• Title/Summary/Keyword: fume generation

Search Result 35, Processing Time 0.038 seconds

Analysis of the Fume Generation Rates in the Flux Cored Arc welding

  • Chae, H.B.;Kim, J.H.;Yang, S.C.
    • International Journal of Korean Welding Society
    • /
    • v.1 no.1
    • /
    • pp.71-77
    • /
    • 2001
  • The characteristics of the fume generation in a flux cored arc welding were investigated using the fume collection chamber developed. The Korean Standard concerning the method for the evaluation of the fume generation rate(FGR) was updated by the evaluation method obtained through this study. It was found that the effect of humidity in the test environment should be considered and the automatic welding method had to be employed for the purpose of the exact evaluation of the fume generation rate. The results showed that the fume generation rate was influenced by the welding parameters. The important factors were the welding current arc voltage, travel speed, and contact tip to work distance(CTWD) that affected the heat input as well as the torch angle and the shielding gas flow rate that influenced the shielding effect. The fume generation rate increased as the heat input increased and the shielding effect decreased. It was also observed that the effect of the welding current is much grater than the other welding parameters.

  • PDF

Welding Fume and Others from Welding Processes

  • Yoon, Chung-Sik
    • Journal of Environmental Health Sciences
    • /
    • v.30 no.4
    • /
    • pp.320-328
    • /
    • 2004
  • A number of health hazards are generated in welding processes. In this paper, the characteristics of fumes and some other hazardous agents in welding are reviewed. Fumes in welding are generated by complex mechanism like physical ejection of particles, oxidation-enhanced vaporization, vaporization-condensation-oxidation, and spatter contribution. Fume generation rates could be described as a power function in a given process. Most of fume constituents was originated from consumables rather than base metal. The mass distribution for the welding fumes is unimodal and very small to penetrate respiratory system. So, almost fractions of fumes are classified into the respirable particulate mass. Total chromium contents in FCAW were similar to those from SMAW whereas hexavalent chromium concentrations in fume were similar to those produced from MIG welding fume. Hexavalent chromium was mostly soluble which was similar to the characteristic solubility of fume hexavalent chromium from SMAW.

A Study on the Effect of Welding Conditions on Fume Generation Rate in $CO_2$ Flux Cored Arc Welding ($CO_2$ FCAW에서 용접조건이 Fume발생량에 미치는 영향에 관한 연구)

  • 채현병;김정한;김희남
    • Journal of the Korean Society of Safety
    • /
    • v.13 no.4
    • /
    • pp.87-95
    • /
    • 1998
  • The use of flux cored arc welding(FCAW) process has grown dramatically since it has been developed because of the remarkable operating characteristics and the resulting weld properties. The feature that distinguishes the FCAW process from other arc welding processes is the enclosure of fluxing ingredients within a continuously fed tubular electrode. The benefits of FCAW process are the increased productivity due to continuous wire feeding, the metallurgical effects derived from the reactions with flux, and the shapes of weld bead formed by slag. However, FCAW process causes the problem in working environment because it generates much more fume than other welding processes. Recently, the welding fume became a hot issue in the field after some welders were diagnosed as manganese toxcosis and siderosis. This study was started to investigate the characteristics of welding fume and utilize the results from the investigation to protect the welders from welding fume. As a first step, the effect of welding conditions on the fume generation rate(FGR) were investigated during FCAW process with $CO_2$ shielding. The considered welding conditions were welding current, arc voltage, travel speed, contact tube to work distance, and torch angle. The results showed that FGR was affected by all of these factors.

  • PDF

A Study on the Evaluation of Welding Fume Generated during Arc Welding (Arc 용접시 Fume 발생량 평가에 관한 연구)

  • 채현병;김정한;김희남
    • Journal of the Korean Society of Safety
    • /
    • v.13 no.2
    • /
    • pp.65-75
    • /
    • 1998
  • The cases of welders illness by welding fume generated during arc welding are recently reported, which makes the legal regulation in the welding work place. Also, this situation makes the employers and welders be concerned about the welding fume seriously. At this point of time it is necessary that a standard testing method is developed as a fundamental tool for the evaluation of Fume Generation Rate(FGR) required for making progress in the development of low fume electrodes and welding process technology and also constructing the ventilation system in welding area. However, the current standard(KS D 0062) is only applicable to the manual covered electrode arc welding. In this study the evaluation procedure for the FGR is established by developing the fume collection chamber which can be applicable to semiautomatic and automatic arc welding as well as manual arc welding. This evaluation system and procedure can be used as a tool not only to develop the low fume welding electrode and welding process technology but also to construct the equipment controlling the welding workshop atmosphere.

  • PDF

Downward and Upward Air Flow Effects on Fume Particle Dispersion in Laser Line Cutting of Optical Plastic Films

  • Kim, Kyoungjin
    • Journal of the Semiconductor & Display Technology
    • /
    • v.19 no.2
    • /
    • pp.37-44
    • /
    • 2020
  • In improving laser cutting of optical plastic films for mass production of optoelectronics display units, it is important to understand particle contamination over optical film surface due to fume particle generation and dispersion. This numerical study investigates the effects of downward and upward air flow motions on fume particle dispersion around laser cut line. The simulations employ random particle sampling of up to one million fume particles by probabilistic distributions of particle size, ejection velocity and angle, and fume particle dispersion and surface landing are predicted using Basset-Boussinesq-Oseen model of low Reynolds number flows. The numerical results show that downward air flow scatters fume particles of a certain size range farther away from laser cut line and aggravate surface contamination. However, upward air flow pushes fume particles of this size range back toward laser cut line or sucks them up with rising air motion, thus significantly alleviating surface contamination.

Dispersion Characteristics of Nonspherical Fume Micro-Particles in Laser Line Machining in Terms of Particle Sphericity (입자 구형도에 따른 레이저 선가공의 비구형 흄 마이크로 입자 산포 특성 연구)

  • Kim, Kyoungjin;Park, Joong-Youn
    • Journal of the Semiconductor & Display Technology
    • /
    • v.21 no.2
    • /
    • pp.1-6
    • /
    • 2022
  • This computational investigation of micro-sized particle dispersion concerns the fume particle contamination over target surface in high-precision laser line machining process of semiconductor and display device materials. Employing the random sampling based on probabilistic fume particle generation distributions, the effects of sphericity for nonspherical fume particles are analyzed for the fume particle dispersion and contamination near the laser machining line. The drag coefficient correlation for nonspherical particles in a low Reynolds number regime is selected and utilized for particle trajectory simulations after drag model validation. When compared to the corresponding results by the assumption of spherical fume particles, the sphericity of nonspherical fume particles show much less dispersion and contamination characteristics and it also significantly affects the particle removal rate in a suction air flow patterns.