• Transactions on Electrical and Electronic Materials
• /
• v.12 no.4
• /
• pp.131-134
• /
• 2011

Back-end-of-line using ultra low-k (ULK; k < 2.5) has been required to reduce resistive capacitance beyond 45 nmtechnologies, because micro-processing units need higher speed and density. There are two strategies to manufacture ULK inter-layer dielectric (ILD) materials using an air-gap (k = 1). The former ULK and calcinations of ILD degrade the mechanical strength and induce a high cost due to the complication of following process, such as chemical mechanical polishing and deposition of the barrier metal. In contrast, the air-gap based low-k ILD with a relatively higher density has been researched on the trench-type with activity, but it has limited application to high density devices due to its high air-gap into the next metal layer. The height of air-gap into the next metal layer was reduced by changing to the via-typed air-gap, up to about 50% compared to that of the trench-typed air-gap. The controllable ULK was easily fabricated using the via-typed air-gap. It is thought that the via-type air-gap made the better design margin like via-patterning in the area with the dense and narrow lines.

• Journal of Korean Society of Forest Science
• /
• v.96 no.2
• /
• pp.227-234
• /
• 2007

The forest canopy gap has been well known as a substantial process of forest cyclic regeneration and important role in stand structure, dynamics, and biodiversity of the forest ecosystem. Based on 3,600 $5m{\times}5m$ square grids in a 9ha permanent experimental plot, the study was conducted to evaluate the regeneration pattern of woody species by developmental stage {seedlings (<1 m of height), saplingI (>1 m of height, <2 cm of DBH), and saplingII (2 cm$<200m^2$), $201-400m^2$, $400-600m^2$, $601-800m^2$, and $>800m^2$) in the mixed broadleaved-Korean pine forest. The results indicated that the regenerating trees of Populus ussuriensis occurred only in the canopy gap area, considered to be a typical gap-dependent species. The regeneration of Ulmus japonica, Ulmus laciniata, and Maackia amurensis could be generally satisfied with the gap size of $201-600m^2$, Betula costata and Prunus padus with gap size of $401-800m^2$, Picea koraiensis with gap size of $201-800m^2$, Fraxinus mandshurica and Syringa reticulata var. mandshurica with smaller than $800m^2$, respectively. Acer ukurunduense and Acer tegmentosum were likely to have no problem with the gap size to make gap regeneration. Acer mono and Tilia amurensis looked more capable of regenerating in the closed canopy disregarding the upper crown condition. The regeneration of Pinus koraiensis and Abies nephrolepis had no trouble under the canopy condition in less than $800m^2$of gap size. The density of regenerating shrubs was rather high, especially under the closed canopy, considered to be associated with great amount of regeneration production in such shade tolerant species as Lonicera maackii, Corylus mandshurica, Euonymus pauciflorus, and Philadelphus schrenkii under the closed canopy. Pearson correlation coefficient was computed to compare the similarity among non-gap area and five gap size classes by developmental stages for trees and shrubs. The similarity coefficients among closed canopy and the gap size classes were mostly significantly correlated to each other with a few exceptions.

• The Korean Journal of Ecology
• /
• v.18 no.1
• /
• pp.189-201
• /
• 1995

In order to clarify regeneration processes and mechanisms of the disturbed Pinus densiflora forest, responses of Pinus densiflora to gap formed by disturbance were analysed by growth of saplings and mature and growth equations were obtained from branch growth of mature trees and height growth of saplings, and age distribution of saplings and young trees recruited within gap was analysed in relation to gap age. Height growth of saplings within gaps was accelerated after gap formation. Such abrupt increases of growth of saplings after the gap formation might be resulted in the difference of growth of saplings between gap and non-gap areas. In fact, height and diameter of saplings in the central part of gap were larger than those of saplings in marginal parts of gap and non-gap area. However, density of saplings was not different in both parts. In addition, growth of annual rings of mature trees bordering on gap also increased after gap formation. Branch growth of mature trees bodering on gap was 6.3 - 6.5 cm /year and the mean radius of gaps created by death of only one canopy tree was about 3 m. Therefore, for those gaps to be closed by branch growth it will take 46 years. Growth of saplings within gap showed exponential equation. Fifty years will be required for the saplings to enter the forest canopy by the exponential growth equation. Therefore, gap created by only one tree might be closed by branch growth of surrounding canopy trees in advance of being done by height growth of saplings. But gaps created by death of trees more than 2 will be closed by the growth of saplings. Among the regenerating saplings and young trees within gaps, individuals established in advance of gap formation were more than those established after the gap formation. From these results, it was assumed that the disturbed Pinus densiflora forests in these sites were regenerated by height growth of saplings recruited in advance of gap formation.

• The Transactions of the Korean Institute of Electrical Engineers B
• /
• v.52 no.11
• /
• pp.535-540
• /
• 2003

Since axial flux motor has an advantage over more conventional radial flux type motor such as high power density, it can be used as a power train for hybrid electric vehicle and electric vehicle. Also operating range can be extended and efficiency can be improved by changing air gap. Optimal operating air gap is estimated based on the measured efficiency at different air gap. Motor model is developed based on estimated optimal air gap and efficiency. Motor/controller performance is analyzed through simulation. Possible application area of axial flux motor was explored through simulation.

• Journal of Korea Multimedia Society
• /
• v.15 no.1
• /
• pp.32-39
• /
• 2012

In this paper, the implementation of location based services (LBS) using S-DMB (satellite-digital multimedia broadcasting) system was proposed. In S-DMB System, the frequency of transmitted signal is about 2 GHz which has a characteristics of strong straightness but weak diffraction so that there are many shade areas such as indoors and underground spaces. Therefore the signal transmitted from the satellite should be retransmitted by the earth repeaters called as gap filler. Because each gap filler has its own identification value, the gap filler ID introduces the area in which the gap filler was installed. Generally, the 51st data symbols of S-DMB pilot signal transmitted from the satellite are padded by dummy value and gap filler ID is embedded in this pilot symbol by the gap filler when S-DMB signals are retransmitted by gap fillers. So using gap filler ID of S-DMB system, LBS such as region registration, distance and time to destination, alarm of local area information could be implemented. In the experiment to prove the performance of the proposed LBS system using the gap filler ID of the S-DMB system, the firmware of S-DMB chip composing of RF and baseband parts was lightly modified so that application processor was able to manipulate the gap filler ID and the its related regional information.

• Composites Research
• /
• v.37 no.1
• /
• pp.7-14
• /
• 2024

Due to the structural characteristic of a double roller, the double roller can have various deformation behaviors depending on a gap block design, even if dimensions and loading conditions for the double roller are the same. Based on this feature, we propose a strategy for designing the gap block of the carbon-fiber reinforced plastic (CFRP) double roller to minimize defects (e.g., sagging and wrinkling), which can be raised during the product conveying process, with the pursue of the lightweight design. In the suggested strategy, analysis cases are first selected by considering main design parameters and engineering tolerances of the gap block, and then deformation behaviors of these selected cases are extracted using the finite element method (FEM). Here, to obtain the optimal gap block parameters that satisfy the purpose of this study, deformation deviations in the contact area are calculated and compared using the extracted deformation behaviors. Note that the contact area in this work is located between the product and the roller. As a result, through the design method of the gap block proposed in this work, it is possible to construct the CFRP double roller that can significantly decrease the defects without changing the overall sizes of the roller. A detailed method is suggested herein, and the results are evaluated in a numerical way.

• Journal of Korea Foundry Society
• /
• v.29 no.6
• /
• pp.270-276
• /
• 2009

After casting button-type small ingots of ternary Fe-Mn-S alloys which had three different Mn/S ratios (1, 5 and 70) in a vacuum arc furnace, the effect of the ratio on the sulfide formation was investigated. In case of the Mn/S ratio of 1, if alloy composition was located in an iron-rich corner on a Fe-Mn-S ternary phase diagram, only duplex MnS-FeS sulfide films were observed in the grain boundary. If the alloy composition was located in the miscibility gap area of the phase diagram, primary globular dendritic sulfides and dendritic sulfide slags were generated within the grain and tubular monotectic sulfides were also detected in the grain boundary. When the Mn/S ratio was 5, if the alloy composition was in the iron-rich corner, only bead-like sulfides were generated. On the other hand, if the composition was in the miscibility gap area, globular dendritic sulfides and dendritic sulfide slags were generated in the form of primary sulfide inclusions and rod-like eutectic sulfides were observed in the grain boundary. Especially, if the contents of Mn and S increased more in the miscibility gap area of the phase diagram, primary globular sulfides containing iron intrusions were observed. In case of Mn/S ratio of 70, if the contents of Mn and S was decreased in the Fe corner of the phase diagram, only bead-like sulfides were observed in the grain boundary. Despite the composition was outside the miscibility gap area of the phase diagram, if the contents of Mn and S increased, clusters of fine sulfide particles as well as fine spherical primary monophase sulfides were observed in the grain boundary.

• Proceedings of the KSR Conference
• /
• 2011.05a
• /
• pp.1509-1518
• /
• 2011

Shield TBM tunneling method has been getting the spotlight for urban tunneling. It can be minimized the civil complaint during construction and possible safe tunneling. But the settlement has occurred inevitably due to characteristics of shield TBM equipment. For this reason, the civil complaint can occur in urban areas when tunnel with shallow depth passes through neighboring building or residential area. In this study, the occurrence factors of settlement according to shield TBM tunneling and the tendency of ground settlement by strata condition had analyzed. It is suggested that the practical settlement estimation method and minimizing method of ground settlement under simultaneous backfill grouting condition through measurement results and back analysis data using gap parameter.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.29 no.2 s.233
• /
• pp.220-227
• /
• 2005

In this study, stress-displacement analytic solutions are obtained by a shear lag modeling method constructed for the spliced joint area with a splicing gap in the fiber metal laminate (FML). This gap can be empty or be filled with an adhesive material of elastic modulus $E_a$. Two splicing types are considered for spliced shear models, one for spliced in the center metal layer, the other for spliced in the outer metal layer. It is shown that from the viewpoint of the load transfer efficiency and the avoidability of disbond generation due to the shear and axial stresses at the interface between metal layer and composite layer of the gap-front in the spliced area, the center spliced type (k=2) is much preferable to the outer spliced type (k=1).

• Journal of the Korean Crystal Growth and Crystal Technology
• /
• v.16 no.5
• /
• pp.198-202
• /
• 2006

We could achieve the bridge-type formation of the iridium-catalyzed carbon nanofibers across the gap on the MgO substrate using microwave plasma enhanced chemical vapor deposition method. On the plane surface area of the MgO substrate, the iridium-catalyzed carbon nanofibers were grown as a lateral direction to the substrate. The bridge-type formation and/or the lateral growth of the iridium-catalyzed carbon nanofibers were interconnected with each other. Finally, they could form an entangled network having the bridge-type formation of the carbon nanofibers across the gap on the substrate and the laterally-grown carbon nanofibers on the plane surface area of the substrate. The entangled network showed the semiconductor electrical characteristics.