• Korean Journal of Materials Research
• /
• v.3 no.6
• /
• pp.652-660
• /
• 1993

It was investigated to obtain the relationship between magnetic properties and conditions of forming $Fe_{3}C$ single phase from acicular goethite by heat treatment under the atmosphere of CO and $N_{2}$ mixed gas. X-ray analyses, TEM and VSM measurements were imployed for the characteristics of the carbide. Acicular goethite was sinthesized under proper process parameters. $Fe_{3}C$ single phase was obtained above $550^{\circ}C$, 60min. and $Fe_{5}C_2$ was formed with $Fe_{3}C$ below that temperature. The soturation magnetization of $Fe_{3}C$ single phase was about 100emu/g regardless of the reaction temperature. The coersive force and the ratio of Mr/Ms decreased respectively from 780 to 400 Oe. and from 0.35 to 0.13 with increasing reaction temperature.

• Journal of the Korean Society for Precision Engineering
• /
• v.30 no.6
• /
• pp.589-595
• /
• 2013

Solution processed conjugated molecules enable to manufacture various electronic devices by unconventional and cost effective patterning methods as screen or gravure printing. Spin-coating is the most popularly used method to form conjugated polymeric film for various electronic devices. The coating method has certain disadvantages such as a large amount of unwanted wastes, difficulty forming a film with a large area, and impossible to apply roll-to-roll manufacturing. We present here a promising alternative coating method, bar-coating for conjugated polymer film and OLED with the bar coated light emitting layer. In this papers, we show atomic force microscope images of spin- and bar-coated Poly[(9,9-di-n-octylfluorenyl-2,7-diyl)-alt-(benzo[2,1,3]thiadiazol-4,8-diyl)] (F8BT) films on substrate. The bar-coated film showed a slight lower RMS roughness (1.058 [nm]) than spin-coated film (1.767 [nm]). It means the bar-coating is suitable method to form light emitting layers in OLEDs. By using bar-coating process, an OLED obtained with 4.7 [cd/A] in maximum current efficiency.

• The korean journal of orthodontics
• /
• v.20 no.1
• /
• pp.61-86
• /
• 1990

To study the effect of prostglandin $E_2$ and evening primrose oil on orthodontic tooth movement in rats, one hundred and sixty rats were divided into four groups of 40 rats each. One group, injected with saline on the palate subperiosteally, served as a control group. A second and third group were injected subperiosteally on the palate with $PGE_2$ $10{\mu}g$ and evening primrose oil 10mg respectively. The fourth group was given indomethacin $20{\mu}g/m{\ell}$ orally by water bottle. The maxillary first molar was moved mesially from the incisors using a 50gm force rubber band. In each group at the 1, 2, 3, 5, and 7th day, 4 rats were examined by light microscope, and 4 by electron microscope. The obtained results were as follows: 1. Osteoclastic activity was maximum at the 3rd day in the $PGE_2$ group on the interradicular alveolar bone of the first molar, followed by the evening primrose oil group, control group, and indomethacin group. 2. Root resorption and vacuolar changes were maximum in the $PGE_2$ group. 3. At the 3rd day of the $PGE_2$ group, the osteoclasts showed well developed ruffled borders and clear zones. At the same day, the evening primrose oil group also showed well developed ruffled borders and clear zones, but less than the $PGE_2$ group. 4. At the 3rd and 5th day of the $PGE_2$ group, fibroblasts showed phagocytized fragmented collagen fibers in the cytoplasm. At the 7th day of the $PGE_2$ group, fibroblasts showed collagen fibers forming at the cell membrane surface.

• Journal of the Computational Structural Engineering Institute of Korea
• /
• v.28 no.2
• /
• pp.207-212
• /
• 2015

Bridges are designed and constructed as infrastructures in order to overcome topographical obstructions for fast and smooth transfer of human/material resources. Therefore the shape and size of piers constructed along the longitudinal bridge axis should be restricted by topographical conditions. Action forces of connections and piers are affected by pier shapes and sizes together with connection arrangement which decides load carrying path under earthquakes. In this study a typical bridge is modelled with steel bearings and reinforced concrete piers and seismic analyses are performed with analysis models with different arrangement of steel bearings and piers. From analysis results ductile failure mechanisms for all analysis models are checked based on strength/action force ratios of steel bearings and pier columns. In this way the influences of arrangement of connections and piers on the earthquake resistant capacity of typical bridges are figured out in view of forming ductile failure mechanism.

• Korean Journal of Crystallography
• /
• v.5 no.2
• /
• pp.108-112
• /
• 1994

C19H20O5, Mr=314.337, triclinic,PI, a=10.291(2)A, b=11.218(3)A, c=3.059(1)A, α=74.54(2)°, β=1148.84(1)°, r=109.84(2)°, V=883.283(2)A3, λ(Mo Kα)=0.71069A, μ=0.47 mm-1, F(000)=324, 296K, Z=2, Dx=1.18Mgm-3. Final R=0.0580 for 1637[F>3σ(F)]unique refledtions. α,β-diphenylsuccinic acid, C16H14O4, are connedted with the solvent actone by hydrogen bond O(4)-H˙˙˙O(5), forming a dimer related by related by centrosymmentry thorough intermolecualr carboxylic hydrogen bond O(1)-H˙˙˙O(2)(-x,-y,-z). The nearest distance 3.288A[O(2)˙˙˙O(2)(-x,-y,-z)] between the dimers shows that the packing of the dimer is govermed by van der Waals'force.

• The Research Journal of the Costume Culture
• /
• v.25 no.2
• /
• pp.192-205
• /
• 2017

Modern men are much more interested in their appearance than ever before, as well as showing an increased need for uniqueness in order to construct their own sphere and pursue differentiation from others. Besides, changes in life style and the aesthetic sense are causing men to pursue various kinds of clothing benefits so that they want a suit with characteristics beyond the stereotyped design and style. They have started to be actively engaged in clothing purchases, forming a driving force for the growth of the male suit market. Hence, this study has significance in that it offers data conducive to consumers' custom suit purchase by reviewing data on the present condition of the custom suit market and bespoke suits. In addition, it aims to give a summary on the theoretical bases of preceding studies, including the need for uniqueness, pursuit of clothing benefit and concern for the appearance of male consumers, as well as examining the factors that influence on their bespoke suit purchase intentions. Accordingly, this work intends to construct a basic environment for consumers to approach the custom suit market easily and pave the way for male suit markets through offering marketing data and information that is helpful for custom suit-related markets.

• Geomechanics and Engineering
• /
• v.16 no.4
• /
• pp.385-397
• /
• 2018

This study evaluates the interfacial properties of composite specimens consisting of shotcrete and sprayed waterproofing membrane. Two different membrane prototypes were first produced and tested for their waterproofing ability. Then composite specimens were prepared and their interfacial properties assessed in direct shear and uniaxial compression tests. The direct shear test showed the peak shear strength and shear stiffness of the composites' interface decreased as the membrane layer became thicker. The shear stiffness, a key input parameter for numerical analysis, was estimated to be 0.32-1.74 GPa/m. Shear stress transfer at the interface between the shotcrete and membrane clearly emerged when measuring peak shear strengths (1-3 MPa) under given normal stress conditions of 0.3-1.5 MPa. The failure mechanism was predominantly shear failure at the interface in most composite specimens, and shear failure in the membranes. The uniaxial compression test yielded normal stiffness values for the composite specimens of 5-24 GPa/m. The composite specimens appeared to fail by the compressive force forming transverse tension cracks, mainly around the shotcrete surface perpendicular to the membrane layer. Even though the composite specimens had strength and stiffness values sufficient for shear stress transfer at the interfaces of the two shotcrete layers and the membrane, the sprayed waterproofing membrane should be as thin as possible whilst ensuring waterproofing so as to obtain higher strength and stiffness at the interface.

• Proceedings of the Materials Research Society of Korea Conference
• /
• 2009.11a
• /
• pp.39.1-39.1
• /
• 2009

NiTi alloy is widely used innumerous biomedical applications (orthodontics, cardiovascular, orthopaedics, etc.) for its distinctive thermomechanical and mechanical properties such as shape memory effect, super elasticity, low elastic modulus and high damping capacity. However, NiTi alloy is still a controversial biomaterial because of its high Ni content which can trigger the risk of allergy and adverse reactions when Ni ion releases into the human body. In order to improve the corrosion resistance of the TiNi alloy and suppress the release of Ni ions, many surface modification techniques have been employed in previous literature such as thermal oxidation, laser surface treatment, sol-gel method, anodic oxidation and electrochemical methods. In this paper, the NiTi was electrochemically etched in various electrolytes to modify surface. The microstructure, element distribution, phase composition and roughness of the surface were investigatedby scanning electron microscopy (SEM), energy-dispersive X-ray spectrometry(EDS), X-ray diffractometry (XRD) and atomic force microscopy (AFM). Systematic controlling of nano and submicron surface features was achieved by altered density of hydro fluidic acid in etchant solution. Nanoscale surface topography, such as, pore density, pore width, pore height, surface roughness and surface tension were extensively analyzed as systematical variables.Importantly, bone forming cell, osteoblast adhesion was increased in high density of hydro fluidic treated surface structures, i.e., in greater nanoscale surface roughness and in high surface areas through increasing pore densities.All results delineate the importance of surface topography parameter (pores) inNiTi to increase the biocompatibility of NiTi in identical chemistry which is crucial factor for determining biomaterials.

• KSCE Journal of Civil and Environmental Engineering Research
• /
• v.8 no.1
• /
• pp.33-40
• /
• 1988

The new technique has been used to determine the soil-reinforcement interaction. The testing apparatus is essentially a triaxial cell fitted with the capability to house a hollow cylinderical sample. A hollow cylinderical sand specimen with a concentrical layer of reinfarcing material sandwitched in the middle is used in this investigation. The reinforcement is fastened at the base. The hollow specimen can be viewed as a "unit sheet" of a soil-reinforcement composite system of infinite horizontal extent. Axial load as well as inner and outer chamber pressures can be applied to perform a test. The specimen is first subjected to an isotropic stress state corresponding to the overburden pressure. Next, an extension test by reducing the axial load is carried out. The specimen is "loaded" to failure by either the breakage of reinforcing material (tensile failure) or slippage which takes place at the soil-reinforcement interface (i.e. the overcoming of the bonding capacity). Since the reinforcement is fastened at its lower end to the base, any tendency of relative movement between the reinforcement and the sand during an extension test can induce tensile force in the reinforcement thus forming a "reversed pull-out" test condition. Preliminary test results have demonstrated positively of the new approach to test the soil-reinforcement interaction. Reinforcing elements of different extensibility were used to study the deformbility of reinforced soil. Furthermore, both the breakage and the pull-out modes of failure were observed.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2005.06a
• /
• pp.1223-1227
• /
• 2005

Fine microgroove is the key component to fabricate micro-grating, micro-grating lens and so on. Conventional groove fabrication methods such as etching and lithography have some problems in efficiency and surface integrity. This study deals with the creation of ultra-precision micro grooves using non-rotational diamond tool and CNC machining center. The shaping type machining method proposed in the study allows to produce V-shaped grooves of $40\mu{m}$ in depth with enough dimensional accuracy and surface. For the analysis of machining characteristics in micro V-grooving, three components of cutting forces and AE signal are measured and processed. Experimental results showed that large amplitude of cutting forces and AE appeared at the beginning of every cutting path, and cutting forces had a linear relation with the cross-sectional area of uncut chip thickness. From the results of this study, proposed micro V-grooving technique could be successfully applied to forming the precise optical parts like prism patterns on light guide panel of TFT-LCD.