• 전기학회논문지
• /
• 제60권11호
• /
• pp.2049-2055
• /
• 2011

In this paper a new current control method is proposed for the discontinuous conduction mode of boost converter. The proposed method using a current gain feedforward compensation adjusts a measured inductor current value and then, calculated an average current precisely in the discontinuous conduction mode as well as continuous conduction mode. By applying the proposed method, the current measurement error is significantly reduced to 2% regardless of the operating points. The proposed method is analyzed and its performance is investigated in simulation. To verify the feasibility of the proposed scheme, a 10kW 3-phase interleaved boost converter was built and experimental results are matched to the simulation results.

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 2012년도 춘계학술대회 논문집
• /
• pp.423-424
• /
• 2012

• 전기학회논문지P
• /
• 제59권3호
• /
• pp.253-257
• /
• 2010

The frequency is an important operation parameter for the control, protection, and stability of a power system. The frequency as a key index of power quality can be indicative of system abnormal conditions and disturbances. Due to the sudden change in generation and loads or faults in power system, the frequency is supposed to deviate from its nominal value. It is essential that the frequency must be maintained very close to its nominal frequency. An accurate monitoring of the power frequency is essential to optimal operation and prevention for wide area blackout. As most conventional frequency estimation schemes are based on DFT filter, it has been pointed out that the gain error could cause defects when the frequency is deviated from nominal value. This paper presents an advanced frequency estimation technique using gain compensation to improve the performance of DFT filter based techniques. To evaluate performance of the proposed algorithm, the 765kV T/L system in Korea is simulated by EMTP-RV software. The proposed technique can reduce the gain error caused when the power system frequency deviates from nominal value.

• 한국컴퓨터산업학회논문지
• /
• 제9권2호
• /
• pp.77-82
• /
• 2008

The diversity reception and the equal gain combining technique are applied to the compensation of the distortion of channel, which occurs in transmission of data at rapid speed. DSSS BPSK system which has the receiving structure with the compensation algorithm is formed on the diversity branch, and the characteristics of the system are evaluated at the view point of the average bit error rate due to the SNR. In addition, the multi-tap update algorithm which is superior for the data compensation is suggested. Moreover, using the American Joint Technical Committee PCS RF channel characterization and system deployment model standard, the suggested multi-tap update algorithm is compared and analyzed with the view-point of the average bit error rate and convergence speed for evaluating the realistic efficiency of the system.

• 한국통신학회논문지
• /
• 제21권8호
• /
• pp.2055-2062
• /
• 1996

This paper presents a method of compensating for the gain and phase imbalance of quadrature modulator and demodulator. The gain and phase imbalance are compensated using the received power after the compensation pattern was transmitted at tranceiver. The proposed method is less vulnerable to changes in the transmission channel than the conventional method because compensation is made possible within the tranceiver system, and even the change in phase mblance in accordance with frequency can be compensated utilizing the adaptive algorithm. According to numerical results, a normalized eye opening and a bit error rate are improved by 1.8dB and 3.8dB, respectively.

• 한국해양공학회지
• /
• 제13권3B호
• /
• pp.91-98
• /
• 1999

In order to reject the steady-state tracking error, it is common to introduce integral compensators in servosystems for constant reference signals. However, if the mathematical model of the plant is exact and no disturbance input exists, the integral compensation is not necessary. From this point of view, a two-degree-of-freedom(2DOF) servosystem has been proposed, in which the integral compensation is effective only when there is a modeling error or a disturbance input. The present paper considers a synthesis problems of this 32DOF servosystem with direct transfer term in the system representation. And, a method how we may obtain a gain such that desirable transient response is achieved, is proposed in the presence of the modelling error and disturbance input.

• Journal of Mechanical Science and Technology
• /
• 제14권11호
• /
• pp.1198-1205
• /
• 2000

A two-degrees-of-freedom servosystem for step-type reference signals has been preposed, in which the integral compensation is effective only when there is a modeling error or a disturbance input. this paper considers robust stability of the servosystem incorporating an observer against both structured and unstructured uncertainties of the plant. A condition is obtained as a linear matrix inequality, under which the servosystem is robustly stable independently of the gain of the integral compensator. This result implies that we can tune the gain to achieve a desirable transient response of the servpsystem preserving robust stability. An example is presented to demonstrate that under the robust stability condition, the transient response can be improved by increasing the gain of the integral compensator.

• ETRI Journal
• /
• 제31권5호
• /
• pp.601-603
• /
• 2009

This letter presents a high performance 2.4 GHz two-stage power amplifier (PA) operating in the temperature range from $-30^{\circ}C$ to $+85^{\circ}C$ for IEEE 802.11g, wireless local area network application. It is implemented in InGaP/GaAs hetero-junction bipolar transistor technology and has a bias circuit employing a temperature compensation technique for error vector magnitude (EVM) performance. The technique uses a resistor made with a base layer of HBT. The design improves EVM performance in cold temperatures by increasing current. The implemented PA has a dynamic EVM of less than 4%, a gain of over 26 dB, and a current less than 130 mA below the output power of 19 dBm across the temperature range from $-30^{\circ}C$ to $+85^{\circ}C$.

• 제어로봇시스템학회:학술대회논문집
• /
• 제어로봇시스템학회 2000년도 제15차 학술회의논문집
• /
• pp.431-431
• /
• 2000

The modeling of 5-bar linkage robot manipulator dynamics by means of a mathematical and neural architecture is presented. Such a model is applicable to the design of a feedforward controller or adjustment of controller parameters. The inverse model consists of two parts: a mathematical part and a compensation part. In the mathematical part, the subsystems of a 5-bar linkage robot manipulator are constructed by applying Kawato's Feedback-Error-Learning method, and trained by given training data. In the compensation part, MLP backpropagation algorithm is used to compensate the unmodeled dynamics. The forward model is realized from the inverse model using the inverse of inertia matrix and the compensation torque is decoupled in the input torque of the forward model. This scheme can use tile mathematical knowledge of the robot manipulator and analogize the robot characteristics. It is shown that the model is reasonable to be used for design and initial gain tuning of a controller.

• 한국안전학회지
• /
• 제9권4호
• /
• pp.42-48
• /
• 1994

A rotor flux error-based approach for correcting the rotor time constant estimation used in the slip frequency calculator of indirect field oriented controller is presented in this paper. The controller was derived from the d-q induction machine model. Slip frequency gain is dependent on the machine parameter errors. And parameter errors result in rotor flux error. Thus, estimated rotor flux is compared to commanded rotor flux. The error between them is used for the estimation of rotor time constant. Simulation results which demonstrate the performance of this approach are presented.