• Journal of the Korean Crystal Growth and Crystal Technology
• /
• v.9 no.2
• /
• pp.231-239
• /
• 1999

The microstructure of ceramic composite has been found to be governed by the type and amount of the secondary phase, the sintering aid, and the sintering conditions such as sintering temperature, pressure and holing time. Moreover, tribological properties are strongly dependent on microsturcture of composite and operating conditions. In this study, silicon nitride with various amount of magnesia as a sintering aid were prepared and sintered by a hot pressing (HP) technique. Microstructure, mechanical properties (hardness, strength, and fracture toughness), and tribological properties in different environments of $Si_{3}N_{4}$ (in air, water, and paraffine oil) were investigated as a function of MgO content in $Si_{3}N_{4}$. As increasing the amount of MgO in $Si_{3}N_{4}$, the glassy phase in the grain boundaries enlarged the $\beta$-phase elongated grains, and also degraded the Hertzian contact damage resistance. Tribological behaviors in air was seemed to be determined by fracture toughness of $Si_{3}N_{4}$, and those in water and paraffin oil was seemed to be determined by hardness as well as strength. Since glassy grain-boundary phase (MgO) in $Si_{3}N_{4}$ expected to be reacted with water during sliding, such tribochemical reaction reduced wear. In paraffin oil under a higher applied load, the initial sliding dominated wear rate because of Hertzian contact damage.

• Journal of the Korean Vacuum Society
• /
• v.2 no.2
• /
• pp.199-208
• /
• 1993

The effect of nucleation free energy related to Si surface states on diamond film growth behavior has been studied. Ar first, the three kinds of diamond thin films (A, B, C) were deposited on various Si substrates (A-Si, B-Si, C-Si) whose surfaces were polished with 1 ${\mu}m$ diamond paste, 6 ${\mu}m$ Al_2O_3$ powder and 12 ${\mu}m$ Al_2O_3$ powder respectively. And then, relative nucleation free energy calculated is ${\Delta}G_{A-Si}<{\Delta}G_{B-Si}<{\Delta}G_{C-Si}$. Although there are some difference in grain size, shape and nucleated size, the thin films on A-Si and B-Si were diamond including a small amount of DLC which was confirmed by AES, SEM, XRD, and RHEED. Namely, the diamonds of films (B) were not nucleated in scratches but in dents and larger in grain size compare with the film (C) of which diamond sere nucleated not only scratches but also dents. And, the sphere diamond which is not general shape was grown on C-Si. After all, the sphere was turned out to be the diamond including much graphite as a result of the AES in situ depth profiling. Consequently, the diamond shape and quality grown on Si were Changed from the crystal which the (100) and (110) planes were predominent to the crystal in which (111) plane was predominent, and newt to sphere shape diamond including much graphite according as the nucleation free energy increases.

• Korean Journal of Agricultural and Forest Meteorology
• /
• v.15 no.4
• /
• pp.312-319
• /
• 2013

Our understanding of the sensitivities of crop responses to changes in carbon dioxide, temperature, and water is limited, which makes it difficult to fully utilize crop models in assessing the impact of climate change on future agricultural production. Genetic coefficients of CERES-Barley model for major domestic cultivars in South Korea (Olbori at Suwon, Albori at Milyang, Saessalbori at Iksan, and Samdobori at Jinju) were estimated from the observed data for daily weather and field trials for more than 10 years by using GenCalc in DSSAT. Data from 1997-2002 annual crop status report (Rural Development Administration, RDA) were used to validate the crop coefficients. The sitecalibrated CERES-Barley model was used to perform crop growth simulation with the 99 treatments of step change combinations in temperature, precipitation and carbon dioxide concentration with respect to the baseline climate (1981-2010) at four sites. The upper boundary corresponds to the 2071-2100 climate outlook from the RCP 8.5 scenario. The response surface of grain yield showed a distinct pattern of model behavior under the combined change in environmental variables. The simulated grain yield was most sensitive to $CO_2$ concentration, least sensitive to precipitation, and showing a variable response to temperature depending on cultivar. The emulated impacts of response surfaces are expected to facilitate assessment of projected climate impacts on a given cultivar in South Korea.

• Applied Biological Chemistry
• /
• v.11
• /
• pp.173-184
• /
• 1969

To elucidate the effect of Amo-1618(4-hydroxyl-5-isopropyl-2-methlphenyl trimethyl ammonium chloride, 1-piperidine carboxylate) known as a kind of growth retardant, on the growth, grain yield, increasing the efficiency of nitrogen fertilizer, behavior of mineral nutritions and the rate of phosphorus utilization, this experiment was conducted pot culture method in a vinyl house. Two nitrogen level, namely, practical nitrogen level(1 N) and three times nitrogen level(3 N) was made and labelled double-calcium-superphosphate $Ca(H_2P^{32}O_4)_2.\;2H_2O)$ as a source of radioactive phosphorus(P-32) was employed $80\;{\mu}c/pot$, respectively. Rice seedlings, variety 'Suwon No. 82', was transplanted to a 1/50,000 a china pot on June 13 in 1968. For treatment, at early stage of tillering, 10,000 ppm solution of Amo-1618 was foliar sprayed only one time. The Duncan's new mutiple-range test was adopted for statistical analysis evaluating experimental data at 5% level significance. The results obtained may be summarized as follows; 1) No significant difference was found among the treatments in plant height, but in plot of Amo-1618 treatment and 3 N level, number of tillers was significantly increased than that of others. 2) Weight of 10,000 kernels and seed-setting rate was also remarkably increased in same treatment above. 3) Grain yield per pot was significantly increased in Amo-1618 and 3 N level application. This results seemed to be due to the increased the factors on the yield. 4) Contents of nitrogen and phosphorus per cent in the grain was likewise increased in Amo-1618 and 3 N application. There is, however, no difference among treatments in the content of nitrogen and phosphorus in the leaves and culms of rice plants. 5) On the other hand, the contents of potassium and magnesium, no distinctly tendeny showed among treatments. 6) The rate of phosphorus utilization was significantly increased in the plot of Amo-1618 and 3 N application.

• Korean Journal of Soil Science and Fertilizer
• /
• v.45 no.6
• /
• pp.1094-1099
• /
• 2012

Green manure cultivation affects soil productivity and nutrient conservation in paddy soil at winter season. This study was to evaluate nitrogen behavior released from chinese milk vetch (CMV) as green manure by using stable $^{15}N$ trace during rice cultivation. The CMV used in the experiment was 29.9 of C/N ratio and 14.1 g N $kg^{-1}$ ($^{15}N$ 0.388 atom % excess) and was applied at rates of 10 and $30Mg\;ha^{-1}$ in pot of 1/2000a size. Rice growth and N uptake increased with higher levels of CMV application at harvesting stage. Among total N uptake, 14.6 and 26.8 % of nitrogen was released respectively from the two different rates of CMV application. Stable $^{15}N$ recovery by rice biomass was 60%, 54% to the $^{15}N$ input, respectively, of CMV application, which decreased in order of grain, root, and straw of rice biomass. Total N content in the soil after rice harvest was 1.9 and 2.1 g N $kg^{-1}$, respectively, with increasing N input by the different rates of CMV application and the rate of $^{15}N$ recovery derived from CMV in the soil was 3.8 and 4.8 %, respectively. N input by CMV application induced rice growth and productivity during rice cultivation. However, it might need proper managements to reduce N loss because about 36-41 % of nitrogen was lost from N input by CMV application.

• Journal of the Korean Crystal Growth and Crystal Technology
• /
• v.30 no.4
• /
• pp.150-155
• /
• 2020

Alumina (Al₂O₃) is mainly used as a structural ceramic material and to have good mechanical properties requires a dense microstructure. In commercial fabrication, the liquid phase sintering process is adjusted to reduce the sintering temperature of alumina. In this study, the effect of added amounts of cobalt oxide as a coloring agent on the microstructure and mechanical properties was investigated in the CaO-SiO₂-MgO-system liquid phase sintering of 92 % alumina at various sintering temperatures. When 11 wt% Co₂O₃ was added, a rearrangement of alumina particles, which is the main densification step in liquid phase sintering, occurred from a sintering temperature of 1200℃. Solution re-precipitation and coalescence steps followed from 1300℃ with the grain growth of alumina particles. The addition of excess Co₂O₃ and sintering temperatures above 1400℃ resulted in a decrease in sintered density and Vickers hardness, because of the low viscosity of the liquid phase. In 92 % alumina with the addition of 11 wt% Co₂O₃, a sintered density and Vickers hardness of 3.86 g/㎤ and 12.32 GPa, respectively, were obtained at a sintering temperature of 1350℃.

• Journal of the Korean Crystal Growth and Crystal Technology
• /
• v.22 no.1
• /
• pp.57-63
• /
• 2012

$Al_2TiO_5$ ceramics were sintered by a solid-state reaction. LAS (${\beta}$-spodumene) and $Fe_2O_3$ were added to the $Al_2TiO_5$ composition for enhancement of sintering behavior such as mechanical strength and thermal shock resistance. The sintered body was much densified by addition of LAS and $Fe_2O_3$ because LAS formed the liquid-phase and $Fe_2O_3$ suppressed the grain growth. We have systematically investigated the sintering characteristics, microstructures, mechanical properties, and thermal shock resistance according to the change of the amount of additive. When the additive of LAS (20 wt%)-$Fe_2O_3$ was added to $Al_2TiO_5$, it confirmed that superior mechanical properties of the fracture strength of over 120 MPa and the thermal shock resistance of over $1,200^{\circ}C$ were achieved.

• Journal of Advanced Marine Engineering and Technology
• /
• v.29 no.6
• /
• pp.654-661
• /
• 2005

Copper is a well known alloying element that is used to improve the resistance to general corrosion of stainless steel And also Cu cation have the anti-fouling effect to inhibit adhesion of the marine algae and shellfish to the surface of heat exchanger cooling pipe or outside wall of the ship, Therefore there are some anti-fouling methods such as anti-fouling Paint mixed with copper oxide or MGPS(Marine Growth Preventing System) by using Cu cation dissolved to the sea wather solution. Cu cation can be dissolved spontaneously by galvanic current due to Potential difference between Cu and cooling pipe of heat exchanger with Ti material, which may be one of the anti-fouling designs. In this study the effect of annealing heat treatment to galvanic current and Polarization behavior was investigated with a electrochemical points of view such as measurement of corrosion Potential, anodic polarization curve. cyclic voltammetric curve, galvanic current etc The grain size of the surface in annealed at $700^{\circ}C$ was the smallest than that of other annealing temperatures. and also the corrosion Potential showed more positive potential than other annealing temperatures. The galvanic current between Ti and Cu with annealed at $700^{\circ}C$ was the largest value in the case of static condition. However its value in the case of flow condition was the smallest than the other temperatures. Therefore in order to increase anti-fouling effect by Cu cation, the optimum annealing temperature in static condition of sea water is $700^{\circ}C$, however non- heat treated specimen in the case of flow condition may be desirable.

• Journal of the Korean Society for Precision Engineering
• /
• v.29 no.3
• /
• pp.273-278
• /
• 2012

$ZrB_2$ has a melting temperature of $3245^{\circ}C$ and a low density of $6.1\;g/cm^3$, which makes this a candidate for application to ultra-high temperature over $2000^{\circ}C$. Beside these properties, $ZrB_2$ has excellent resistance to thermal shock and oxidation compared with other non-oxide engineering ceramics. This paper reviewed briefly 2 research examples, which are related to densification and properties of $ZrB_2$-based ceramics for ultra-high temperature applications. In the first section, the effect of $B_4C$ addition on the densification and properties of $ZrB_2$-based ceramics is shown. $ZrB_2$-20 vol.% SiC system was selected as a basic composition and $B_4C$ or C was added to this system in some extents. With sintered bodies, densification behavior and hightemperature (up to $1400^{\circ}C$) properties such as bending strength and hardness are examined. In the second section, the effect of the SiC size on the microstructures and physical properties is shown. $ZrB_2$-SiC ceramics are fabricated by using various SiC sources in order to investigate the grain-growth inhibition and the mechanical/thermal properties of $ZrB_2$-SiC.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.29 no.4
• /
• pp.210-214
• /
• 2016

We investigated the sintering behavior and piezoelectric properties of lead-free $(K_{0.5}Na_{0.5})NbO_3$ ceramics co-doped with excess 0.01 mol ZnO and x mol $MnO_2$, where x was varied from 0 to 0.03. Excess $MnO_2$ addition was found to retard the grain growth and densification during sintering. However, 0.005 mol $MnO_2$ addition improved the piezoelectric properties of 0.01 mol ZnO added $(K_{0.5}Na_{0.5})NbO_3$ ceramics. The planar mode piezoelectric coupling coefficient, electromechanical quality factor, and piezoelectric constant $d_{33}$ of 0.01 mol ZnO and 0.005 mol $MnO_2$ added specimen were 0.40, 304, and 214 pC/N, respectively.