• 한국산학기술학회논문지
• /
• 제21권1호
• /
• pp.277-283
• /
• 2020

기계식 기어의 치를 영구자석으로 대체한 동심 마그네틱 기어에서 원주방향을 따라 놓인 모든 자석이 동력 전달에 관여하므로 감속비를 결정하는 자석의 극수비는 마그네틱 기어의 거동 특성에 큰 영향을 미친다. 본 논문에서는 극수비를 변화시켜가며 마그네틱 기어에서 생성되는 전달토크의 밀도, 동손을 고려한 토크의 효율, 코깅 특성을 포함한 토크의 품질 등을 유한요소 해석을 이용하여 비교 분석하였다. 구동측의 극수를 2극에서 5극까지 변화시킬 때 전달토크가 최대가 되는 최적의 극수비가 존재함을 확인하였으며 이는 모듈레이터를 통한 구동측 자기장의 필터링 성분에 직접적인 영향을 받다. 전달 효율 역시 와전류 생성 밀도와 자기장간에 비례특성이 있으므로 전달 토크 밀도와 유사한 경향을 나타내는 것을 알 수 있으며 낮은 기어비에서는 95% 이상의 효율을 보인다. 제한된 극수를 갖는 영구자석의 상호작용에 기인하는 코깅 특성은 일반적인 동기 모터에서와 같이 구동측 자석의 개수와 모듈레이터 치의 개수간의 최소공배수에 반비례하는 것을 확인할 수 있었다. 전달 토크 평가를 위해 실제 시험 모델이 제작되었고 실증시험이 진행되었다.

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 2008년도 추계학술대회 논문집
• /
• pp.61-62
• /
• 2008

• 한국마린엔지니어링학회:학술대회논문집
• /
• 한국마린엔지니어링학회 2012년도 전기공동학술대회 논문집
• /
• pp.270-270
• /
• 2012

• 한국산학기술학회논문지
• /
• 제14권11호
• /
• pp.5392-5395
• /
• 2013

환자 및 노약자 이동에 중요한 역할을 하고 있는 수 전동휠체어의 핵심부인 구동부를 새롭게 설계했다. 구동부는 고속모터와 다단기어 치형을 설계적용하고, 굽힘강도와 면압강도를 고려해 큰 추진력을 얻을 수 있도록 성능을 검증하였다. B-Type의 마찰판식 클러치 전자식 브레이크(다판 방식의 무여자 작동형)를 동 축상에 설치해, 큰 토크에도 급격한 제동이 가능하도록 했다. 본 연구에 설계된 다단치차 감속기를 수 전동휠체어 구동장치에 사용하므로서, 소형화, 경량화를 이루고 구동 효율이 기존제품보다 30% 향상된 구동부를 구성할 수 있었으며, 보수 및 관리의 용이성을 함께 추구했다.

• 한국기계가공학회지
• /
• 제13권5호
• /
• pp.1-7
• /
• 2014

In this paper the structural analysis of a planet carrier was carried out for the design optimization of a slewing reducer used in tower cranes. The stress changes of the planet carrier according to the tolerance of interference fit were investigated, and the strength was evaluated on the basis of the stress level. The analysis results showed that the tolerance of interference fit have an important influence on the stress level of the planet carrier. To guarantee the static safety of carrier, the tolerances of carrier pinhole and planet pin as well as loading level exerted on the planet carrier should be determined considered correctly.

• 한국기계가공학회지
• /
• 제13권1호
• /
• pp.115-120
• /
• 2014

Wind power is a type of clean energy source which does not produce carbon dioxide. The wind turbine industry is considered as a major growth industry in many countries. The main cause of wind turbine failure arises in the wind turbine gearbox, and the main type of damage occurs in the bearings and gears. Therefore, predictions of gear and bearing damage are very important to ensure the reliability of the wind turbine reducers used in these systems. In this research, in order to optimize the wind turbine reducer, a series of simulations and redesigns was done using the tool RomaxDesigner. The RomaxDesigner model was used to analyze the bearing life of the duty cycle for a 5 MW wind-turbine pitch drive and to calculate the load in operating states. The reducer was designed to satisfy the life requirement by analyzing bearing damage and calculating the stress values of the main parts of the reducer.

• 드라이브 ㆍ 컨트롤
• /
• 제16권3호
• /
• pp.33-41
• /
• 2019

This study presents the development of a lifetime test bench for the strain wave reducer which is a precision gear reducer of the robot to realize fault diagnosis and failure prognostics. To this end, the lifetime test bench was designed to detect the vertical forward/reverse direction rotation load. Through the lifetime test bench, it is possible to apply the same load spectrum from robot working scenarios. We developed a data integration gateway for fault data collection. Through the development of dedicated software for fault diagnosis and failure prognostics, these data from vibration, noise and temperature sensors were collected and analyzed along with the operation of the lifetime evaluation.

• 한국기계가공학회지
• /
• 제20권11호
• /
• pp.36-42
• /
• 2021

This study was conducted to analyze the effect of the gear specification and gear quality corresponding to the macro geometry on the gear transmission error. The two pairs of gears with large and small transmission errors were selected for calculation, and two pairs of gears were manufactured with different gear quality. The test gears were manufactured by two different gear specifications with ISO 5 and 8 gear quality, respectively. The transmission error measurement system consists of an input motor, reducer, encoders, gearbox, torque meter, and powder brake. To confirm the repeatability of the test results, repeatability was confirmed by performing three repetitions under all conditions, and the average value was used to compare the transmission error results. The transmission errors of the gears were analyzed and compared with the test results. When the gear quality was high, the transmission error was generally low depending on the load, and the load at which the decreasing transmission error phenomenon was completed was also lower. Even when the design transmission error according to the gear specification was different, the difference of the minimum transmission error was not large. The transmission error at the load larger than the minimum transmission error load increased to a slope similar to the slope of the analysis result.

• 한국생산제조학회지
• /
• 제20권6호
• /
• pp.830-836
• /
• 2011

Most of pitch/yaw reducers consist of several planetary geartrains. Planetary geartrains make gearboxes to be small and light, low noise and good efficiency. Most important thing in the planetary geartrain is load distribution on the gear tooth flank. In this study, the effect of output shaft bearings on the load distribution of gear tooth flank has been investigated. The commercial software was employed to compare the load distribution of two models depending on the bearing type. The spherical roller bearing(SRB) and the cylindrical roller bearing(CRB) were used as output shaft bearings in the $1^{st}$ model, and two taper roller bearings(TRB) were used in the $2^{nd}$ model. As a result, it was found that the $2^{nd}$ model. showed better performances on the load distribution of gear tooth flank, this results stated that the output shaft bearing system could be important consideration when designing reducers for wind turbine systems.

• 한국기계가공학회지
• /
• 제19권9호
• /
• pp.116-121
• /
• 2020

In recent times, fuel economy enhancement and environmental regulation compliance have become the main topics of interest in the automobile industry. Electric vehicles are desirable alternatives to the existing cars that employ internal combustion engines. Specifically, electric vehicles are equipped with inverters, motors, and a gearbox instead of engines and transmission mechanisms. The gearbox is a key component, used to transmit power from the electric motor to the wheel. Therefore, the design of the gearbox is critical. However, most engineers design gears based only on their experience because no standards pertaining to the design factor exist, other than those for the gear ratios. To overcome this problem, the structural stabilities must be examined considering the design factors of the gears. In this study, we considered the module and number of teeth as the main factors. The constraints corresponded to the final gear ratio and fixed distance between each axle of the shafts. Moreover, a structural analysis was conducted, and the variation trend of the maximum equivalent stress against changes in the gear module and number of teeth was examined. By performing such an analysis, the structural stability in the design of a gear system could be effectively investigated.