• 한국환경과학회지
• /
• 제27권6호
• /
• pp.411-423
• /
• 2018

To investigate the distribution characteristics of grain size and organic matter of surface sediments from the Nakdong-Goryeong Mid-watershed, surface sediments were collected and analyzed. The samples were collected from six sited at four different times between May 2013 and May 2014. The were analyzed for grain size, water content, ignition loss, chemical oxygen demand, total organic carbon and total nitrogen. The surface sediments were mainly composed of medium sand (mean 44.7%) and coarse sand (mean 32.8%) and became coarser in May 2014. Fine sediments at the site NG-2 were poorly sorted and positively skewed, and occur in a tributary environment that is relatively low-energy compared with the other sites. The water content at the studied sites (15.3 ~ 34.9%) averaged 20.25%, and ignition loss (0.4 ~ 5.8%) and total nitrogen (274 ~ 2493 mg/kg) averaged 1.33% and, 696 mg/kg, respectively. These values indicated that the sediments were not seriously contaminated when compared with the sediment pollution evaluation standard of the National Institute of Environmental Research. The chemical oxygen demand (mean 0.17%) was at the non-polluted level compared with United States Environmental Protection Agency sediment quality standards. The total organic carbon (mean 0.18%) at all sites except site NG-2 (lowest effect level) was the no effect level of the Ontario sediment quality guidelines. The COD/IL (0.02 ~ 0.20) and C/N (0.73 ~ 6.76) were less than 1 and 10, respectively. Organic matter in the study area produced naturally from aquatic organisms. Results of principal component analysis showed that fine sediments (very fine sand and silt) were significantly affected by organic matters (ignition loss, chemical oxygen demand, total organic carbon and total nitrogen). In addition, the highest organic matters content in the study area occurred at the site with the finest sediments (NG-2).

• 한국재료학회지
• /
• 제20권10호
• /
• pp.501-507
• /
• 2010

Changes in surface morphology and roughness of dc sputtered ZnO:Al/Ag back reflectors by varying the deposition temperature and their influence on the performance of flexible silicon thin film solar cells were systematically investigated. By increasing the deposition temperature from $25^{\circ}C$ to $500^{\circ}C$, the grain size of Ag thin films increased from 100 nm to 1000 nm and the grain size distribution became irregular, which resulted in an increment of surface roughness from 6.6 nm to 46.6 nm. Even after the 100 nm thick ZnO:Al film deposition, the surface morphology and roughness of the ZnO:Al/Ag double structured back reflectors were the same as those of the Ag layers, meaning that the ZnO:Al films were deposited conformally on the Ag films without unnecessary changes in the surfacefeatures. The diffused reflectance of the back reflectors improved significantly with the increasing grain size and surface roughness of the Ag films, and in particular, an enhanced diffused reflectance in the long wavelength over 800 nm was observed in the Ag back reflectors deposited at $500^{\circ}C$, which had an irregular grain size distribution of 200-1000 nm and large surface roughness. The improved light scattering properties on the rough ZnO:Al/Ag back reflector surfaces led to an increase of light trapping in the solar cells, and this resulted in a noticeable improvement in the $J_{sc}$ values from 9.94 mA/$cm^2$ for the flat Ag back reflector at $25^{\circ}C$ to 13.36 mA/$cm^2$ for the rough one at $500^{\circ}C$. A conversion efficiency of 7.60% ($V_{oc}$ = 0.93, $J_{sc}$ = 13.36 mA/$cm^2$, FF = 61%) was achieved in the flexible silicon thin film solar cells at this moment.

• 한국수산과학회지
• /
• 제34권3호
• /
• pp.245-253
• /
• 2001

곰소만 조간대에서 채취한 표층퇴적물에 대하여 입도분석을 수행하여 퇴적물의 조직 특성을 분석하였다. 코어 시료를 이용하여 퇴적물의 수리-역학적 특성을 실험적으로 도출하였으며, 퇴적물의 심도별 역학적 응력 및 과잉간극수압, 그리고 지반의 안정성을 수치해석적으로 분석하여 바지락 양식장 퇴적물의 거동 특성을 규명하였다. 곰소만 조간대내의 표층 퇴적물은 겨울에는 $5 \phi$의 조립 실트가 주를 이루는 단모드형을 나타내고, 여름에는 $5 \phi$의 조립 실트질 퇴적물에 $4 \phi$의 미세사질 퇴적물이 첨가된 경향을 보여준다 바지락 양식장의 퇴적환경은 평균 입도 $4\~5 \phi$범위, 모래함량 $50\%$ 미만, 니질 함량 $5\sim10\%$ 범위를 나타낸다. 퇴적양상은sandy silt이며, 분급도는 $1.0\sim2.0 \phi$를 나타내고, 왜도는 0.1-0.5의 범위에 포함되어 퇴적물의 퇴적 작용이 방해가 될만한 높은 에너지 상태가 지속되지 않는 환경이 바지락 양식에 양호한 것으로 조사되었다. 수치해석적 결과를 토대로 볼 때, 바지락 양식에 양호한 저질환경은 사질과 니질이 혼합되어 절대 투수계수가 $10^{-11}\sim10^{-12}m^2$ 범위인 경우로 사료되며, 수치해석 모델링 견과 니질 피복층의 두께가 4cm를 초과하게되면 바지락 서식에 대한 저질환경은 크게 저하되고 있는 것으로 고찰된다.

• 한국재료학회지
• /
• 제21권5호
• /
• pp.263-267
• /
• 2011

The present study was carried out to evaluate the microstructural and mechanical properties of cross-roll rolled pure copper sheets, and the results were compared with those obtained for conventionally rolled sheets. For this work, pure copper (99.99 mass%) sheets with thickness of 5 mm were prepared as the starting material. The sheets were cold rolled to 90% thickness reduction and subsequently annealed at $400^{\circ}C$ for 30 min. Also, to analyze the grain boundary character distributions (GBCDs) on the materials, the electron back-scattered diffraction (EBSD) technique was introduced. The resulting cold-rolled and annealed sheets had considerably finer grains than the initial sheets with an average size of 100 ${\mu}M$. In particular, the average grain size became smaller by cross-roll rolling (6.5 ${\mu}M$) than by conventional rolling (9.8 ${\mu}M$). These grain refinements directly led to enhanced mechanical properties such as Vickers micro-hardness and tensile strength, and thus the values showed greater increases upon cross-roll rolling process than after conventional rolling. Furthermore, the texture development of <112>//ND in the cross-roll rolling processed material provided greater enhancement of mechanical properties relative to the case of the conventional rolling processed material. In the present study, we systematically discuss the enhancement of mechanical properties in terms of grain refinement and texture distribution developed by the different rolling processes.

• 한국재료학회지
• /
• 제23권1호
• /
• pp.41-46
• /
• 2013

The microstructural evolution of AA1050/AA6061 complex aluminum alloy, which is fabricated using an accumulative roll-bonding (ARB) process, with the proceeding of ARB, was investigated by electron back scatter diffraction (EBSD) analysis. The specimen after one cycle exhibited a deformed structure in which the grains were elongated to the rolling direction for all regions in the thickness direction. With the proceeding of the ARB, the grain became finer; the average grain size of the as received material was $45{\mu}m$; however, it became $6.3{\mu}m$ after one cycle, $1.5{\mu}m$ after three cycles, and $0.95{\mu}m$ after five cycles. The deviation of the grain size distribution of the ARB processed specimens decreased with increasing number of ARB cycles. The volume fraction of the high angle grain boundary also increased with the number of ARB cycles; it was 43.7% after one cycle, 62.7% after three cycles, and 65.6% after five cycles. On the other hand, the texture development was different depending on the regions and the materials. A shear texture component {001}<110> mainly developed in the surface region, while the rolling texture components {011}<211> and {112}<111> developed in the other regions. The difference of the texture between AA1050 and AA6061 was most obvious in the surface region; {001}<110> component mainly developed in AA1050 and {111}<110> component in AA6061.

• 한국농공학회지
• /
• 제12권3호
• /
• pp.2003-2012
• /
• 1970

In order to the influence of grain size distribution on compressive strength and coefficient of permeability, unconfined compression test and permeability test were performed for seventy samples that have various grain-size distributions. Its results are as follows: 1. Maximum unconfined compressive strength appears at the dry side of optimum moisture content. 2. Unconfined compressive strength is proportional to the increase of percent passing of No. 200 sieve. 3. Precent of deformation in failure increases in proportion to the increase of percent passing of No. 200 sieve, and modulus of No. 200 sieve, and modulus of deformation also increases in proportion to percent passing of No. 200 sieve. 4. Unconfined compressive strength increases in proportion to uniformity coefficient, liquid limit and plastic index, but it decreases gradually according to the increase of coefficient of grading and classification area. 5. Maximum dry density decreases according to the increase of void ratio. 6. Coefficient of permeability decreases according to the increase of percent passing of No. 200 sieve, and when percent of No. 200 sieve, and when percent passing of No. 200 enlarged more than 40%, it becomes less than $10^{-6}cm/sec$ which is the limit of coefficient of permeability of core material for earth dam proposed by Lee. 7. Coefficient of permeability increases according to the increase of coefficient of grading, classification area and index of Talbot formula r, but it was rather decrease by the increase of uniformity coefficient. 8. Coefficient of permeability seems to depend on the size and the shape of the flow path which is a series of void to be concerned by the size and the proprton of soil grain, even though void ratios are same.

• 소성∙가공
• /
• 제33권3호
• /
• pp.178-184
• /
• 2024

In this study, we investigated the effects of extrusion ratio and extrusion temperature on the microstructure and tensile properties of extruded Mg-6Al-0.3Mn-0.3Ca-0.2Y (SEN6) alloy. As the extrusion ratio and temperature increase, dynamic recrystallization during extrusion is promoted, leading to the formation of a fully recrystallized microstructure with increased grain size. Additionally, the increases in extrusion ratio and temperature lead to texture strengthening, exhibiting a higher maximum texture intensity. The extruded materials contain three types of secondary phases, i.e., Al₈Mn₄Y, Al₂Y, and Al₂Ca, with irregular or polygonal shapes. The quantity, size, distribution, and area fraction of the second-phase particles are nearly identical between the two materials. Despite its larger grain size, the tensile yield strength of the material extruded at 450 ℃ and an extrusion ratio of 25 (450-25) is higher than that of the material extruded at 325 ℃ and an extrusion ratio of 10 (325-10), which is mainly attributed to the stronger texture hardening effect of the former. The ultimate tensile strength is similar in the two materials, owing to the higher work hardening rate in the 325-10 extrudate. Despite differences in grain size and recrystallization fraction, numerous twins are formed throughout the specimen during tensile deformation in both materials; consequently, the two materials exhibit nearly the same tensile elongation.

• 한국수자원학회논문집
• /
• 제46권1호
• /
• pp.87-97
• /
• 2013

본 연구에서는 HEC-RAS의 하상변동모형을 이용하여 고농도의 유사가 중소규모의 저수지에 유입하여 삼각주를 형성하는 과정을 유사의 입도분포를 고려하여 해석하였으며, 다음과 같은 결론을 얻을 수 있었다. 먼저, 삼각주의 시공간적인 분포와 년간 저수지에 퇴적되는 입도별 퇴사량을 합리적으로 예측할 수 있었다. 또한 저수지의 특정위치에서 특정시기에 어떤 입도의 유사가 주로 퇴적되는지를 합리적으로 예측할 수 있었다. 이러한 유사의 입도분포를 고려한 모의와 분석은 수자원관련 시설물의 계획 및 유지관리에 필요한 유용한 정보를 제공해 줄 수 있을 것으로 판단된다.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2000년도 추계학술대회 논문집
• /
• pp.212-216
• /
• 2000

ZnO varistors for distribution surge arrester (18kV, 5kA) were developed and tested microstructure and electrical characteristics. Microstructure of ZnO varistor was consisted of ZnO grain, spinel phase and Bi-rich phase. Average grain size of ZnO varistor was $\mu\textrm{m}$ Reference voltage and lightning impulse residual voltage of ZnO varistor exhibited a good haracteristics above 5.5kV and below 11.56kV, respectively. Consequently, discharge capacity which is the most important characteristics of ZnO varistor for surge arrester exhibited excellent properties above 70kA at twice high-current impulse test. Moreover, variation rate of reference voltage and lightning impulse residual voltage showed below 5% and 2% after high-current impulse test, respectively. Leakage current and watt loss of ZnO varistor will not increase during accelerated aging test at stress condition, such as 3.213kV/$115^{\circ}C$/1000h.

• 한국도로학회논문집
• /
• 제6권3호
• /
• pp.55-64
• /
• 2004

최대건조단위중량은 노상토 재료 특성으로서 매우 중요한 인자이다. 최대건조단위중량을 예측하는 기존의 모델들은 많은 변수를 포함하고 있어 다소 복잡해 보인다 본 논문에서는 사질토의 최대건조단위중량을 예측할 수 있는 간편한 식을 제안하였다. 이를 위해 36개 시료를 체분석하여 입도분포를 구하고, 다짐시험 한 후 그 결과를 회귀 분석하였다. 제안식은 변수로 노상토의 기하평균과 기하표준편차 또는 입도분포계수를 포함한다. 제안식의 검증을 위해 전국16개 지역의 채취 시료에 대한 최대건조단위중량의 실측치와 예측치를 비교한 결과 잘 맞는 것으로 밝혀졌다.