• 한국주조공학회지
• /
• 제41권1호
• /
• pp.16-25
• /
• 2021

환경오염방지와 에너지 소비 절감에 대한 기술 개발의 요구는 이미 사회 전체의 문제가 되고 있고, 주물산업에서의 환경과 에너지 관련 기술 개발 또한 최근 중요한 문제로 부상하고 있다. 본 논문에서는 주조공정에서 발생하는 분진의 친환경적인 집진처리를 위한 분진 흡입 시스템을 개발하고 기존의 건옥식 고출력 설비의 집진 효율과 비교 및 검토하였다. 넓은 범위를 집진하는 건옥식 방식은 에너지 및 집진 효율이 떨어지고, 건물 높이에 따라 효과를 보지 못 할 수도 있다는 단점이 있다. 또한 주물공장에서 발생하는 분진은 용해 후 출탕, 레이들 이송, 주입 공정까지 미세먼지의 발생원 위치가 연속적으로 바뀌기 때문에 효과적인 집진을 위한 국부적 범위의 이동식 집진장치의 개발이 요구된다. 이에, 본 논문에서는 이동하는 분진원에 효과적으로 대응할 수 있도록 크레인, 호이스트, 모노레일 등의 레이들 이송 장비에 집진 설비를 설치하고, 집진 특성을 평가하였다. 본 논문에서 개발한 이동형 집진 장치는 주물 생산 현장의 에너지 절감과 환경보호 측면에서 의의가 있으며, 타 산업 현장의 적용도 가능하다고 판단할 수 있다.

• 한국주조공학회지
• /
• 제10권4호
• /
• pp.284-288
• /
• 1990

• 한국산업보건학회지
• /
• 제7권2호
• /
• pp.196-208
• /
• 1997

This study was performed to estimate quartz contents in the both bulk and airborne dust samples and to determine particle size distribution of airborne dust from the selected foundry operations. Total dust samples were collected by a 37mm cassette and respirable by a 10 mm nylon cyclone. Particle size distributions were determined by a Marple's 8-stage cascade impactor at the melting, molding, shakeout and finishing operations. The presence of elements in the dust samples were confirmed by the scanning electron microscopy equipped with the energy dispersive x-ray spectrometry. The quartz contents were estimated using the intensity of the absorption peak of quartz at 799 cm-l by the Fourie Transformed Infrared Spectroscopy (FTIR). The results were as follows: 1. The analysis of data from cascade Impactor showed bimodal distributions of particle size at the melting, molding and shakeout operations. Mass median aerodynamic diameters for the distributions determined by histogram were $0.48-1.65{\mu}m$ for small and $13.43-19.58{\mu}m$ for large modes. In the dust samples collected at the finishing operations, however, only a large mode of $18.89{\mu}m$ was found. 2. The percentages of total to respirable dust concentration calculated from the impactor data ranged from 42 % to 66 %. The average concentrations of respirable dust by cyclone were $0.85-1.28mg/m^3$ collected from the workers, and were $0.23-0.56mg/m^3$ from the areas surveyed. Dust concentrations of personal samples were statistically significantly higher than those of area samples. The highest dust concentration was obtained from the personal samples of the finishing operation. 3. The mean percentages of silicon and oxygen estimated by SEM-EDXA in the bulk samples ranged from 35.83 % to 36.02 % and from 39.93 %-41.64 %, respectively. 4. The average quartz contents estimated by FTIR in the respirable dust from personal samples ranged from 4.32 % to 5.36 % and 4.54 % to 4.70 % in the bulk samples. No statistical difference of quartz content was found between foundry operations. In this study, quartz content was quantified by FTIR. Although no statistically significant difference in quartz content between airborne and bulk, samples and between different foundry operations was found, it is recommended that quartz content in the individual sample of respirable dust be analyzed and the results be used either to select an applicable quartz limits or to calculate the exposure limit. Further studies, however, are needed to compare the results by FTIR and XRD since it is reported that the quartz content determined by FTIR is different from that by XRD.

• 한국환경보건학회지
• /
• 제28권3호
• /
• pp.64-71
• /
• 2002

Hair provides important information about the body's mineral status. Therefore, we have studied the trace elemental distribution in human hair under different inhalation and ingestion environment using neutron activation analysis (NAA). NAA is a powerful analytical method which can be used successfully to determine trace elements in environmental and biological materials. Total diet and six different herbal medicine were analysed to study ingestion environment. Airborne dust in foundry was analysed and compared with outdoor dust to study inhalation environment. Human hairs of common person, herbal medicine taker and foundry worker were analysed to estimate the trace elemental distribution of people under different inhalation and ingestion environment. Analytical results show that herbal medicines contain higher micronutrients such as Ca, Mg, Mn and Cu that total diet and airborne dust in foundry has high Cr. The concentration of Ca, Mg and Mn in hair of herbal medicine taker is two times higher than in hair of common person and Cr con-centration in hair of foundry worker is about three times higher than in hair of common person. These results show that NAA can be used importantly to monitor human health through biological and environmental samples.

• 한국산업보건학회지
• /
• 제8권1호
• /
• pp.50-66
• /
• 1998

This study was conducted to estimate crystalline silica contents in airborne respirable dust from various manufacturing industries and to compare analytical performance of two methods of quantifying crystalline silica, X-ray diffraction(XRD) and Fourie transform infrared spectroscopy (FTIR). For this study, various manufacturing industries with a history of having pneumoconiosis cases and also known to generate dusts containing crystalline silica were investigated. These industries include: foundry, brick, potteries, concrete, and abrasive material, etc. Both personal and area respirable dust samples were collected using 10 mm, Dorr-Oliver nylon cyclone equipped with 37mm, $5{\mu}m$ pore size, polyvinylchloride (PVC) filters as collection media. In addition, total dust samples were collected side-by-side to the respirable samples. All samples were weighed before and after sampling and were pretreated according to the NIOSH sampling and analytical methods 0500, 7500, and 7602 for dust collection and quartz analysis. In addition, bulk samples were collected and analyzed by X-ray fluorescence (XRF) for minerals. In this article, only the results obtained from foundry are reported. The results from various other industries will be published in future articles. The respirable dust concentrations from personal samples by cyclone were $0.46-1.06mg/m^3$ and those from area samples were $0.34-0.73mg/m^3$. Dust concentrations of personal samples were significantly higher than those of area samples. The highest dust concentration was obtained from the personal samples of the finishing operation. Total dust concentration ranged $1.24-3.40mg/m^3$. The mean quartz contents estimated by FTIR and XRD in the personal respirable dust samples were 5.12% and 4.41%, respectively, without significant difference between them. For quartz analyses, the two techniques were highly correlated with $r^2$ ranged 0.803-0.920. But the results by FTIR were mostly higher than those by XRD. In addition, cristobalite was not detected by FTIR. Significant correlations between contents of crystalline silica and such minerals as $Al_2O_3$, CaO, $TiO_2$, and $K_2O$ suggest possible interferences from these minerals.

• 한국주조공학회지
• /
• 제3권2호
• /
• pp.100-105
• /
• 1983

The mechanism of coal-dust action on inhibiting burn-on of Sand to iron castings was taken in consideration by means of casting test and thermal decomposition test. To compare the ability of inhibiting sand burn-on, test castings were produced in green sand moulds added three different coal-rusts. And quantitative determination of lustrous carbon and volatiles production for coal-dust samples were performed.The lustrous carbon production was in good agreement with the casting test result. But total voltiles production was relatively inefficient on hibiting sand burn-on to test castings.The lustrous carbon theory can be given to explain the mechanism which coal-dust inhibits sand burn-on to iron castings.

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 2003년도 추계학술대회 논문요약집
• /
• pp.158-158
• /
• 2003

• Korean Chemical Engineering Research
• /
• 제44권2호
• /
• pp.136-148
• /
• 2006

주물공장에서는 주철을 녹여서 다양한 기계부품을 만든다. 다양한 기계부품을 만들기 위해 목형을 주물사에 넣은 후 주입구를 만들어 녹인 주철을 투입한다. 주물공장은 furan 공정을 포함해 많은 공정으로 이루어지며, 이 중 furan 공정은 목형에 주물사를 부어 넣는 공정이다. Furan 공정의 첫 단계는 주물사가 서로 엉겨 붙어 있게 하기 위해 접착성을 가지는 고분자 물질인 furan류를 주물사에 섞게 되고 녹은 주철이 목형으로 들어가는 것이며 고온에 의해 많은 유해 VOC류가 발생하게 된다. 또 공정조업에서 furan용 모래를 목형이 든 주물형틀에 부어 넣게 되고, 이때도 유독가스와 분진이 발생하게 되며 이 분진은 furan 물질을 포함하고 있어 조업자의 건강에 치명적인 요소가 되며, 이로 인해 조업기피현상이 심화되어 인력수급에 문제가 되고 나아가 사업 경영에 큰 걸림돌이 되고 있다. 본 연구는 이러한 조업기피의 원인을 제거하고 쾌적한 조업환경을 제공하기 위해 유해 VOC류와 집진을 동시에 수행할 수 있는 유해 VOC 및 분진 동시제거 시스템을 최적 설계하고 나아가 현장에 적용 설치하였다. 그 결과 설치 후 포름알데히드의 경우 VOC 0 ppm, 분진 $4{\mu}g/m^3$으로 조업환경이 개선되었으며, 조업자들의 조업 기피 요인을 해소하였다. 또한, 우리는 회사의 고용 문제를 해결하고, 작업의 생산성을 향상시킬 수 있었다.

• 한국대기환경학회지
• /
• 제22권1호
• /
• pp.35-41
• /
• 2006

The steel foundries with electric arc furnaces handling metal scraps have recently gained an attention as a potential source of dusts. The present study focuses on the analysis of dust emissions and removals during furnace charging and melting processes by commercial CFD software named FLUENT. A body fitted grid system consisting of 880,000 meshes was first generated by Gambit for the electric arc furnace with the capacity of 60 ton/cycle and then FLUENT was invoked to solve the corresponding NavierStokers equation for the momentum, temperature and dust concentration. The entire processes from metal charging to metal melting were simulated to investigate the unsteady behaviors of fluid flows and dust concentrations. The model simulation results showed that as the top of the electric arc furnace opened for metal charging, hot plumes bursted out from the furnace rose strongly by buoyance and escaped mostly through the main hood. Therefore, the capacity of main hoods determined the vent efficiency in the metal charging process. As the furnace was closed after the metal charging and the metal melting processes was followed, the hot flow stream stretching from the furnace to the main hood was dissipated fast and the flow from the inlet of the bottom of the left hand side to the main and monitoring hoods constituted the main stream. And there was only a slow flow in the right hand side of the furnace. Therefore, the dust concentrations were calculated higher in the left hand side of the furnace, which was consistent with observations.

• Journal of Preventive Medicine and Public Health
• /
• 제27권2호
• /
• pp.274-285
• /
• 1994

The effects of resin on the respiratory health have been investigated in 309 workers from four iron and steel foundries and the results compared with those from 122 workers who were not significantly exposed to resin gas and silica dust at the same industries. Phenol-formaldehyde resin was used in the core making and molding processes and workers were exposed to their decomposition products as well as to silica dust containing particulates. The subjects were grouped according to formaldehyde, dust and other gas exposures, and smoking habits were considered also in thi analysis. Standardized respiratory symptom questionnaire was administered by trained interviewers. Chest radiograph, pulmonary funtion tests, and methacholine challenge tests were done. Environmental measurements at the breathing zone were carried out to determine levels of formaldehyde, respiable dust and total dust. Foundry workers had a higher prevalence of symptoms of chronic bronchitis with chronic phlegm and chronic cough when exposed to dust. Exposure to gas was significantly associated with lowered $FEV_1$ and obstructive pulmonary function changes. Exposure to formaldehyde and phenol gas was associated with wheezing symptom among workers, but $FEV_1$ changes after methacholine challenge were not significantly different among different exposure groups. When asthma was defined as the presence of bronchial hyperreactivity with more than 20% decrease in $FEV_1$ after methacholine challenge, 17 workers out of 222 tested had asthma. Fewer asthmatic welters were found among groups exposed to formaldehyde, gas and dust, which indicates a healthy worker effects ill a cross-sectional study. The concentration of formaldehyde gas ranged from 0.24 to 0.43 ppm among studied foundries. The authors conclude that formaldehyde and phenol gas from combusted resin is probably the cause of asthmatic symptoms and also a selection force of those with higher bronchial reactivity away from exposures.