• Ocean and Polar Research
• /
• v.33 no.4
• /
• pp.421-434
• /
• 2011

Although thermal effluent from coastal power plants affects marine ecosystems, few studies have examined the spatiotemporal distribution of macrobenthic communities in a coastal area of Korea with thermal discharge. This study analyzed the species composition and abundance of a macrobenthic community in relation to environmental variables for a period of 1 year. In total 334 macrobenthic faunal species were collected; the mean density was 3,221 ind/$m^2$. The number of species and the density of macrobenthic fauna increased with distance from the thermal discharge site. Cluster analysis indicated that the macrobenthic community could be divided into two groups: group I in shallow (< 30 m deep) and group II in the outer areas (> 30 m deep). Group I showed the lowest species density and diversity. Four polychaetes, including Magelona japonica, Spiophanes bombyx, Scolotoma longifolia and Chaetozone setosa, all of which have been dominant species since 1987, exhibited higher mean densities in the area distant from the thermal discharge (the outer and north areas). Conversely, the warm-adapted and opportunistic species, such as the amphipods Urothoe convexa and Mandibulophoxus mai, the bivalve Felaniella sowerbyi, and the polychaete Rhynchospio sp., were more abundant in the thermal discharge region. The results of this study indicate that thermal effluent influences macrobenthic communities in the shallow area, while other environmental variables, such as depth, sediment grain size, and TOC, are more important determinants of the macrobenthic communities in deeper regions (> 30 m deep).

• Journal of environmental and Sanitary engineering
• /
• v.18 no.3 s.49
• /
• pp.35-42
• /
• 2003

The electric resistance and constant current were investigated on the nickel-thallium-phosphorus alloy deposits by electroless-plating. The Ni-Tl-P alloy deposits were achieved with a bath using sodium hypophosphit as the reducing agent and sodium citrate as the comlexing agent. The basic plating solution is composed of 0.1M NiSO$_4$, 0.005${\sim}$0.0IM Tl$_2$S0$_4$, 0.1${\sim}$O.2M sodium hypophosphite and 0.02${\sim}$O.IM sodium citrate and the plating condition were pH 5${\sim}$6, temperrature 80$_4$90${\circ}$C. The results obtained are summarized as follows: 1) The crystal structure of deposit was amorphous structure as deposited state, became microcrystallized centering on Ni(111) plane by heat treatment at 200${\circ}$C, and grew as polycrystalline Ni, Ni$_3$P, Ni$_5$p$_2$,Tl, etc. by heat treatment higher than 350${\circ}$C. The grain size of plated deposits was grown up to 28.3~42.0nm by heat treatment for 1hour at 500${\circ}$C. 2) The electrical resistivity showed a comparatively high value of 192.5$_4$208.3 ${\mu}$${\Omega}$Cm and its thermal stability was great with resistivity value less than 0.22% in the thermal surroundings of 200${\circ}$C. 3) Ni-Tl-P alloy deposit showed such good constant current-making-effect in the variation of electric voltage, heat treatment temperature, and the composition of the deposit that it can be put to practical use as the matter of constant current device.

• Economic and Environmental Geology
• /
• v.16 no.2
• /
• pp.65-78
• /
• 1983

This report deals with the sedimentological study of the littoral sand of beaches in the Busan area. The purpose of this report is to know the grain size, mineralogical composition, heavy mineral and clay mineral of the beach sands, and gravity measurements of the Nagdong River Deltas. 1) As a whole, the littoral sand of the beaches are composed of uniformly medium grained, moderately sorted and nearly symmetrical. The barrier sand of the Nagdong Estuary is composed of fine grained, well sorted and nearly symmetrical. 2) The littoral sand of the beaches is transported by saltation and rolling. The barrier sand of the Nagdong Estuary is transported by suspension and saltation. 3) In the littoral sand of the beaches, the ratio of feldspar to quartz is 1 :2.31 and in the barrier sand of the Nagdong Estuary 1:1.40. 4) The content of heavy mineral of samples ranges from 0.54 to 3.87 %. The principal heavy minerals are hornblende, pyroxene, epidote, garnet, leucoxene, zircon, apatite, magnetite, hematite and ilmenite with minor accessories of rutile and olivine. 5) The x-ray diffraction analysis of the clay mineral informs the existence of quartz, feldspar, kaolinite and montmorillonite. The montmorillonite is considered to have been derived from the alteration of acidic volcanic rocks. 6) To determine the depositional structure of the Nagdong Estuary, Gravity measurements were made. Free air anomaly ranges from 14.5 mgal to 33.5 mgal and Bouguer anomaly ranges from 14.3 to 23.5 mgal and both are closely related to the topography. According to the interpreted layer structure, the upper layer composing sand, silt and clay, the intermediate layer composing sand with gravel, the lower layer composing weathered and soft rock, and bed rock composing hornfels or andesite. 7) The depositional environments of the study, the littoral area is dominated by the marine environment and the Nagdong Estuary by the mixed environment.

• Journal of the Korean Society for Marine Environment & Energy
• /
• v.19 no.4
• /
• pp.247-258
• /
• 2016

Physical and acoustic properties of sediment on the southwestern Taean Penisula, the Yellow Sea, were studied using eight piston cores. The sediments in the study area are largely composed of sand which has been deposited with sea-level change after LGM(Last Glacial Maximum). After the sea-level rise, fine-grained sediments discharged from Keum River and neighboring coast area were deposited as muddy sand or sandy mud. Results of these sedimentary environment in this area, the texture of sediments are different from place to place with variable horizontal and vertical distribution of physical and acoustic properties. Correlations among the physical, geoacoustic properties, and mean grain size show slight deviations from those of the South Sea in spite of similar pattern. This is probably due to the differences in sedimentary environment, mineral composition, and measurement system.

• Asian-Australasian Journal of Animal Sciences
• /
• v.28 no.9
• /
• pp.1309-1316
• /
• 2015

In this paper, weight, carcass dressing, weights of the primary cuts, weights of the physical components of the primary cuts, and weights of the main commercial cuts of 66 $Purun{\tilde{a}}$ animals, of which 33 were bulls and 33 were steers were evaluated. These animals, with an average age of 19 months at the beginning of the experiment, were finished in a feedlot system during 116 days, and were fed with diets containing three levels of concentrate (0.8%, 1.1%, and 1.4% of body weight). The concentrate was formulated with 25% soybean meal, 73% ground corn grain, 1% of a mineral mix, and 1% of limestone. The interaction between sexual groups and the concentrate level was not significant for any of the variables. Likewise, no effect of the concentrate level was detected on the same variable traits. The bulls demonstrated higher hot carcass weights (265.1 vs 221.7 kg) and a higher proportion of forequarter (38.4% vs 36.1%) however the steers presented with higher proportions of side (19.7% vs 18.5%) and hindquarter (44.2% vs 43.1%). The bulls produced higher yields of muscle in the three primary cuts, there by resulting in higher yields of edible portions of the carcass. The bulls also produced higher weights of tenderloin, knuckle, topside, flat, eye round, rump, and rump cover. The finishing of young bulls in feedlot is to be recommended, since the animals produce carcasses with higher amounts of edible meat and higher yields of commercial cuts, thus allowing for a better price for the carcass. Low concentrate level could be used due to the lower cost of production for farmers.

• The Korean Journal of Malacology
• /
• v.30 no.3
• /
• pp.259-271
• /
• 2014

This study was conducted to investigate the impact of sand addition to an intertidal for the development of the Manila clam habitat on benthic community structure. For this, we focused on the spatio-temporal changes in the surface sediment condition and benthic community structure including Manila clam before and after the event. Study site was the lower part of Ojjeom tidal flat in Gonam-myeon, Taean-gun where sand added to on July 2010. We set three stations at each of sand adding area (experimental plot) and non sand-adding area (control plot) and did sampling works ten times from June 2010 to October 2011. Directly after the event, surface sediments changed to very coarse sand, but the state was not maintained over two months because of seasonal sedimentation and finally got back to the original grain sizes in eight months. The number of species and density were temporarily reduced right after the event and polychaetes such as Sternaspis scutata, Ampharete arctica were most negatively affected by the event. However, the number of species and density quickly recovered from the reduction in four to six weeks owing to the recolonization by the existing species and species in the vicinity of the plot. However, despite the recovery of ecological indies, species composition was continuously changed from one to another, thereby community structure stayed unstable condition, especially in some stations with finer sediment in their original condition. After sand addition, density of Manila clam was prominently increased at only one station with coarser sediment in its original condition.

• Journal of Powder Materials
• /
• v.21 no.5
• /
• pp.349-354
• /
• 2014

This study is a basic research for repair material production which manufactured a Cu repair coating layer on the base material of a Cu plate using kinetic spray process. Furthermore, the manufactured material underwent an annealing heat treatment, and the changes of microstructure and macroscopic properties in the Cu repair coating layer and base material were examined. The powder feedstocks were sphere-shaped pure Cu powders with an average size of $27.7{\mu}m$. The produced repair coating material featured $600{\mu}m$ thickness and 0.8% porosity, and it had an identical ${\alpha}$-Cu single phase as the early powder. The produced Cu repair coating material and base material displayed extremely high adhesion characteristics that produced a boundary difficult to identify. Composition analysis confirmed that the impurities in the base material and repair coating material had no significant differences. Microstructure observation after a $500^{\circ}C/1hr$. heat treatment (vacuum condition) identified recovery, recrystallization and grain growth in the repair coating material and featured a more homogeneous microstructure. The hardness difference (${\Delta}H_v$) between the repair coating material and base material significantly reduced from 87 to 34 after undergoing heat treatment.

• Journal of the Korean Applied Science and Technology
• /
• v.24 no.3
• /
• pp.238-245
• /
• 2007

$Eu^{3+}$ doped $YGdO_3$ phosphors particles which have fine size and narrow size distribution with non aggregated uniform morphology were prepared by solvent evaporation method for the improvement of emission efficiency. Several parameters have been investigated in this study such as the influences of composition ratio of host materials, calcination temperature, amount of activator, surfactant, pH and flux on the photoluminescence intensity, particle size and dispersion. $Eu^{3+}$ doped $YGdO_3$ phosphor presented a strong narrow band emission peak at 612nm. The maximum emission intensity of$YGdO_3:Eu^{3+}$ occurred when $Eu^{3+}$ concentration is 3wt% under vacuum ultra violet excitation. Prepared phosphors were found to have small round-shaped particles about 150nm in size. The addition of PVA as a surfactant inhibits the grain growth and the agglomeration of particles efficiently by reducing the oxygen bridge bonds. As the pH reduces, PL intensity increase due to reducing the formation of oxygen bridge bonds. The particles prepared from solvent evaporation method with 5wt% LiCl were found to have 120% PL intensity compare to particles prepared without LiCl flux.

• 한국초전도학회:학술대회논문집
• /
• v.9
• /
• pp.300-304
• /
• 1999

To tap the feasibility of exploiting the 2$^{nd}$ phases as flux-pinning centers in the (Bi,Pb)$_2Sr_2Ca_2CuO_{10}$ superconductor, the size and the distribution of the precipitates have been controlled by changing reaction temperature and time, oxygen partial pressure Po$_2$ and annealing condition. Various annealing heat treatments were also conducted on the as-received 61 filament Bi-2223 tapes with Bi$_{1.8}Pb_{0.4}Sr_2Ca_{2.2}Cu_3O_8$ starting composition and annealed specimen were analyzed with XRD, SEM, EDS and TEM.. The grain size of (Ca,Sr)$_2$(BiPb)O$_4$ or Bi$_{0.5}Pb_3Sr_2Ca_2CuO_{\delta}$ was controllable by optimizing the heat treatment condition and critical current density (J$_c$) showed dependence on the size of the 2$^{nd}$ phases.

• Korean Journal of Materials Research
• /
• v.22 no.1
• /
• pp.16-23
• /
• 2012

Research into the development of high strength (1 GPa) and superior formability, such as total elongation (10%), and stretch-flangeability (50%) in hot-rolled steel was conducted with a thermomechanically controlled hot-rolling process. To improve the overall mechanical properties simultaneously, low-carbon steel using precipitation hardening of Ti-Nb-V multimicroalloying elements was employed. And, ideal microstructural characteristics for the realization of balanced mechanical properties were determined using SEM, EBSD, and TEM analyses. The developed steel, 0.06C-2.0Mn-0.5Cr-0.2(Ti + Nb + V), consisted of ferrite as the matrix phase and second phase of granular bainite with fine carbides (20-50 nm) in both phases. The significant factor of the microstructural characteristics that affect stretch-flangeability was found to be the microstructural homogeneity. The microstructural homogeneity, manifest in such characteristics as low localization of plastic strain and internally stored energy, was identified by grain average misorientation method, analyzed by electron backscattered diffraction (EBSD) and hardness deviation between the phases. In summar, a hot-rolled steel having a composition 0.06C-2.0Mn-0.5Cr-0.2(Ti + Nb + V) demonstrated a tensile strength of 998 MPa, a total elongation of 19%, and a hole expansion ratio of 65%. The most important factors to satisfy the mechanical property were the presence of fine carbides and the microstructural homogeneity, which provided low hardness deviation between the phases.