper documents the defining morphological characteristics of the larval stages of Chionoecetes tanneri Rathbun, 1893, the grooved Tanner crab, from specimens reared in the laboratory. Chionoecetes tanneri larval stages include two zoeae and one megalopa. The first zoea is characterized by: six setae on the posterior margin of the carapace; postero-lateral spines on abdominal somites 3 and 4, extending beyond the posterior margin of adjacent somites and bearing 9-10 spinnules; 12 plumose setae and one stout distal plumose seta present on the margin of the scaphognathite of the maxilla; and one fused lateral spine and one articulated dorso-medial spine on each fork of the telson. The second zoea is characterized by: 9 setae on the postero-lateral margin of the carapace; a serrated mandible molar; a mandibular palp bud; 25-26 plumose setae on the margin of the scaphognathite of the maxilla; pereiopods with well-developed gills and buds; and four pairs of stout setae on the posterior margin of the telson. For the megalopal stage, the distinguishing characteristics include: a rostral spine equal in length to the supraorbital spine; six setae on the exopod of the uropod; and a single spine on the ischium of the second pereiopod. This study allows C. tanneri larvae to be distinguished from the larvae of known sympatric congeners. This information provides a basic taxonomic tool for researchers in fisheries management and zooplankton ecology who are addressing issues related to trophic interactions, metapopulation dynamics and ecosystem impacts in the evolving marine resource management strategies in the North Pacific, and those related to Chionoecetes species in particular.

• 소음진동
• /
• 제7권6호
• /
• pp.1015-1023
• /
• 1997

Rotordynamic analysis of a multistage turbine pump using finite element method is performed to investigate the effects of seal wear on its system behavior. Stiffness and damping coefficents of the 2-axial grooved bearing are obtained as functions of rotating speed. Stiffness and damping coefficients of plane annuler seals are calculated as functions of rotating speed as well as seal clearance of seals become larger, these stiffness and damping coefficients decrease drastically so that there can be significant changes in whirl natural frequencies and damping characteristics of the pump rotor system. Although a pump is designed to operate with a sufficient seperation margin from the 1st critical speed, seal wear due to long operation may cause a sudden increase in vibration amplitude by resonance shift and reduce seal damping capability.