• Clean Technology
• /
• v.19 no.3
• /
• pp.313-319
• /
• 2013

To produce biodiesel efficiently from fish oil containing 4% free fatty acid, esterification and trans-esterification were carried out with Vietnam catfish oil, which was kindly provided from GS-bio company. Heterogeneous solid acid catalysts such as Amberlyst-15 and Amberlyst BD-20 and sulfuric acid as homogeneous acid catalyst were used for the esterification of free fatty acids in the fish oil. Sulfuric acid showed the highest removal efficiency of free fatty acid and the shortest reaction time among three acid catalysts. The base catalysts for trans-esterification such as KOH, $NaOCH_3$ and NaOH were compared with each other and KOH was determined to be the best transesterification catalyst. Some solid material, which assumed to be saponified product from glycerol and biodiesel, were observed to form in the fish oil biodiesel when using $NaOCH_3$ and NaOH as the transesterification catalyst. The initial acid value of fish oil was proven to have a negative effect on biodiesel conversion. Of the three catalysts, KOH catalyst transesterification was shown to have high content of FAME and the optimal ratio of methanol/oil ratio was identified to be 9:1.

• Journal of Environmental Science International
• /
• v.14 no.2
• /
• pp.221-230
• /
• 2005

Catalytic wet oxidation of trichloroethylene (TCE) in water has been conducted using $TiO_2-supported$ cobalt oxides at $36^{\circ}C$ with a weight hourly space velocity of $7,500\;h^{-1}.\;5\%\;CoO_x/TiO_2$, prepared by using an incipient wetness technique, might be the most promising catalyst for the wet oxidation although it exhibited a transient behavior in time on-stream activity. Not only could the bare support be inactive for the wet decomposition reaction, but no TCE removal also occurred by the process of adsorption on $TiO_2$ surface. The catalytic activity was independent of all particle sizes used, thereby representing no mass transfer limitation in intraparticle diffusion. XPS spectra of both fresh and used Co surfaces gave different surface spectral features for each $CoO_x,\;Co\;2P_{3/2}$ binding energy for Co species in the fresh catalyst appeared at 781.3 eV, which is very similar to the chemical states of $CoTiO_x$ such as $CO_2TiO_4\;and\;CoTiO_3$. The used catalyst exhibited a 780.3-eV main peak with a satellite structure at 795.8 eV. Based on XPS spectra of reference Co compound, the TCE-exposed Co surfaces could be assigned to be in the form of mainly $Co_3O_4$. XRD patterns for $5\%\;CoO_x/TiO_2$ catalyst indicated that the phase structure of Co species in the catalyst even before reaction is quite comparable to the diffraction lines of external $Co_3O_4$ standard. A model structure of $CoO_x$ present predominantly on titania surfaces would be $Co_3O_4$, encapsulated in thin-film $CoTiO_x$ species consisting of $Co_2TiO_4$ and $CoTiO_3$, which may be active for the decomposition of TCE in a flow of water.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2008.11a
• /
• pp.145-145
• /
• 2008

High-k materials have been paid much more attention for their characteristics with high permittivity to reduce the leakage current through the scaled gate oxide. Among the high-k materials, $ZrO_2$ is one of the most attractive ones combing such favorable properties as a high dielectric constant (k= 20 ~ 25), wide band gap (5 ~ 7 eV) as well as a close thermal expansion coefficient with Si that results in good thermal stability of the $ZrO_2$/Si structure. During the etching process, plasma etching has been widely used to define fine-line patterns, selectively remove materials over topography, planarize surfaces, and trip photoresist. About the high-k materials etching, the relation between the etch characteristics of high-k dielectric materials and plasma properties is required to be studied more to match standard processing procedure with low damaged removal process. Among several etching techniques, we chose the inductively coupled plasma (ICP) for high-density plasma, easy control of ion energy and flux, low ownership and simple structure. And the $BCl_3$ was included in the gas due to the effective extraction of oxygen in the form of $BCl_xO_y$ compounds. During the etching process, the wafer surface temperature is an important parameter, until now, there is less study on temperature parameter. In this study, the etch mechanism of $ZrO_2$ thin film was investigated in function of $Cl_2$ addition to $BCl_3$/Ar gas mixture ratio, RF power and DC-bias power based on substrate temperature increased from $10^{\circ}C$ to $80^{\circ}C$. The variations of relative volume densities for the particles were measured with optical emission spectroscopy (OES). The surface imagination was measured by scanning emission spectroscope (SEM). The chemical state of film was investigated using energy dispersive X-ray (EDX).

• Journal of the Korean Association of Oral and Maxillofacial Surgeons
• /
• v.30 no.2
• /
• pp.157-161
• /
• 2004

The eyes, the saying goes, are the windows of the soul. It's the first thing you notice about a person. Therefore, many people want to possess beautiful eyelids. Surgical formation of a palpebral fold and sulcus divides the lid into two well-defined segments (palpebral and pretarsal), producing the double eyelid desired by many Oriental women as well as an increasing number of man recently. Upper lid blepharoplasty is the Oriental eye is one of the variations of standard upper lid blepharoplasty. In Oriental double eyelid surgery, there have been two approaches to form a superior palpebral fold: the buried suture(nonincision) method and the full external incision method. Conventionally, the nonincision technique has been shown to produce little postoperative edema. However, the probability of the fold disappearing is high, and this technique cannot be performed in patients with fatty eyelids. Conversely, the incision technique has contrary characteristics. Recently, partial incision(or semi-open) technique which is combination of mentioned methods is used, this technique is removal of pretarsal tissue, muscle, and/or orbital fat around 2 or 3 incision site to facilitate tarsus-dermal adhesion. Our method is on the basis of this technique, furthermore, compared with conventional semi-open method, Y(Yang's) needle assisted double eyelid operation is more easy, convenient, saving-time method and provide satisfactory results.

• KSCE Journal of Civil and Environmental Engineering Research
• /
• v.33 no.4
• /
• pp.1463-1469
• /
• 2013

Portland cement used as binding material in combination of ferrous iron for reductive dechlorination of chlorinated organics is already widely studied topic by several researchers. However there is no clear evidence about the component solely responsible in cement for trichloroethylene (TCE) dechlorination. Many researchers suspect that the ettringite, monosulfate phases associated with hydration of cement are responsible active agents for TCE dechlorination. This study deals with synthesizing different pure crystalline minerals like ettringite and monosulfate phases of cement hydration and check individual phase's TCE dechlorinating capacity in combination with ferrous iron. The results indicated that the synthesized minerals showed no reduction capacity for TCE. The findings in the present study is significant as it shows that ettringite and monosulfate phases which were suspected minerals by previous researchers for TCE dechlorination are not reactive. Hence it is suspected that some other mineral or mineral form in cement phase could be responsible for TCE degradation.

• Journal of Korean Society of Water and Wastewater
• /
• v.18 no.3
• /
• pp.392-400
• /
• 2004

This research uses the $TiO_2$/UV process to verify the most suitable condition and possibility to dispose dyeing wastewater that contains pigment and a large amount of pollutants. For this, this research has enforced experiments that compare photo adsorption, photolysis, and photo catalyst oxidation reaction, and also evaluated and analyzed the change of pH and $TiO_2$ dosage, irradiation rates of ultraviolet rays and the dosage change and injection method of $H_2O_2$. According to the results of the dyeing wastewater experiment of storehouse catalyst that uses the new form of $TiO_2$, the photo catalyst oxidation reaction proved to be more effective than photo adsorption and photolysis; 35%, 21% in the case of $TCOD_{cr}$ and 39%, 28% in the case of chromaticity. Taking into consideration the reaction time, amount of photo catalyst reaction and irradiation amount of ultraviolet rays, the decomposition efficiency of pH change proved to be most effective at pH 4. On the whole, the acidity area proved to be effective in dyeing water exclusion than neutral and alkalinity areas. Having evaluated the influence of $TiO_2$ dosage, not only does the decomposition efficiency continuously improve as the $TiO_2$ dosage increases but the shielding effect does not occur also when the $TiO_2$ is at a fixed state. The influence of ultraviolet irradiation amount concluded in the result that as the ultraviolet irradiation amount increases the decomposition efficiency continually increased, but in the case of chromaticity when the irradiation amount was higher than 37.8mW/cm2 the removal efficiency is slowed remarkably. The influence of $H_2O_2$ dosage evaluation reached the results that although the decomposition efficiency increases with the increase of $H_2O_2$ dosage, when above 150mg (total dosage: 1200mg) $H_2O_2$ consumes OH radical itself and reduces the decomposition efficiency. Also in the case of the $H_2O_2$ injection method rather than injecting in the whole amount of $H_2O_2$ (1200mg) needed at the beginning all at once, injecting divided quantities of $H_2O_2$ whenever the electric current density falls below 10mgfl reduces the wases of OH radical due to an excess of $H_2O_2$ and in tum heightens the decomposition efficiency.

• Journal of the Korean Ceramic Society
• /
• v.39 no.8
• /
• pp.801-806
• /
• 2002

The decomposition and/or conversion of carbon dioxide to carbon have been studied using oxygen-deficient ferrites for the reduction of $CO_2$ emission to the atmosphere. In this work, the homogeneous precipitation method using urea decomposition was employed to induce in situ precipitation of Ni ferrite($Ni_{0.4}Fe_{2.6}O_4$) on the porous ceramic fiber support (50 mm diameter${\times}$10 mm thickness). Effects of ferrite loading conditions on the CO2 decomposition efficiency were discussed in this paper. Removal of residual chloride ions and urea by solvent exchange from the porous media after ferrite deposition apparently helps to form spinel ferrite, but does not increase the efficiency of $CO_2$ decomposition. Porous ceramic fiber composites containing 20 wt% (1g) ferrite samples showed 100% efficiency for $CO_2$decomposition during the first three minutes, but the efficiency decreased rapidly after the elapsed time of ten minutes. The characteristic reduction time for the $CO_2$ decomposition efficiency was estimated as about 3∼7 min.

• Asian-Australasian Journal of Animal Sciences
• /
• v.15 no.9
• /
• pp.1257-1262
• /
• 2002

The objective was to identify the appropriate form of progesterone, which exhibits compact reproductive responses in Awassi ewes during mid to late seasonal anestrous period. Forty-eight Awassi ewes were randomly allocated into four groups to be treated with 60 mg medroxyprogesterone acetate (MAP), 30 mg fluorogestone acetate (FGA), 40 mg FGA, or 600 mg progesterone sponges. After a 12 day period, sponges were removed and ewes were administered i.m. with 600 IU PMSG (d 0, 0 h). Five harnessed Awassi rams were turned-in with the ewes to detect heat. Ewes were checked for breeding marks at 6 h intervals for 5 days. Blood samples were collected from all ewes for analysis of progesterone concentrations. Pretreatment (d -13 and -12) progesterone concentrations were ${\leq}0.2ng/mL$ among all ewes and were indicative of seasonal anestrous period. On d 0, progesterone concentrations were elevated to $1.4{\pm}0.1ng/mL$ in ewes received progesterone sponges only and were higher (p<0.0001) than those (${\leq}0.2ng/mL$) administered MAP or FGA sponges. Progesterone concentrations returned to their basal values of <0.2 ng/mL within 24 h of sponge removal and were similar (p>0.1) among all ewes. Incidence of estrus was similar (p>0.1) among the four groups and occurred in 75% (9/12), 82% (9/11), 67% (8/12) and 58% (7/12) of the ewes receiving MAP, 30 mg FGA, 40 mg FGA and progesterone sponges, respectively. Estrous responses occurred 14.7, 20 and 13.6 h earlier in progesterone-sponge-treated ewes than those of MAP- (p<0.04), 30 mg FGA- (p<0.01) and 40 mg FGA-treated (p=0.06) ewes, respectively. Induced estrus conception rates were 50% (6/12), 55% (6/11), 50% (6/12) and 42% (5/12), out of which 4/6, 4/6, 3/6 and 3/5 lambed 151 days following d 0, and were similar (p>0.1) among ewes of the four treatment groups. Ewes that returned to estrus 16 to 20 days following d 0 were 5/12, 5/11, 6/12 and 4/12 ewes treated with MAP, 30 mg FGA, 40 mg FGA and progesterone sponges, respectively, and all lambed 169 days later. Overall lambing rates were 75% (9/12), 82% (9/11), 75% (9/12) and 58% (7/12) ewes treated with MAP, 30 mg FGA, 40 mg FGA and progesterone sponges, respectively. Results demonstrate that applications of MAP, 30 mg FGA, 40 mg FGA and progesterone sponges Awassi ewes were equally effective in induction of estrus and tended to favor both types of FGA and MAP in overall lambing rates over progesterone sponges during the seasonal anestrous period.

• Maxillofacial Plastic and Reconstructive Surgery
• /
• v.11 no.2
• /
• pp.53-59
• /
• 1989

The ameloblastoma is the most common form of the odontogenic tumors exhibiting minimal inductive change in connective tissue, it comprising 1% of all tumor and cysts of the jaws. It is a true neoplasm, generally considered to be a benign but persistent or, locally malignant lesion. The tumor occurs most commonly in persons between the age of 20 and 50 years. 80% and 90% of all lesions are in the mandible. The presenting clinical signs and symptoms of the ameloblastoma very from patient to patient, but most common symptom was swelling, followed by pain, draining sinuses, and superficial ulcerations. It is slow-growing lesion, and the radiographic features of the ameloblastoma depend large one the nature and the local bone reaction to the particular tumor. Recurrence rate is about 33%, but this is probably due to incommplete initial removal of lesion. We had operated a patient ; 29-year-old female immediate reconstruction combined with autocompression plate and iliac bone graft and screw fixation after hemimandibulaectomy with recurred ameloblastoma involving from premolar to ascending ramus at right side mandible. We obtained favorable results of good function, short intermaxillary fixation periods and easy operation precedure than the other reconstruction methods.

• Korean Chemical Engineering Research
• /
• v.44 no.4
• /
• pp.375-381
• /
• 2006

In this sturdy, spherical activated carbon(SPAC) contained $TiO_2$ was made by ion-exchanged treatment and heat treatment for applying fluidizing bed system. The ion-exchange resin was treated by $TiCl_3$ aqueous solution. The treated resin and raw resin were heat-treated under nitrogen condition to convert into Ti-SPAC. During the heat-treatment, burn-off weight amounts and the element were measured by means of TGA and TGA/MS, individually. The physicochemical properties of Ti-SPAC was characterized by means of XRD, SEM, EDS, BET, EPMA, ESR, intensity and titanium content. The Ti-SPAC had spherical shape with diameter size about $350{\mu}m{\sim}400{\mu}m$ and $617m^2/g$ specific surface area. Structure of $TiO_2$ in Ti-SPAC was anatase and rutile form. Also, $TiO_2$ on SPAC were found that the $TiO_2$ were uniformly distributed through EPMA analysis. Moreover, the Ti-SPAC showed indirect photocatalyst activity estimation through ESR analysis, characteristics of photocatalyst potentially. Over all results, Ti-SPAC was used in fluidizing bed UV/photocatalyst system to remove HA(Humic Acid). That results were HA removal efficiency was about 70％ and Ti-SPAC intensity was preserved during reaction. Ti-SPAC showed practical possibility as photocatalyst in fluidizing bed system.