• 한국세라믹학회지
• /
• 제32권12호
• /
• pp.1357-1368
• /
• 1995

Nasigels of composition Na0.75Zr2PSi2O12 and Na3Zr2PSi2O12 have been synthesized by the sol-gel technique using metal alkoxide precursors. The monolithic dry gels of Na0.75Zr2PSi2O12 with no crack have been prepared by the control of the shrinkage rte, but gels of Na3Zr2PSi2O12 were impossible to prepare without cracking. The gels treated up to 80$0^{\circ}C$ led to the formtion of glass but the glasses were converted to the crystalline phases at above this temperature. Crystaline phases precipitated from the Na0.75Zr2PSi2O12 glass were NASICON-like phase, Na2Si2O5, and free Zirconia. Phase that precipitated from the Na3Zr2PSi2O12 was only rhombohedral NASICON. For Na0.75Zr2PSi2O12 gels, framework of PO4 tetrahedra and SiO4(PO4) tetrahedra formed at low temperature but changed to that of SiO4 and SiO4(PO4) tetrahedras as it were crystallized. In the case of Na3Zr2PSi2O12 gel, framework of isolated PO4 and SiO4 tetrahedras formed at low temperature but changed to SiO4(PO4) tetrahedra framework which usually formed in the NASICON crystal after crystallization at high temperature. The gels treated up to 80$0^{\circ}C$ contained the residual water. The ionic conduction was attributed to the motion of proton and Na+ ion at low (up to 150~20$0^{\circ}C$) and high temperatures, respectively. As the temperature of heat treatment increased, ionic conductivity gradaully increased with the extent of precipitation of crystalline phase.

• 한국전산구조공학회논문집
• /
• 제27권2호
• /
• pp.121-128
• /
• 2014

본 논문에서는 새로운 형상의 GFRP 판으로 전단보강된 플랫 플레이트의 전단거동에 관하여 실험적으로 연구하였다. GFRP 판은 개구부가 있는 판의 형태로서 콘크리트와의 일체화 거동을 위하여 콘크리트에 매립하여 사용한다. 총 7개의 시험체에 대한 뚫림 전단실험을 수행하였고, 실험 변수로는 전단보강재의 종류와 전단보강량을 선택하였다. 실험결과를 시험체의 균열 및 파괴양상, 변형률, 하중변위곡선으로 분석하였다. 또한 GFRP 판으로 전단 보강된 플랫 플레이트의 ACI 318-11 기준식에 의한 계산값과 실험에 의한 결과값을 비교하였다. 실험 결과 GFRP 판이 플랫 플레이트의 전단보강재로써 뚫림 전단에 효과적으로 적용함을 확인하였다.

• 한국재료학회지
• /
• 제3권2호
• /
• pp.197-204
• /
• 1993

Plastic기 복합재료의 파괴거동에 미치는 원공크기오 판폭의 영향을 검토하기 위하여 단축인장시험을 행하였다. 점응력파손조건에서의 특성길이 $d_o$는 원공크기 및 판폭에 의존하며, 이를 기초로 파손강도를 예측하기 위한 수정 점응력 파손조건식을 제안하였다. 이 파손조건의 예측값은 실험값과 잘 일치하였다. 파손 강도는 원공선단의 손상비의 증가에 따라 증가하며, 이는 손상영역의 형성으로 인한 응력완화현상으로 설명되어 진다. 또한 불안정 파괴시의 최대균열길이 $a_c$는 특성길이 $d_o$의 약 2배의 값을 나타낸다. 파괴인성에 대응하는 한계에너지해방율 $G_c$의 변화는 원공선단의 손상영역의 증가에 의한 응력완화가 주요한 원인이라고 할 수 있다.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2005년도 하계학술대회 논문집 Vol.6
• /
• pp.369-370
• /
• 2005

LTCC (Low Temperature Cofired Ceramic) technology is one of technologies which can realize SIP (System-In-a-Package). In this paper realization of gas sensor using LTCC technology was described. In the conventional gas sensor structure, wire bonding method is generally used as an interconnection method whereas in the LTCC sensor structure, via was used for the interconnection. As sensing materials, $SnO_2$ was adopted. The effect of frit glass portion on the adhesion of the sensing material to the LTCC substrate and the electrical conductivity of the sensing material were analyzed. AgPd, PdO, Pt was added to the sensing material as an additive for improving the gas sensitivity and electrical conductivity and the effect of the amount of additives in the sensing material on the electrical conductivity was investigated. The effect of the amount of frit glass in the termination on the sensor performance, especially mechanical integrity, was considered and the crack initiation and propagation in the boundary between the sensing material and the termination was studied.

• 한국재료학회지
• /
• 제3권3호
• /
• pp.207-214
• /
• 1993

$Li_2O-Al_2O_3-SiO_3$계 결정화유리의 저온합성을 위하여 출방원료로서 각 해당 금속 알콕시드를 사용하였다. 알코올을 용매로 충분히 첨가하고, drying control chemical additive로 dimethy1 formamide를 적당량 첨가한 혼합용용액을 과잉의 물로 충분히 가수분해시킨 습윤겔을 저온으로 건고하여 균열이 없는 건조된 monolith겔을 합성하였다. 건조겔로부터 750-$950^{\circ}C$로 10시간 이상 소결하여 저열팽창성을 나타내는 ${\beta}$-eucrypytite(${\beta}$-quartz 고용체), $Li_2O\cdot Al_2O_3\cdot 3SiO_2$및 ${\beta}$-spodumene등의결정상을 석출시켰다.

• Elastomers and Composites
• /
• 제43권1호
• /
• pp.8-17
• /
• 2008

Styrene-butadiene rubber(SBR)은 내마모성, 상용성, 방진성이 우수 하지만, SBR은 주쇄의 불포화기때문에 오존에 의해 쉽게 손상을 받고 탄화수소에 쉽게 팽윤되어 점탄성을 잃어버려 고무제품으로서의 수명을 단축시킨다. 따라서, 본 연구의 목적은 SBR 고무의 이러한 단점을 보완하기 위함이다. 내오존성과 기계적물성을 개선시키기 위해서 내오존성이 우수한 ethylene-propylene-diene terpolymer(EPDM)을 다양한 비율로 블렌드하고, 방진제품으로써의 적합성을 고려하기 위하여 다양한 분석기술을 사용하여 경도, 열분해 온도, 모폴러지, 유리전이온도, 내오존성, 정적 스프링정수를 측정하였다. 본 실험을 통하여 SBR과 EPDM 블렌드의 조성변화에 따른 특성을 연구한 결과, SBR에 대하여 EPDM 30% 블렌드시 상용성이 우수하고, 내오존성이 증가하는 것을 알 수 있었다.

• 한국구조물진단유지관리공학회 논문집
• /
• 제13권4호통권56호
• /
• pp.126-136
• /
• 2009

분사식 FRP 보강 공법은 섬유(Fiber)와 수지(Resin)를 외부에서 혼합하여 요철이 많은 콘크리트 표면에 고속의 압축 공기로 랜덤하게 분사하여 기존 콘크리트 구조물을 보강하는 공법이다. 새로운 분사식 FRP 공법을 이용하여 구조물의 보강 성능을 평가하였다. 콘크리트 보 실험체에 대한 휨강도 실험을 수행하여 분사식 FRP의 최적물성치를 찾고 이 결과를 이용하여 PSC I형 거더 표준단면을 1/5로 축소한 구조물에 적용하여 실험을 하였다. 손상된 프리스트레스트 콘크리트에 적용한 결과 무보강보에 비하여 휨강도가 49.8% 증가하였고 사용상태의 거동이 개선되었으며, 보강에 의해 처짐 및 균열 제어에 효과적이었다. 결론적으로 분사식 FRP 공법의 보강 적용은 구조물의 성능 향상에 효과적이라고 할 수 있다.

• 대한치과보철학회지
• /
• 제28권1호
• /
• pp.165-191
• /
• 1990

Although a number of studies have been performed to assure that residual stress caused by a mismatch of alloy porcelain thermal expansion can contribute to clinical failure of a ceramometal restoration, the interactive influence of cooling rate on the magnitude of thermal expansion difference and on bond strength between them have not been extensively analyzed. The objective of this study was to determine the influence of cooling rate and the number of firing cycles on the expansion mismatch and the flexural failure resistance of metal porcelain strip. Tested alloys included one Pd-Ag alloy, one Ni-Cr-Be alloy with two kinds of porcelain, Vita and Ceramco. Metal specimens were cast into rods with a height of 13mm and a diameter of 5mm. Subsequently, the castings were subjected to scheduled firing cycles without porcelain. And the porcelain specimens after being fired were trimmed into a bar with a final dimension of $5{\times}5{\times}25mm$. Thermal expansions of the alloys and porcelains were measured by using a push rod or a differential dialometer respecitvely. Porcelain glass transition temperatures and expansion values were derived alloy-porcelain pairs were assessed by comparing expansion values of the components at a porcelain glass transition temperature. Calculations were made using combinations of a Ni-Cr alloy or Pd-Ag alloy with each of two porcelain products. Metal-porcelain strip specimens were subjected to four point loading in an Instron testing machine until crack occured at the metal-cramic interface at the time of sharp decrease of load on recorder. On the basis of this study, the following conclusions may be stated: 1. Regardless of the kinds of ceramometal combinations, both of calculated and experimental data revealed that the double fired specimens exhibited a significantly lower flexural strength. 2. By the rise of the amount of mismatch, bond strength were decreased. 3. Thermal expansion value of Pd-Ag alloys were higher than that of Ni-Cr alloys. 4. Expansion curves of metal were proportional to the increase of temperature and were not affected by the experimental conditions, however porcelains did not show the same magnitude of metal, and a shift of the glass transition temperature to higher temperatures was observed when cooled rapidly 5. Alloy-porcelain thermal compatibility appeared more dependent on the porcelain than the alloy.

• 대한치과보철학회지
• /
• 제29권1호
• /
• pp.111-137
• /
• 1991

Although a number of studies have been performed to assure that residual stress caused by a mismatch of alloy porcelain thermal expansion can contribute to clinical failure of a ceramometal restoratoin, the interactive influence of cooling rate on the magnitude of thermal expansion difference and on bond strength between them have not been extensively analyzed. The objective of this study was to determine the influence of cooling rate and the number of firing cycles on the expansion mismatch and the flexural failure resistance of metal porcelain strip. Tested alloys included one Pd-Ag alloy, one Ni-Cr-Be alloy with two kinds of porcelain, Vita and Ceramco. Metal specimens were cast into rods with a height of 13mm and a diameter of 5mm. Subsequently, the castings were subjected to scheduled firing cycles without porcelain. And the porcelain specimens after being fired were trimmed into a bar with a final dimension of 5 x 5 x 25mm. Thermal expansions of the alloys and porcelains were measured by using a push rod or a differential dialometer respectively. Porcelain glass transition temperatures and expansion values were derived alloy- porcelain pairs were assessed by comparing expansion values of the components at a porcelain glass transition temperature. Calculations were made using combinations of a Ni-Cr alloy or Pd-Ag alloy with each of two porcelain products. Metal- porcelain strip specimens were subjected to four point loading in an Instron testing machine until crack occured at the metal-cramic interface at the time of sharp decrease of load on recorder. On the basis of this study, the following conclusions may be stated : 1. Regardless of the kinds of ceramometal combinations, both of calculated and experimental data revealed that the double fired specimens exhibited a significantly lower flexural strength. 2. By the rise of the amount of mismatch, bond strength were decreased. 3. Thermal expansion value of Pd-Ag alloys were higher than of Ni-Cr alloys. 4. Expansion curves of metal were proportional to the increase of temperature and were not affected by the experimental conditions, however porcelains did not show the same magnitude of metal, and a shift of the glass transition temperature to higher temperatures was observed when cooled rapidly. 5. Alloy- porcelain thermal compatibility appeared more dependent on the porcelain than the alloy.

• Korean Chemical Engineering Research
• /
• 제50권3호
• /
• pp.562-566
• /
• 2012

본 논문에서는 세그먼트 관형 고체산화물 연료전지(SOFC)의 설계 및 제작과 특성 분석을 다루고 있다. 관형 세라믹 지지체는 압출 공정을 통하여 제작하였으며, NiO-YSZ 연료극과 YSZ 전해질은 담금 코팅법을 통해 세라믹 지지체에 코팅하였다. 코팅된 세라믹 지지체를 $1,350^{\circ}C$에서 5시간 동안 열처리하였으며, $10{\mu}m$ 미만의 치밀하고, 균열이 없는 YSZ 전해질 층을 얻을 수 있었다. 또한 열처리된 세라믹 지지체에 LSM-YSZ/LSM/LSCF로 구성된 다층 구조 공기극을 담금법으로 코팅하여 $1,150^{\circ}C$에서 열처리하였다. 세라믹 관형 지지체에 코팅된 세그먼트 SOFC 셀은 Ag-glass 연결재를 사용하여 전기적으로 직렬 연결하였으며, 수소연료 유량과 운전 온도에 따른 세그먼트 SOFC의 성능 변화를 측정하였다.