• Proceedings of the Korean Society For Composite Materials Conference
• /
• 2002.05a
• /
• pp.9-12
• /
• 2002

A parametric study has been conducted to investigate the effect of the geometry on the strength of an unidirectional and fabric hybrid laminated composite joint. Tests are conducted for the specimens with nine different edge-to-hole diameter or width-to-hole diameter ratios. For the finite element analysis, the characteristic length method is used, and the tests for determining the characteristic length are performed additionally. Nonlinear contact problem between the pin and laminate is modeled by the gap element in MSC/NASTRAN. Tsai-Wu failure criteria is applied to the stress on the characteristic curve. The finite element and experimental results shows good agreement in strength of composite joint. Results of the parametric study shows the effect of the geometry is remarkable in the specimens with width-to-hole diameter ratio less than 2.8 and edge-to-hole diameter ratio less than 1.4.

• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.23 no.9
• /
• pp.1192-1200
• /
• 1999

The present study investigates flow characteristics in a cavity with one rotating disk and co-rotating disks for application to HDD. The experiments are conducted for rotating Reynolds numbers of $5.5{\times}104$ to $1.10{\times}105$ and for gap ratios of 0.059 to 0.175 in a single rotating and 0.047 to 0.094 in co-rotating disk. Time-resolved velocity components and turbulence intensity on the rotating disks are obtained by using LDA measurements. Detailed Knowledge of the flow characteristics is essential to analyze flow vibration and heat transfer and to design head-arm assembly and hub height in HDD. The results indicate that the velocity field in HDD is changed largely by the rotating Reynolds numbers and hub height of the disk.

• Journal of the Korean Graphic Arts Communication Society
• /
• v.16 no.3
• /
• pp.29-41
• /
• 1998

The ultraviolet(UV)-curable materials wildly have been used as a ink and coating materials. A according to measure UV polymerization phase separation of acryl groups 2,3,4-functional monomer, a few experiments were performed gel fraction, dynamic viscosity of alkyd resin blend system. Dependence of photoiniator concentration and various monomer, alkyd resin content investigated structural changes of films cured by UV irradiation. Curing rate measured UV irradiation under $25^{\circ}C$, cell gap 7cm and film thickness 100${\mu}{\textrm}{m}$. In results, it was through that the viscoelastic properties of films cured with increasing the ratios of monomer/alkydresin contents are network polymer in properties such as viscoelasticity.

• 한국정보디스플레이학회:학술대회논문집
• /
• 2006.08a
• /
• pp.898-901
• /
• 2006

To fabricate mono layer green sheet (MLGS) of transparent dielectric for PDP front panel, dispersion of transparent dielectric slurry and various properties of green sheets were examined as a function of amount and kinds of organic additives. Sedimentation height and viscosity of slurry were measured to determine proper types and amount of dispersant in non-aqueous system transparent dielectric slurry. Many MLGS having various ratios of the transparent dielectric glass frit, binder and plasticizer were fabricated. Finally we got the transparent dielectric layer of high transparency and free from residual pore might be remained in the gap between the electrodes.

• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.31 no.6 s.261
• /
• pp.566-573
• /
• 2007

Flows around two oscillating cylinders in side-by-side arrangement at Re=185 are simulated using an immersed boundary method. The cylinders oscillate vertically in opposite directions in uniform cross-flow. We describe flow patterns, drag and lift forces by varying distance between two cylinders $(1.4{\leq}g{\leq}2.2,\;1.0{\leq}g{\leq}1.8)$ and oscillating frequency ratios $(f_e/f_o=0.8,\;f_e/f_o=1.0\;and\;f_e/f_o =1.2)$. Wake patterns, drag and lift coefficients are affected by both of frequency ratio and gap between two cylinders. Near wakes of each case are classified with the definition of previous studies.

• International Journal of Naval Architecture and Ocean Engineering
• /
• v.7 no.5
• /
• pp.795-804
• /
• 2015

Tip clearance loss is a limitation of the improvement of turbomachine performance. Previous studies show the Tip clearance loss is generated by the leakage flow through the tip clearance, and is roughly linearly proportional to the gap size. This study investigates the tip clearance effects on the performance of ducted propeller. The investigation was carried out by solving the Navier-Stokes equations with the commercial Computational Fluid Dynamic (CFD) code CFX14.5. These simulations were carried out to determine the underlying mechanisms of the tip clearance effects. The calculations were performed at three different chosen advance ratios. Simulation results showed that the tip loss slope was not linearly at high advance due to the reversed pressure at the leading edge. Three type of vortical structures were observed in the tip clearance at different clearance size.

• Structural Engineering and Mechanics
• /
• v.54 no.5
• /
• pp.877-890
• /
• 2015

This paper aims to fill the technical gap on the elastic buckling behavior of functionally graded material (FGM) grid systems under inplane loads on which few research has been done. Material properties of an FG beam are assumed to vary smoothly in the thickness direction according to power and exponential laws. Based on a hybrid-stress finite element formulation, buckling solutions for FGM grid systems consisting of various aspect ratios and material gradation are provided. The numerical results demonstrate that the aspect ratio and material gradation play an important role in the buckling behavior of FGM grid systems. We believe that the new results obtained from this study, will be very useful to designers and researchers in this field.

• Journal of the Korean Society of Manufacturing Process Engineers
• /
• v.10 no.6
• /
• pp.77-82
• /
• 2011

The piston-cylinder mechanism is widely adopted in the hydraulic machine components. In these cases, the hydrodynamic pressures are generated in the clearance gap between the piston and cylinder under lubrication action of the piston. Under the eccentric and tilted condition of the piston in the cylinder bore, the non-symmetric pressure distributions in the circumferential direction result in lateral forces. When the lateral forces act as increasing the eccentricity and tilting ratios, excessive wear can be result in cylinder and piston which are well known 'hydraulic locking' phenomena. In this paper, the hydrodynamic pressures generated in the clearance are measured using a stationary piston and moving cylinder apparatus. The experimental results showed that the hydrodynamic pressure distributions are highly affected by the speed and eccentricity of the cylinder and the oil viscosity.

• Journal of Magnetics
• /
• v.7 no.2
• /
• pp.55-58
• /
• 2002

MR transfer behaviors of the permanent magnet biased spin valve MR sensors with SyAF (synthetic antiferromagnet) layers were studied by micromagnetics modeling. For narrow track MR heads, various height to width ratios were considered together with strength of permanent magnets which stabilities the free layed As the MR sensor width is reduced to $0.12 \mu{m}$, sensor height less than 0.09 ${\mu}{\textrm}{m}$ is needed to show good linearity and the Mr.t of permanent magnets smaller than 0.2 memu/$cm^2$ is sufficient for the domain stabilization. The conditions for single domain behavior of the free layer were also investigated through optimizing the biasing strength of permanent magneto the shield gap and the aspect ratio of MR sensor.

• Proceedings of the KIEE Conference
• /
• 2004.11a
• /
• pp.237-239
• /
• 2004

송전용 피뢰장치의 공극 및 정격을 설계하는 기술을 검토하였다. 공극형 피뢰기를 설계하기 위해서는 먼저 공극의 길이를 결정하는 것이 우선되어야한다. 공극의 길이는 주변 아킹흔 및 피뢰기 소자의 제한전압 방전특성과의 절연협조를 통해 결정되며 속류차단성능 또한 적절한 공극설계로부터 확보된다. 송전용 피뢰장치의 정격전압은 TOV특성과 과전수명특성 등을 지배하는 접지계수와 여유도 등이 달라진다. 절연협조와 속류차단성능은 공극의 길이를 최적으로 설계하여야 가능하므로 세심한 주의가 요구된다. 계통전압 154W급 송전용 피뢰장치의 공극길이를 650m로 설계하는 경우 피뢰기 소자의 제한전압은 228kV로 설계가 가능하다.