• 설비공학논문집
• /
• 제27권9호
• /
• pp.491-496
• /
• 2015

Generally, the phase of the refrigerants that circulate in air-conditioning systems is repeatedly changed from liquid to gas and from gas to liquid. In vapor-compression refrigeration, the refrigerant at the inlet of the evaporator is in a gas-liquid two-phase state; therefore, to enhance the heat-transfer performance of the evaporator, the even distribution of the refrigerant across multiple passages of the evaporator is essential. Unlike the distribution of a single-phase refrigerant, multi-phase distribution requires further considerations. It is known that the multi-phase distribution at the outlet of the distributor is affected by factors such as the operating condition, the distributor's shape, and the insertion depth of the outlet pipes; here, the insertion depth of the outlet pipes is especially significant. In this study, for a cylindrical distributor with a 90-degree bend entrance and three outlet pipes, the flow uniformity at the outlet pipes was numerically tested in relation to variations of the insertion depth of the outlet pipes.

• 한국재료학회지
• /
• 제13권3호
• /
• pp.160-168
• /
• 2003

The co-firing processes for the supported type planar solid oxide fuel cell were investigated. A flat cell of $7.7${\times}$10.8\textrm{cm}^2$ was fabricated successfully by the co-firing process, in which green films were co-sintered in the forms of two layers of anode/electrolyte or of three layers of anode/electrolyte/cathode with gas distributor. A co-fired cell of two layers yielded a power of 200 ㎽/$\textrm{cm}^2$ at 608 ㎷. Its performance loss was mainly due to iR drop in the anodic gas distributor, which was attributed to poor contact between anodic gas distributor and current collector. The performance in the co-fired cell of three layers was much lower than that of two layers, which resulted from the large iR drop and activation overvoltage at the cathodic side. In the co-fired cell of two layers, the impedance analysis indicated that the performance decay during cell operation is due to both anode overvoltage and iR drop at anode side. Also the electrode reaction of the co-fired two layers' cell is considered to be controlled by activation overvoltage within the low current of 50 ㎃.

• 한국수소및신에너지학회논문집
• /
• 제27권1호
• /
• pp.29-35
• /
• 2016

It is important to uniformly supply the fuel gas into the reaction activity area in polymer electrolyte membrane fuel cell (PEMFC). Recent studies have shown that the cell performance can be significantly improved by employing metal foam gas distributor as compared with the conventional bipolar plate types. The metal foam gas distributor has been reported to be more efficient to fuel transport. In this study, three-dimensional computational fluid dynamics (CFD) simulations have been performed to examine the effects of metal foam flow field design on the fuel supply to the reaction site. Darcy's law is used for the flow in the porous media. By solving additional advection equation for fluid particle trajectory, the gas transport has been visualized and examined for various geometrical configuration of metal foam gas distributor.

• 한국전산유체공학회:학술대회논문집
• /
• 한국전산유체공학회 2010년 춘계학술대회논문집
• /
• pp.567-570
• /
• 2010

With continuously increasing flat panel display size, uniformity of thin film deposition has been drawing more attentions and associated fabrication methodologies are being actively investigated. Since the convective flow field of mixture gas plays a significant role for deposition characteristics of thin film in an APCVD system, it is greatly important to maintain uniform distribution and consistent concentration of mixture gas species. In this paper, computational study has been performed for the improvement of flow uniformity of mixture gas in an APCVD reactor during thin film deposition process. A diffuser slit has bee designed to spread the locally concentrated gas flow exiting from the flow distributor. A uniform flow distributor has been developed which has less dependency on operating conditions for global flow uniformity

• 한국대기환경학회지
• /
• 제25권5호
• /
• pp.402-409
• /
• 2009

Sodium bicarbonate ($NaHCO_3$) was used as a reactant for the removal of acid gases from a waste incinerator. The removal efficiencies of HCl and $SO_x$ were tested with a reactant mixing apparatus and a distributor installed at the bag filter inlet. It was shown that the stoichiometric ratio of $NaHCO_3$ to the acid gases which allows a removal of over 90% for both HCl and $SO_2$ was about 1.2. When a reactant mixing apparatus was installed on the duct, the removal efficiencies of HCl and $SO_2$ at the end of the duct were increased by approximately 1.5 and 3 times respectively, compared to when the apparatus was not installed. At the end of the bag filter, the removal efficiencies of the both were as high as 98% with a stoichiometric ratio of 1.35. Installing a reactant mixing apparatus on the duct and a distributor at the entrance of the bag filter and using $NaHCO_3$ as a reactant helped overcome the problem of low removal efficiencies of acid gases by dry scrubbing.

• 공업화학
• /
• 제16권5호
• /
• pp.603-608
• /
• 2005

본 연구는 zinc titanate를 탈황제로 사용하는 유동층 탈황공정에서 고체 입자 마모특성을 고찰하는 것을 목표로 내경 0.035 m, 높이 1.34 m의 기체유동층 실험장치에서 수행되었다. 다공판 분배기에서 고속 분사 제트와 유동층 내부의 기포요동이 입자마모의 주요 원인으로 사료되었다. 탈황제의 마모속도가 작아서 회분식 측정결과가 연속식 유동층에 근사하게 적용될 수 있는 조건에서 수행되었다. 탈황공정에서 주요 변수인 기체유속, 온도, 압력, 층물질량의 변화에 따른 AI(attrition index)와 CAI(corrected attrition index)를 측정하였다. AI(5), CAI(5)는 층 무게가 증가함에 따라 감소하였다. 입자는 일정기간 충격에 의한 피로현상이 있은 후 마모되는 것으로 판단되었다. AI와 CAI는 기체속도, 상대습도, 압력이 증가함에 따라, 온도가 감소함에 따라 증가하였다. 입자마모는 주로 제트에 의하여 일어났으며 절단(fragmentation)보다 마쇄(abrasion)에 의하여 더 많은 미분입자가 발생하였다.

• 전기화학회지
• /
• 제5권1호
• /
• pp.7-12
• /
• 2002

염수 전해 공정에서 산소음극형 가스화산전극의 적용에 대해 연구, 조사하였다. 가스확산전극은 반응층, 가스확산층, 급 전체로 구성된다. 반응층은 친수성 카본블랙, 소수성 카본블랙, PTFE(polytetrafluoroethylene), 은거울반응이나 함침법에 의해 담지된 은 촉매로 제조하였다. 가스확산충은 소수성 카본블랙과 PTFE로 제조되며, 반응층 내에 사용되는 급전체는 Ni망을 사용하였다. 실험에 의하면 함침법에 의해 Ag촉매를 반응충 카본에 담지시켜 제작된 전극$(Ag\;10wt\%$,바인더 $20wt\%)$이 산소음극 과전압이 약 700mv, 전해조에 장착하여 측정한 전해전압(전해 조건이 $80^{\circ}C,\;32wt\%$ 가성소다 그리고 $300 mA/cm^2$의 전류 밀도)이 약 2.2V로 가장 우수한 결과를 나타내었다. 이는 기존 공정의 전해전압 3.4V에 비해 $30\%$이상 저감된 결과이다. 또한 개발된 가스확산 전극은 염수 분해용 전해 공정에서 3개월 연속 운전이 가능하였다.

• 대한기계학회논문집B
• /
• 제35권8호
• /
• pp.805-814
• /
• 2011

알루미늄 플레이트-핀 열교환기는 석유 및 가스 처리공정에서 널리 사용되고 있다. 알루미늄 플레이트-핀 열교환기의 성능은 각 유체의 헤더 및 분배기에서의 분배 성능에 의하여 크게 영향을 받는다. 본 연구에서는 CFD(Computational fluid dynamics)를 이용하여 알루미늄 플레이트-핀 열교환기의 측면 입구 형태의 분배기를 모델링하고, 입구 조건과 형상비의 변화에 따른 상대 및 절대 불균등 분배도를 고찰하여 최적 분배기 형상비를 제시하였다.

• 한국정보통신학회논문지
• /
• 제6권1호
• /
• pp.89-98
• /
• 2002

본 연구에서는 광계측 기술을 이용하여 배전자동화 개폐기 내에서 발생하는 전자 계측장치의 절연문제 및 측정오차의 문제점을 개선하기 위하여 배선자동화개폐기 내장형 광전류 및 광전압센서를 연구하였다. 자기광학 효과(magneto optic effect)인 페러데이효과(Faraday effect)를 이용하여 최적의 광전류 센서를 설계 제작하여 높은 전류까지 선형성을 유지시키고 다른 상의 전류에 대한 유도현상을 최소로 하기 위해 순철 코아를 사용하여 광전류 센서를 일체화시켜 설계 제작하였다. 설계내에서 결정의 굴절률 및 방위각의 변화에 의해 생기는 전기광학효과(electrooptic effect)인 포켈스 효과(pockels effect)를 이용하여 광전압센서를 구성하였으며 배전 자동화용 개폐기의 협소한 내부구조를 고려하여 공간전계방식을 채택하였다. 또한 다심의 광섬유를 개폐기와 외부의 신호처리 단말기와 연결하기 위하여 기밀형 멀티 광커넥터를 설계 자작하여 접속 손실 및 가스 누설 시험을 하였다. 전기적 특성시험에서 광 전류센서에서는 인가 전류에 대한 선형 특성은 20A 에서 700A까지 변동 오차 2.5% 이내의 선형성을 유지하였으며, 광전압센서에 있어서 인가 전압에 대한 선형 특성은 6.6kV에서 19.8kV까지 거의 변동 오차가 1% 이내로 우수한 선형 특성을 나타냈다.

• 한국수소및신에너지학회논문집
• /
• 제31권6호
• /
• pp.614-621
• /
• 2020

Recently, as the fine dust is increased and the emission regulations of diesel engines are strengthened, interest in diesel soot filtration devices is rapidly increased. In particular, there is a demand for technology development for higher efficiency of diesel exhaust gas after-treatment devices. As part of this, many studies conducted to increase the exhaust gas treatment efficiency by improving the flow uniformity of the exhaust gas in the DPF and reducing the pressure drop between the inlet and outlet of disel particle filter (DPF). In this study, computational fluid dynamics (CFD) simulation was performed when exhaust gas flows into the canning reduction device equipped with a 13" asymmetric DPF in order to maintain the flow uniformity in the diesel exhaust system and reduce the pressure. In particular, a study was conducted to find the geometry with the smallest pressure drop and the highest flow uniformity by simulating the DPF I/O ratio, exhaust gas temperature, inlet-outlet pressure and flow uniformity according to the geometry and hole size of distributor.