• Korean Journal of Materials Research
• /
• v.29 no.4
• /
• pp.264-270
• /
• 2019

As a case study on aspect ratio behavior, Kaolin, zeolite, $TiO_2$, pozzolan and diatomaceous earth minerals are investigated using wet milling with 0.3 pai media. The grinding process using small media of 0.3 pai is suitable for current work processing applications. Primary particles with average particle size distribution D50, ${\sim}6{\mu}m$ are shifted to submicron size, D50 ${\sim}0.6{\mu}m$, after grinding. Grinding of particles is characterized by various size parameters such as sphericity as geometric shape, equivalent diameter, and average particle size distribution. Herein, we systematically provide an overview of factors affecting the primary particle size reduction. Energy consumption for grinding is determined using classical grinding laws, including Rittinger's and Kick's laws. Submicron size is obtained at maximum frictional shear stress. Alterations in properties of wettability, heat resistance, thermal conductivity, and adhesion increase with increasing particle surface area. In the comparison of the aspect ratio of the submicron powder, the air heat conductivity and the total heat release amount increase 68 % and 2 times, respectively.

• Proceedings of the Korean Magnestics Society Conference
• /
• 2003.06a
• /
• pp.220-221
• /
• 2003

Equiatomic FePt and CoPt alloy thin films have received considerable attention as possible magnetic and magneto-optic recording because of their high magnetic anisotropy energy and high coercivity. The high coercivity in these thin films is due to the presence of finely dispersed ordered FePt phase mixed with disordered FePt phase. However, a high temperature treatment, either substrate heating during deposition or post annealing, is needed to obtain the ordered L1$\_$0/ phase with high value of magneto crystalline anisotropy. Recent microstructural studies on these films suggest that the average grain size ranges from 10-50 nm and the grains are magnetically coupled between each other. On the other hand, the ultrahigh-density magnetic recording media with low media noise imposes the need of a material, which consists of magnetically isolated grains with size below 10 nm. The magnetic grain isolation can be controlled by the amount of additional non-magnetic element in the system which determines the interparticle separation and therefore the interparticle interactions. Recently, much research work has been done on various non-magnetic matrices. Preliminary studies showed that the samples prepared in B$_2$O$_3$ and Carbon matrices have shown strong perpendicular anisotropy and fine grain size down to 4nm, which suggest these nanocomposite films are very promising and may lead to the realization of a magnetic medium capable of recording densities beyond 1 Tb/in$^2$. So, in this work, the effect of Carbon doping on the magnetic properties of FePt nanoparticles were investigated.

• Journal of Korean Ophthalmic Optics Society
• /
• v.11 no.2
• /
• pp.85-89
• /
• 2006

To research of the improved mechanical properties of materials for spectacle lens cutting, SiC and TiC were used as the main powder. Also, $Al_2O_3$ and $Y_2O_3$ was included as a sintering additive. The weight ratio of the alumina($Al_2O_3$) to yttria($Y_2O_3$) was set to 1:1. The materials for spectacle lens cutting were fabricated by hot-pressing at $1810^{\circ}C$ for 1h and subsequently annealed at $1860^{\circ}C$ for 3, 6 and 12h to initiated grain growth. The longer annealing time is, the bigger the grain size is. The microstructures were observed by scanning electron microscopy (SEM). The SEM images were quantitatively analyzed by image analysis (Image-Pro Plus, Media Cybernetics, Maryland, U.S.A.). Crack deflection by elongated SiC grains was most frequently observed as the dominant toughening mechanism. Crack deflection was generally observed for elongated SiC grains with aspect ratio(AR) > 2.5 and grain thickness < $2.3{\mu}m$. Crack bridging was also observed as one of the operating toughness mechanism.

• Journal of Mushroom
• /
• v.17 no.3
• /
• pp.107-112
• /
• 2019

This study was conducted to develop a healthy functional food material using mycelial extract of Phellinus sp. Jangsoo and GMPL48007 were selected as suitable strains because of good mycelial growth and high functionality. The highest total polyphenols and reducing power were observed in the Jangsoo strain and the radical scavenging was shown in GMPL48007. Among grains media, whole-grain wheat had the highest extraction yield from mycelia of selected strains; especially, the GMPL48007 strain showed the highest content of beta-glucan.

• The Journal of Engineering Geology
• /
• v.18 no.3
• /
• pp.311-319
• /
• 2008

Evaluation of an amplitude domain reflectometry (ADR) type soil moisture sensor as ThetaProbe ML2x using the response of frequency impedance was performed in a variety of soil porous media such as Jumunjin standard sand, weathered granite soil at Sangju area, and weathered gneiss soil at Jangsu area. The tested soils were classified with a dried condition and a wetted condition for comparing with soil volumetric water content under different installed depths of the measurement sensor. In the results the part of measurement rod including one signal rod and three shield rod 6cm in length was found to decrease the variation of measurement output voltage with insert 5cm over into the soil porous media. The measurement output voltage was verified to more stable output voltage under weathered granite soils and weathered gneiss soils contained the fine grain materials such as clay and silt minerals than the gradual grain material like as the standard sands. Therefore, measurement values by soil moisture sensor can be offered the more stable values when an contact volume between soil porous media and measurement sensor increase.

• Microbiology and Biotechnology Letters
• /
• v.9 no.4
• /
• pp.191-196
• /
• 1981

In order to utilize the Koryangju distillers' grain for the acetic acid fermentation, the extracting methods and effects of the extracts on the fermentations were investigated. The result obtained are as follows. 1. Cold extracting method by which the distillers grain is extracted with 3 times of water for 60 hours at room temperature was better than hot extracting method in terms of the fermentation rate and the quality of vinegar product. 2. Optimum conditions and some results of surface fermentation based on the medium added by the extracts are as follows, optimum amount of the extracts to be added to the medium is 20-30% of total media; acetic acid production rate at log phase was 0.16g/100$m\ell$, hr.; recovery was 91.17%; and the time of 40 hours was required for the completion of fermentation. 3. Organoleptic quality of the vinegar which is produced by adding the extracts was superior to two commercial products examined.

• Journal of Magnetics
• /
• v.5 no.4
• /
• pp.143-146
• /
• 2000

In this study, the magnetic properties of CoCrPt films (far longditudinal recording) on a novel VMn underlayer were measured and compared with similar films on conventional Cr underlayers. It was found that the VMn film had (200) preferred orientation and the lattice constant was about 0.2967 nm, which is slightly larger than that of the Cr film, 0.2888 m. The grain size of the VMn film was 9.8 nm at 30 m thickness, about 39% smaller than that of a similarly deposited Cr. The CoCrPt/VMn films showed higher coercivity in comparison with the CoCrPt/Cr films. The coercivity increase is attributed to the increased Co (11.0) texture, improved lattice matching between Co (11.0) and VMn (200), and lower stacking fault density. V or Mn must have diffused into the CoCrPt magnetic layer uniformly rather than preferentially along grain boundaries. This reduced Ms at higher substrate temperature.

• Proceedings of the Korean Magnestics Society Conference
• /
• 2000.09a
• /
• pp.352-362
• /
• 2000

In this study, effects of novel VMn underlayer on magnetic properties of CoCrPt/VMn longitudinal medium was studied and compared with those of CoCrPt/Cr medium. It was found that the VMn film had (200) preferred orientation and the lattice constant was about 0.2967 nm, which is slightly larger than that of the Cr, 0.2888 nm. The grain size of VMn film was 9.3 nm at 30 nm thickness, and this is about 38 % smaller than that of a similarly deposited Cr film. The CoCrPt/VMn films showed higher coercivity in comparison with the CoCrPt/Cr films. The coercivity increase seems to be attributed to the increased Co (11.0) texture, improved lattice matching between Co (11.0) and VMn (200), and lower stacking fault density. Mn must have diffused into the CoCrPt magnetic layer more uniformly rather than preferentially along grain boundaries this reduced Ms at higher substrate temperature

• Journal of the Korean Magnetics Society
• /
• v.11 no.3
• /
• pp.122-128
• /
• 2001

In this paper, we studied structural and magnetic properties of Ba-ferrite thin film deposited on Si(100) substrate with various underlayers. Ba-ferrite thin films with various underlayers were deposited by reactive RF/DC magnetron sputtering system at room temperature. various underlayers was reactive sputtered with O$_2$. After deposition, the thin films were annealed at 850 $^{\circ}C$ to get the crystallized sample. Underlayers were used to prevent interdiffusion from Ba-ferrite thin film to substrate. The growth of Ba-ferrite thin films was influenced by underlayers. Easy magnetization direction is in-plane. From these results the Ba-ferrite film with various underlayers can be used as longitudinal recording media.

• Proceedings of the Korean Magnestics Society Conference
• /
• 2007.05a
• /
• pp.40.2-40.2
• /
• 2007