• Structural Engineering and Mechanics
• /
• 제59권2호
• /
• pp.327-341
• /
• 2016

This study addresses the effect of pre-stressed cables on a pre-stressed mega-braced steel frame through employing static analysis and pushover analysis. The performances of a pre-stressed mega-braced steel frame and a pure steel frame without mega-braces are compared in terms of base shear, ductility, and failure mode. The influence of the cable parameters is also analyzed. Numerical results show that cable braces can effectively improve the lateral stiffness of a pure frame. However, it reduces structural ductility and degenerates structural pre-failure lateral stiffness greatly. Furthermore, it is found that 20% fluctuation in the cable pretension has little effect on structural ultimate bearing capacity and lateral stiffness. As comparison, 20% fluctuation in the cable diameter has much greater impact.

• 한국자동차공학회논문집
• /
• 제11권4호
• /
• pp.226-231
• /
• 2003

There have been many attempts to make kart chassis domestically to lower the price of complete kart. However nobody made a successful chassis due to the lack of understanding the characteristics of kart chassis frame. In this work, a baseline chassis frame under the bending and torsional load is studied. Design target is that the baseline chassis frame is quite adequate not only for the beginners but also for the beginning racers. Results from the analysis are used as a guide to design or modify the baseline chassis with the goal of proper torsional stiffness. Minimum increase in weight is being forced. As a result, the baseline chassis frame was designed, made, and tested. Based on the design results, complete karts are being manufactured by the small 1 size domestic company and these karts are being sold and run in the market.

• 한국철도학회논문집
• /
• 제2권2호
• /
• pp.31-38
• /
• 1999

Two representative types of the AGT (Automated Guideway Transit) system, which are bogie and steering types, are available for the side-guided system. Each system primarily consists of the bogie frame, suspensions, wheelsets and axles, braking system and transmission system. Among these components, the bogie frame is one of the most significant components subjected to the whole vehicle and passenger loads. This paper describes structural analyses and associated fatigue analyses for each bogie frame depending on the various loading conditions on a basis of the railway vehicle code UIC 515-4. Subsequently, comparisons are made between those two types to estimate which type is more reliable in terms of strength and fatigue. It is observed that the bogie type is a little advantageous over the steering one from the strength analysis. However, the two types are found to be in a reliable range of fatigue even though a realistic fatigue load case is further carried out. In addition, an optimal size of thickness is suggested for designs of the bogie frame.

• Structural Engineering and Mechanics
• /
• 제44권1호
• /
• pp.85-107
• /
• 2012

The building frame and its foundation along with the soil on which it rests, together constitute a complete structural system. In the conventional analysis, a structure is analysed as an independent frame assuming unyielding supports and the interactive response of soil-foundation is disregarded. This kind of analysis does not provide realistic behaviour and sometimes may cause failure of the structure. Also, the conventional analysis considers infill wall as non-structural elements and ignores its interaction with the bounding frame. In fact, the infill wall provides lateral stiffness and thus plays vital role in resisting the seismic forces. Thus, it is essential to consider its effect especially in case of high rise buildings. In the present research work the building frame, infill wall, isolated column footings (open foundation) and soil mass are considered to act as a single integral compatible structural unit to predict the nonlinear interaction behaviour of the composite system under seismic forces. The coupled isoparametric finite-infinite elements have been used for modelling of the interaction system. The material of the frame, infill and column footings has been assumed to follow perfectly linear elastic relationship whereas the well known hyperbolic soil model is used to account for the nonlinearity of the soil mass.

• Structural Engineering and Mechanics
• /
• 제46권5호
• /
• pp.645-672
• /
• 2013

The differential settlements and rotations among footings cannot be avoided when the frame-footing-soil system is subjected to seismic/dynamic loading. Also, there may be a situation where column(s) of a building are located near adjoining property line causes eccentric loading on foundation system. The strap beams may be provided to control the rotation of the footings within permissible limits caused due to such eccentric loading. In the present work, the seismic interaction analysis of a three-bay three-storey, space frame-footing-strap beam-soil system is carried out to investigate the interaction behavior using finite element software (ANSYS). The RCC structure and their foundation are assumed to behave in linear manner while the supporting soil mass is treated as nonlinear elastic material. The seismic interaction analyses of space frame-isolated footing-soil and space frame-strap footing-soil systems are carried out to evaluate the forces in the columns. The results indicate that the bending moments of very high magnitude are induced at column bases resting on eccentric footing of frame-isolated footing-soil interaction system. However, use of strap beams controls these moments quite effectively. The soil-structure interaction effect causes significant redistribution of column forces compared to non-interaction analysis. The axial forces in the columns are distributed more uniformly when the interaction effects are considered in the analysis.

• Computers and Concrete
• /
• 제21권4호
• /
• pp.451-461
• /
• 2018

Present study is mainly concerned about the idea of innovative utilization of bamboo in modern construction. Owing to its compatible mechanical properties, a beneficial effect of its use in reinforced concrete (RC) frame infills has been observed. In this investigation, finite element analyses have been performed to examine the failure pattern and stress distribution pattern through the infills of a moment resisting RC frame. To validate the pragmatic use of bamboo reinforced components as infills, earthquake loading corresponding to Nepal earthquake had been considered. The analysis have revealed that introduction of bamboo in RC frames imparts more flexibility to the structure and hence may causes a ductile failure during high magnitude earthquakes like in Nepal. A more uniform stress distribution throughout the bamboo reinforced wall panels validates the practical feasibility of using bamboo reinforced concrete wall panels as a replacement of conventional brick masonry wall panels. A more detailed analysis of the results have shown the fact that stress concentration was more on the frame components in case of frame with brick masonry, contrary to the frame with bamboo reinforced concrete wall panels, in which, major stress dispersion was through wall panels leaving frame components subjected to smaller stresses. Thus an effective contribution of bamboo in dissipation of stresses generated during devastating seismic activity have been shown by these results which can be used to concrete the feasibility of using bamboo in modern construction.

• 한국해양공학회지
• /
• 제27권6호
• /
• pp.65-72
• /
• 2013

This paper describes a finite element analysis (FEA) of the body frame of a subsea robot, Crabster200 (CR200). CR200 has six legs for mobility instead of screw type propellers, which distinguishes it from previous underwater robots such as remotely operated vehicles (ROVs) and autonomous underwater vehicles (AUVs). Another distinguishing characteristic is the body frame, which is made of carbon fiber reinforced plastic (CFRP). This body frame is designed as a rib cage structure in order to disperse the applied external loads and reduce the weight. The frame should be strong enough to support many devices for exploration and operation underwater. For a reasonable FEA, we carried out specimen tests. Using the obtained material properties, we performed a modal analysis and FEA for CR200 with a ready posture. Finally, this paper presents the FEA results for the CFRP body frame and the compares the characteristics of CFRP with conventional material, aluminum.

• 한국공간구조학회논문집
• /
• 제13권2호
• /
• pp.83-91
• /
• 2013

The core aim of this dissertation is to empirically scrutinize a strength characteristic of beam-column frame subjected to the cyclic lateral load, a beam-column frame of un-reinforced masonry wall, and a shear wall frame. First and foremost, I embark upon making three prototypes vis-$\grave{a}$-vis this research. By conducting this process, I touch on an analysis of cyclic behavior and a damage characteristic of the beam-column frame, the beam-column frame of un-reinforced masonry wall, and the shear wall frame. What is more, through the previous procedure, the next part delves into the exact stress transfer path and the destructive mechanism to examine how much and how strong the beam-column frame of un-reinforced Masonry Wall does have a resistance capacity against earthquake in all the architecture constructed by the above-mentioned frame, as well as school buildings. In addition to the three prototypes, two more experimental models, a beam-column frame and shear wall frame, are used to compare with the beam-column frame of un-reinforced masonry wall. Lastly, the dissertation will suggest some solutions to improve the resistance capacity against earthquake regarding all constructions built with non bearing wall following having examining precisely all the analysis with regard to not only behavior properties and the damage mechanism of the beam-column frame and the beam-column frame of un-reinforced Masonry Wall but also the resistance capacity against earthquake of non bearing wall and school buildings.

• 한국자동차공학회논문집
• /
• 제19권5호
• /
• pp.113-117
• /
• 2011

The frame for automotive assembly can be deformed and remained on the residual stress due to high temperature thermal attacks when in welding. The frame deformation can be made to problems when in assembly with body and the residual stress can affect the negative effect on durability performance of the automobile. In order to analyze the frame deformation, the simplified test frame which had the similar shape (form) of the real automotive frame was fabricated. The contactless optical 3D scanner was used for the shape difference measurement of the frame between before and after the welding. The FE-model of the test frame was composed and the heat transfer and thermal stress simulation were performed. The simulated results were compared with the measured results for the reference of the frame design. The deformation shape of the frame by simulation was in good agreement with that by the experimental measurement.

• 한국융합학회논문지
• /
• 제9권11호
• /
• pp.271-276
• /
• 2018

자전거를 타는 운전자가 자전거를 탑승하게 되면 그 프레임에 실리게 되는 위치에 따라서 운전자의 하중이 다르게 나타난다. 자전거 프레임의 접합 부분에서 가장 많은 하중이 작용하게 되며, 프레임의 중간 부분에서 다른 부분 보다 하중이 적게 작용하게 된다. 그래서 자전거 하중이 많이 작용하지 않는 부분을 두께를 얇게 제작함으로서 프레임의 무게를 줄이고, 하중이 크게 작용하는 부분에는 두껍게 제작하여 하중을 잘 버틸수 있게 한다. CATIA 프로그램을 사용하여 일반 프레임, 더블 버티드, 트리플 버티드의 형상으로 모델링하였고, 구조해석 및 피로해석을 진행하여 탑승자의 하중에 의해 각각의 모델의 내구성을 검토하였다. ANSYS 해석 프로그램을 사용하여 확인하여 본 연구 결과로는 일반 프레임의 변형이 가장 많이 일어났고, 트리플 버티드의 변형이 가장 적었다. 이러한 시뮬레이션 해석 데이터를 사용하여 실제 자전거 프레임을 설계 및 제작 시에 가장 효율적인 방법으로 설계할 것으로 사료된다.