• Journal of the Institute of Electronics Engineers of Korea SD
• /
• v.37 no.11
• /
• pp.1-8
• /
• 2000

In this paper, the dependence of interconnect line-induced delay time on the size of CMOSFET gate width is characterized. In case of capacitance dominant interconnect line, the total delay time decreases as transistor size increases. However, there exists a transistor size for minimum total delay time when both of resistance and capacitance of interconnect line become larger than those of transistor. The optimum transistor size for minimum total delay time is obtained using an analytic equation and the experimental results showed good agreement with the calculation.

• Journal of IKEEE
• /
• v.19 no.1
• /
• pp.110-117
• /
• 2015

In this paper, a novel trench power MOSFET using a Separate-W-gated technique MOSFET (SWFET) is proposed. Because the SWFET has a very low $Q_{GD}$ compared to other forms of technology, it can be applied to high-speed power systems. The results found that the SWFET-applied $Q_{GD}$ was decreased by 40% when compared to simply using the more conventional trench gate MOSFET. $C_{ISS}$ (input capacitance : $C_{GS}+C_{GD}$), $C_{OSS}$ (output capacitance : $C_{GD}+C_{DS}$) and $C_{RSS}$ (reverse recovery capacitance : $C_{GD}$) were improved by 24%, 40%, and 50%, respectively. The switching characteristics of the inverter circuit shows a 24.9% enhancement of reverse recovery time, and the power efficiency of the DC-DC buck converter increased by 14.2%. In addition, the proposed SWFET does not require additional process steps and There was no degradation in the electrical performance of the current-voltage and on-resistance.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.33 no.2
• /
• pp.109-113
• /
• 2020

A power device is a component used as a switch or rectifier in power electronics to control high voltages. Consequently, power devices are used to improve the efficiency of electric-vehicle (EV) chargers, new energy generators, welders, and switched-mode power supplies (SMPS). Power device designs, which require high voltage, high efficiency, and high reliability, are typically based on MOSFET (metal-oxide-semiconductor field-effect transistor) and IGBT (insulated-gate bipolar transistor) structures. As a unipolar device, a MOSFET has the advantage of relatively fast switching and low tail current at turn-off compared to IGBT-based devices, which are built on bipolar structures. A superjunction structure adds a p-base region to allow a higher yield voltage due to lower R_DS (on) and field dispersion than previous p-base components, significantly reducing the total gate charge. To verify the basic characteristics of the superjunction, we worked with a planar type MOSFET and Synopsys' process simulation T-CAD tool. A basic structure of the superjunction MOSFET was produced and its changing electrical characteristics, tested under a number of environmental variables, were analyzed.

• Electrical & Electronic Materials
• /
• v.7 no.1
• /
• pp.57-63
• /
• 1994

Aluminum oxide($Al_2{O_3}$) offers some unique advantages over the conventional silicon dioxide( $SiO_{2}$) gate insulator: greater resistance to ionic motion, better radiation hardness, possibility of obtaining low threshold voltage MOS FETs, and possibility of use as the gate insulator in nonvolatile memory devices. We have undertaken a study of the dielectric breakdown of $Al_2{O_3}$ on Si deposited by GAIVBE technique. In our experiments, we have varied the $Al_2{O_3}$ thickness from 300.angs. to 1400.angs. The resistivity of $Al_2{O_3}$ films varies from 108 ohm-cm for films less than 100.angs. to 10$_{13}$ ohm-cm for flims on the order of 1000.angs. The flat band shift is positive, indicating negative charging of oxide. The magnitude of the flat band shift is less for negative bias than for positive bias. The relative dielectric constant was 8.5-10.5 and the electric breakdown fields were 6-7 MV/cm(+bias) and 11-12 MV/cm (-bias).

• Journal of Magnetics
• /
• v.19 no.2
• /
• pp.197-204
• /
• 2014

A transcranial magnetic stimulation device is a complicated appliance that employs a switching power device designed for discharging and charging a capacitor to more than 1 kV. For a simple transcranial magnetic stimulation device, this study used commercial power and controlled the firing angle using a Triac power device. AC 220V 60 Hz, the power device was used directly on the tanscranial magnetic stimulation device. The power supply device does not require a current limiting resistance in the rectifying device, energy storage capacitor or discharge circuit. To control the output power of the tanscranial magnetic stimulation device, the pulse repetition rate was regulated at 60 Hz. The change trigger of the Triac gate could be varied from $45^{\circ}$ to $135^{\circ}$. The AVR 182 (Zero Cross Detector) Chip and AVR one chip microprocessor could control the gate signal of the Triac precisely. The stimulation frequency of 50 Hz could be implemented when the initial charging voltage Vi was 1,000 V. The amplitude, pulse duration, frequency stimulation, train duration and power consumption was 0.1-2.2T, $250{\sim}300{\mu}s$, 0.1-60 Hz, 1-100 Sec and < 1 kW, respectively. Based on the results of this study, TMS can be an effective method of treating dysfunction and improving function of brain cells in brain damage caused by ischemia.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2005.07a
• /
• pp.195-196
• /
• 2005

In recent years, as the needs of MOS's a high quality is desired to get the superior electrical characteristics and reliability on MOSFET. As an alternative gate dielectric have drawn considerable alternation due to their superior performance and reliability properties over MOSFET, 2'nd silicidation formation process has been proposed as a dielectric growth/annealing process. In this study the author observed process characteristics on MOS structure. In view points of the process characteristics of MOS capacitor, the oxygen & polysilicon was analyzed by SIMS analysis on l'st & 2'nd Ti process, the oxygen and Si2 contents[Count/sec] of 1.5e3 & 3.75e4 on l'st process and l.1e3 & 2.94e4 on 2'nd process, the Ti contents' of 8.2e18 & 6.5e18 on 1'st and 2'nd process. The sheet resistance[$\Omega/sq.$] was 4.5 & 4.0, the film stress[dyne/cm 2] of 1.09e10 & 1.075e10 on l'st and 2'nd process. I could achieved the superior MOS characteristics by 2'nd silicidation process.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2010.02a
• /
• pp.248-248
• /
• 2010

CMOS 축소화가 32nm node를 넘어서 지속적으로 진행되기 위하여 FinFET, Surround Gate and Tri-Gate와 같은 Fully Depleted 3-Dimensional 소자들이 SCE를 다루기 위해서 많이 제안되어 왔다. 하지만 소자의 축소화를 진행함에 있어서 좁고 균일한 patterning을 형성하는 것과 동시에 낮은 Extension Region과 Contact Region에서의 Series Resistance을 제공하여야 하고 Source/Drain Contact Formation을 확보하여야 한다. 그리고 소자의 축소화가 진행됨으로써 Silicide의 응집현상과 Source/Drain Junction의 누설전류에 대한 허용범위가 점점 엄격해지고 있다. ITRS 2005에 따르면 32nm CMOS에서는 Contact Resistivity가 대략 $2{\times}10-8{\Omega}cm2$이 요구되고 있다. 또한 Three Dimensional 소자에서는 Fin Corner Effect가 Channel Region뿐만 아니라 S/D Region에서도 중대한 영향을 미치게 된다. 따라서 본 논문에서 제시하는 Novel S/D Contact Formation 기술을 이용하여 Self-Aligned Dual/Single Metal Contact을 이루어Patterning에 대한 문제점 해결과 축소화에 따라 증가하는 Contact Resistivity 문제점을 해결책을 제시하고자 한다. 이를 검증하기3D MOSFET제작하고 본 기술을 적용하고 검증한다. 또한 Normal Doping 구조를 가진3D MOSFET뿐만 아니라 SCE를 해결하기 위해서 대안으로 제시되고 있는 SB-MOSFET을 3D 구조로 제작하고, 이 기술을 적용하여 검증한다. 그리고 Silvaco simulation tool을 이용하여 S/D에 Metal이 Contact을 이루는 구조가 Double type과 Triple type에 따라 Contact Resistivity에 미치는 영향을 미리 확인하였고 이를 실험으로 검증하여 소자의 축소화에 따라 대두되는 문제점들의 해결책을 제시하고자 한다.

• Journal of the Institute of Electronics and Information Engineers
• /
• v.53 no.8
• /
• pp.39-48
• /
• 2016

In this paper, we propose thermal resistance compact model of FinFET structure that has hexagon shaped source/drain. The heating effect and thermal properties were increased by reduced size of the device, and thermal resistance is an important factor to analyze the effect and the properties. The heat source and each contact that is moved heat out were set up in transistor, and domain is divided by the heat source and the four parts of contacts : source, drain, gate, substrate. Each contact thermal resistance model is subdivided as a easily interpretable structure by analyzing the temperature and heat flow of the TCAD simulation results. The domains are modeled based on an integration or conformal mapping method through the structure parameters according to its structure. First modeled by analyzing the thermal resistance to a single fin, and applying the change in the parameter of the channel increases to improve the accuracy of the thermal resistance model of the multi-fin/ finger. The proposed thermal resistance model was compared to the thermal resistance by analyzing results of the 3D Technology CAD simulations, and the proposed total thermal resistance model has an error of 3 % less in single and multi-finl. The proposed thermal resistance model can predict the thermal resistance due to the increase of the fin / finger, and the circuit characteristics can be improved by calculating the self-heating effect and thermal characterization.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.16 no.5 s.96
• /
• pp.482-487
• /
• 2005

In this paper, we propose the control method of output impedance of each cascode unit cell of distributed amplifier by connecting varactors in the gate-terminal of common gate. Compared to common source unit cell, cascode unit cell has many advantages such as high gain and high output impedance as well as negative resistance loading. But if the transistor model which is used in design is inaccurate and process parameter is changed, oscillation sometimes can occur at band edge in which the gain start to drop. Therefore, we need control circuit which can prevent oscillation, although the circuit has already fabricated, and varactor connected to gate-terminal of common gate of cascode gain cell can play that part. Measured result of fabricated distributed amplifier shows the capability of contol of gain characteristic by adjusting of value of varactors, this can guarantee the stability of the circuit. The gain is $8.92\pm0.82dB$ over 49 GHz, the group delay is $\pm9.3 psec$ over 41 GHz. All transistor which has $0.15{\mu}m$ gate length is GaAs based p-HEMT, and distributed amplifier is put together with 4 stages.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2013.02a
• /
• pp.543-543
• /
• 2013

Thin-film transistors (TFTs) based on oxide semiconductors have been regarded as promising alternatives for conventional amorphous and polycrystalline silicon TFTs. Oxide TFTs have several advantages, such as low temperature processing, transparency and high field-effect mobility. Lots of oxide semiconductors for example ZnO, SnO2, In2O3, InZnO, ZnSnO, and InGaZnO etc. have been researched. Particularly, zinc-tin oxide (ZTO) is suitable for channel layer of oxide TFTs having a high mobility that Sn in ZTO can improve the carrier transport by overlapping orbital. However, some issues related to the ZTO TFT electrical performance still remain to be resolved, such as obtaining good electrical contact between source/drain (S/D) electrodes and active channel layer. In this study, the bottom-gate type ZTO TFTs with staggered structure were prepared. Thin films of ZTO (40 nm thick) were deposited by DC magnetron sputtering and performed at room temperature in an Ar atmosphere with an oxygen partial pressure of 10%. After annealing the thin films of ZTO at $400^{\circ}C$ or an hour, Cu, Mo, ITO and Ti electrodes were used for the S/D electrodes. Cu, Mo, ITO and Ti (200 nm thick) were also deposited by DC magnetron sputtering at room temperature. The channel layer and S/D electrodes were defined using a lift-off process which resulted in a fixed width W of 100 ${\mu}m$ and channel length L varied from 10 to 50 ${\mu}m$. The TFT source/drain series resistance, the intrinsic mobility (${\mu}i$), and intrinsic threshold voltage (Vi) were extracted by transmission line method (TLM) using a series of TFTs with different channel lengths. And the performances of ZTO TFTs were measured by using HP 4145B semiconductor analyzer. The results showed that the Cu S/D electrodes had a high intrinsic field effect mobility and a low effective contact resistance compared to other electrodes such as Mo, ITO and Ti.