• The Research Journal of the Costume Culture
• /
• v.22 no.2
• /
• pp.339-345
• /
• 2014

This study analyzes and compares Hanji made with loess to Hanji made with kaolin, two yellow-based inorganic pigments, in terms of its physical properties, optical properties, and color fastness to light with the aim of using it as a fashion material. Hanji made by adding inorganic pigments showed an approximately 20% retention ratio on average. This figure was similar to those of loess and kaolin. Physical properties were analyzed, with the following results. A higher amount of additives lowered the apparent density and increased thickness and bulk. In general, inorganic pigment-added Hanji had lower tensile strength, bursting strength, and folding endurance compared to non-additive Hanji. The analysis of optical properties showed a lower brightness index for Hanji made with inorganic pigments compared to non-additive Hanji. When comparing the two inorganic pigments, the brightness of Hanji made with kaolin was higher. Regarding color fastness to light, loess showed level 4 and kaolin showed level 5 when 25% inorganic pigments on pulp were added to Hanji. Thus, Hanji made by adding inorganic pigments during the manufacturing process may perform well as materials for fashion because the additives enhanced both the color fastness to light and the bulk while maintaining the strength. In addition, Hanji dyed with inorganic pigments may have the potential to serve as materials for the fashion industry while still retaining the characteristics of Hanji.

• Journal of the Korea Furniture Society
• /
• v.17 no.1
• /
• pp.23-32
• /
• 2006

This study was carried out to explore a new application of traditional Hanji and obtain fundamental properties for producing Hanji wallpaper by incorporating ceramics from wood and rice-husk as an interior building material. The results of properties determined were summarized as follows: The addition of ceramics in Hanji paper reduced its apparent density, but increased bulk density due to the ceramic particles distributed on the surface and inside the fiber of Hanji wallpapers. In particular, woodceramic particles were specifically distributed on the fiber surface, while particles of rice-husk ceramics were permeated into the inside surface of fibers. The density of rice-husk ceramics were greater than that of woodceramics. The physical properties of Hanji wallpapers, such as breaking strength, wet breaking strength, burst strength, tear index and folding endurance were deteriorated with the addition of ceramics. However, the addition of woodceramics in the Hanji wallpaper resulted in better strength in most cases than that of rice-husk ceramics, except tear strength. Therefore, an optimum addition level of woodceramics into the wallpaper was found to be 5% on the basis of intensity. The addition of ceramics also prolonged the combustion time because it lowered air permeability and brightness of the wallpaper.

• Journal of Korea Technical Association of The Pulp and Paper Industry
• /
• v.41 no.3
• /
• pp.60-64
• /
• 2009

Paper is easily damaged by physical and chemical deterioration under several factors. Damaged paper cultural heritage is usually restored by Lining. A traditional method of Lining is attaching the lining paper behind the original paper cultural heritage using starch and water. It supports the weakened quality of paper. In Japan, paper cultural heritage is restored with "Washi" which is made from mixture of Paper mulberry and Japanese cedar. In the west, the lining paper made from Paper mulberry, which has extraordinary excellent conservativeness, is usually used as a restoration material for paper. But Japanese Washi has dominated the demand for restoration materials as the most preferred restoration paper, and most kinds of paper made from Paper mullbery have been called as 'Japanese paper'. Result showed that the strength of the Korean lining papers was generally higher than that of the Japanese ones. As a result from measuring the rate of dimensional change after water-immersion and drying, sample B of the Korean lining papers and sample E of the Japanese lining papers showed the highest stability.

• Journal of Korea Technical Association of The Pulp and Paper Industry
• /
• v.46 no.5
• /
• pp.88-97
• /
• 2014

For the purpose of reproduction of traditional gold thread, the artifact investigation was organized for 70 cases (109 pieces) of relics from Korea, China and Japan. In most cases, the main backside material of gold thread from Korea was the bast fibers from paper mulberry. In this study, the optimum sheet-making of Hanji for gold thread reproduction was tried by controlling several process factors of Hanji such as the cooking and beating time of paper mulberry fibers, the number of sheet-making ply, and converting method (Dochim). Tensile index, folding endurance and compressive strength of Hanji showed differences according to the correlation between cooking and beating time, and application of converting method (Dochim), while bending stiffness fell with decrease of thickness. These results can be applied to consider manufacturing factors to make Hanji for the production of gold thread.

• Journal of Korea Technical Association of The Pulp and Paper Industry
• /
• v.47 no.4
• /
• pp.115-126
• /
• 2015

In this study, we investigated influence of ground calcium carbonate (GCC) modified by washless multilayering of polyelectrolytes on paper quality. Three layers of polyelectrolytes (cationic starch/anionic polyacrylamide/cationic starch) were formed on the surface of GCC using laboratory inline washless polyelectrolytes multilayering system, which was called inline LbL GCC. Base papers were prepared with untreated GCC or inline LbL GCC using a laboratory handsheet former. These handsheets were coated with rod coater, and then printed by black ink. Properties of base paper and fold crack of coated paper were evaluated. Base paper with inline LbL GCC showed much higher mechanical strength in terms of tensile index, strain, internal bond strength, and folding endurance. The fold crack of coated paper with inline LbL GCC occurred more frequently compared to coated paper with untreated GCC. This might be due to highly improved internal bond strength of base paper, which resulted in smaller delamination that played a role of stress dissipation. It would be recommended to design a proper coating layer in order to prevent fold crack.

• Advanced Composite Materials
• /
• v.18 no.4
• /
• pp.315-326
• /
• 2009

PCC (precipitated calcium carbonate) and ground calcium carbonate have been widely used in alkaline papermaking. Unfortunately, although increasing filler level in papers can improve the paper properties such as brightness, opacity, stiffness gloss, smoothness, porosity, and printability, as well as decrease cost, some strength of the paper is negatively affected. In this research, needle-like aragonite was synthesized using $Ca(OH)_2$ and $CO_2$ as reactants in the presence of $MgCl_2$ and characterized with scanning electronic microscopy (SEM) and X-ray diffraction (XRD). The physical and optical properties of the paper handsheets containing these needle-like aragonite fillers were evaluated. Results indicated that tensile strength, Z-direction tensile strength and folding endurance of the paper were improved by the needle-like aragonite crystals compared to the paper using commercial PCC (precipitated calcium carbonate) as filler. The stiffness of the paper handsheet on the machine direction was increased, but no evident difference in the cross direction was found. The improvement of paper strength mainly resulted from the twining effect between the aragonite whiskers and paper fibers. The optical properties of the paper were slightly decreased with the use of the needle-like aragonites compared to commercial PCC. These results suggest that paper cost can be decreased by increasing the content of needle-like aragonite filler while paper strength will not be decreased compared to PCC filler.

• Proceedings of the Korea Technical Association of the Pulp and Paper Industry Conference
• /
• 2007.04a
• /
• pp.257-263
• /
• 2007

본 논문은 내구성(durability) 및 내오염성(soiling resistance)이 매우 중요한 성질로 인식되는 유통지의 평가방법을 제안하는데 목적이 있다. 즉, 종이의 내구성 및 내오염성의 측정 및 평가에 있어서, 재현성 및 반복성이 우수하고 합리적인 측정방법 및 평가방법을 구축하는데 목적이 있다. 연구목적에 적합한 시료의 준비, 오염물의 조성, 실험장치 및 실험후의 타당한 평가방법 등에 대하여 선행 연구결과를 고찰하였다. 기존 방법의 수정과 새로운 장치의 제작 및 평가방법의 설정을 통해 재현성이 높은 평가방법을 정립하고자 하였다. 유통지의 내구성을 평가하는 방법으로는 습식, 내오염성, 건식 내오염성, 구김기공도, 내세탁성, 잉크 내마모도 등의 항목을 측정하여 개별항목으로 내구성을 가늠하거나, 몇가지항목에 각기 다른 가중치를 부여하여 구한 내구성 지수(durability index)의 개념으로 내구성을 평가하기도 한다. 본 논문에서는 내구성에 영향하는 요소로 강도적 성질요소(strength property value)와 내오염성 요소(artificial soiling value)로 구분하였다. 강도적 성질요소에서는 전통적으로 내구성과 관련이 깊은 것으로 인식되어 온 내절도(folding endurance), 인열강도(tearing resistance) 및 구김기공도(crumpled porosity)를 인쇄하기 전 용지상태에서 측정하여 4:4:2의 가중치를 주어 구하였다. 내오염성 요소는 국가별 기후특성에 따라 연평균 상대습도가 60% 이상인 경우 인쇄 시료를 대상으로하여 습식 내오염성, 건식 내오염성 및 내석검성을 평가한 후 6:3:1의 가중치를 주어 구하였다. 또한 연평균 60% 미만인 국가의 경우 3:6:1의 가중치를 부여하였다. 이렇게 구해진 강도적 성질요소와 내오염성 요소에 있어 강도적 성질요소는 궁극적으로 내오염성 요소에 영향하기 때문에 3:7의 비율로 가중치를 부여하여 최종적으로 내구성 지수를 구하였다. 이때의 점수가 60점 이상이면 내구성 용지로 정의하였다. 본 논문에서는 현장실험을 통하여 시제품을 제조하였다. 상기 설명된 방법으로 내구성 지수를 구한 결과, 일반 유통지 제조방법으로 제조한 경우 내구성 지수가 약 45점이었다. 반면, 새로 개발된 방법에 의한 고내구성용지(durability paper)의 경우 70점 이상을 나타내어 내구성이 향상되었음을 확인할 수 있었다.

• Proceedings of the Korea Technical Association of the Pulp and Paper Industry Conference
• /
• 1999.04b
• /
• pp.386-389
• /
• 1999

Amphoteric polymers have brought to papermakers' attention gradually. In this paper, a series of amphoteric starches with different cationic and anionic degree of substitution (DS) are prepared. Better product has been selected and used under different condition. As retention and drainage aids, amphoteric starches were used in shorter fiber length, weak strength and poor drainage bleached AQ-Soda wheat straw pulp. In neutral and alkaline papermaking system, when amphoteric starches contain 0.024-0.026 anionic degree of substitution (DS), it is shown that the higher the cationic degree of substitution (DS) in amphoteric starches, the better the filler retention. The filler retention is improved 12.5%, 30.3%, and 35.1% and 32.5% respectively by adding 1% amphoteric starch LS-L2 -1 (0.034), LS-L2-2 (0.040), LS-L2-3 (0.047) and LS-L2-4 (0.052). But the strength of handsheets if affected a little. By adding 2% Al2 (SO4)3 and 1.5% LS-L2-3 at pH 7.5, filler retention can be improved from 38% to 80%, and breaking length of sheet only decreases 3.2%. As dry strengthening aids, amphoteric starches were used in eucalyptus APMP. Amphoteric starches are used in eucalyptus APMP. The amphoteric starch LS-L2-2 is better dry strength aid. Adding 1% LS-L2-2 can improve breaking length 24.5%, burst index 42.9%, tear index 38.8%, folding endurance and density of the handsheets.

• Journal of Korea Technical Association of The Pulp and Paper Industry
• /
• v.45 no.4
• /
• pp.1-8
• /
• 2013

High loading of printing and writing grades with fillers has many advantageous aspects in papermaking because it allows decreasing fiber use and reducing manufacturing cost. High loading technology, however, has some disadvantageous aspects as well. It decreases physical properties of papers, especially strength properties. The problem associated with high loading can be reduced by applying surface sizing starch solution onto paper surface. It is important to control the penetration of the surface sizing starch solution into paper web to obtain the desired property improvement. In this study, the effect of the addition of two polymers into starch solution on paper properties has been examined. PVOH and polyDADMAC were used as polymeric additives for surface sizing with oxidized starch. Viscosity of starch solutions and surface roughness of dried starch films on glass slides showed that some interactions between polymeric additives and oxidized starch have been occurred and the most extensive interaction with starch solution was obtained with high molecular weight polyDADMAC. Low molecular weight PVOH was most effective in improving folding endurance and internal bond strength. On the other hand, polymer addition showed no effect on surface strength of paper. This indicates that not the level of starch holdout but the bonding strength of starch itself has predominant influence on surface strength of paper.

• Journal of Korea Technical Association of The Pulp and Paper Industry
• /
• v.35 no.4
• /
• pp.8-16
• /
• 2003

The objective of this study was to investigate the potential application of the separated refining system in the papermaking process using cotton pulps. The cotton staple and linter fibers were expected to show a great difference in their refining responses due to their morphological and physical differences. Experiments were conducted to examine the differences in flocculation tendency, CED viscosity, fiber length, handsheet properties and the SEM surface images between staple and linter fibers at a given refining degree. These fibers were also subjected to separated refining in a laboratory-scale beater and in a mill-scale refiner as well. The effect of the separated refining on the refining rates and papermaking properties were evaluated. Results obtained are summarized as follows: 1. Fiber flocculation tendency of cotton staple was estimated to be significantly greater than that of linter fibers; 2. The staple fibers showed higher cellulose DP, longer fiber length and higher sheet strength at a given refining degree compared to linter fibers, but remarkably slower refining rate was observed; 3. The separated refining system exhibited a significant increase in sheet strengths, especiauy in folding endurance, with an increase in the fibrillation on the surface of staple fibers, but slightly lower or comparable fiber length after refining to the mixed refining system; 4. Similar results were also obtained from the machine trial in which about 7-8％ energy saving effects were achived in the separated refining system. On the basis of the results observed in this study, it was concluded that a significant increase in paper strength and a substantial reduction in refining energy consumption could be achieved using the separated refining system for the cotton staple and linter fiber stock refining.