• 한국소성가공학회:학술대회논문집
• /
• 한국소성가공학회 1999년도 제3회 압연심포지엄 논문집 압연기술의 미래개척 (Exploitation of Future Rolling Technologies)
• /
• pp.272-278
• /
• 1999

Tungsten Carbide(WC) Roll is widely used in finishing stands of wire rod mill. This report is about the manufacturing method of WC roll with excellent wear resistance. To enhance wear resistance, WC content has been increased to the maximum extent while binder content such as Co, Ni, Cr has been minimized. Part of WC is replaced with TiC having more wear resistant than WC. WTiC powder has been used to prevent weight unbalance resulting from the difference of specific weight when adding TiC. The roll manufactured by this method, is having more wear resistance than the existing rolls when applying to the final stand of the finishing mill. This report shows that WC is the critical factor of wear resistance in WC rolls and an approprite amount of TiC effects wear resistance and when adding TiC, using WTiC powder is better.

• 제어로봇시스템학회:학술대회논문집
• /
• 제어로봇시스템학회 2001년도 ICCAS
• /
• pp.73.3-73
• /
• 2001

Finishing mill (FM) is set up with rolling conditions (rolling speed, rolling force, roll gap, etc.) calculated by a FSU (Finisher Setup) model considering the temperature, qualities and size of a transfer bar and a strip at the entry and exit of FM before the transfer bar is rolled through FM. If the accuracy of setup is low mass flow unbalance occurs, so that the accuracies of the strip thickness and width become lower or rolling operation fault occurs. Therefore, to enhance the performance of the FSU model and to improve mass flow and the thickness accuracy of a strip in the 7-stand finishing mill using a hot strip speed measurement system. This study is being performed. In this paper, the speed measurement system, a developed neural network for predicting ...

• 소음진동
• /
• 제4권1호
• /
• pp.43-50
• /
• 1994

Chatter vibration of a rolling machine in steel plants has a significant effect on thickness quality of the products. The cause and mechanism of the mill chattering is addressed through measurement of vibration and dynamic torque. An FFT system and an FM telemetry system are employed to collect data at several locations of possible damages. The results reveal the followings as sources of the mill vibration. The first is defects in roller bearings of a work roll chock. The second is instability of an oil film bearing in a backup roll chock, which has been investigated with a theoretical model describing the phenomenon. Dynamic torque is not the direct cause of mill vibration but rather influenced by the vibration. Appropriate treatment methods are suggested to address each of the above sources.

• 한국소성가공학회:학술대회논문집
• /
• 한국소성가공학회 2004년도 제5회 압연심포지엄 신 시장 개척을 위한 압연기술
• /
• pp.175-183
• /
• 2004

In hot strip rolling, a capability for precisely predicting roll force is crucial for sound process control. In the past, on-line prediction models have been developed mostly on the basis of Orowan's theory and its variation. However, the range of process conditions in which desired prediction accuracy could be achieved was rather limited, mainly due to many simplifying assumptions inherent to Orowan's theory. As far as the prediction accuracy is concerned, a rigorously formulated finite element(FE) process model is perhaps the best choice. However, a FE process model in general requires a large CPU time, rendering itself inadequate for on-line purpose. In this report, we present a FE-based on-line prediction model applicable to precision process control in a finishing mill(FM). Described was an integrated FE process model capable of revealing the detailed aspects of the thermo-mechanical behavior of the roll-strip system. Using the FE process model, a series of process simulation was conducted to investigate the effect of diverse process variables on some selected non-dimensional parameters characterizing the thermo-mechanical behavior of the strip. Then, it was shown that an on-line model for the prediction of roll force could be derived on the basis of these parameters. The prediction accuracy of the proposed model was examined through comparison with measurements from the hot strip mill.

• 한국전자파학회논문지
• /
• 제15권3호
• /
• pp.311-318
• /
• 2004

PCM/FM과 같은 디지털 변조 방식의 텔레메트리 시스템에 있어서 비트 에러율(BER)을 최소화하여 수신된 신호의 품질을 향상시키기 위해서는 충분히 안정된 신호마진을 갖도록 회선설계가 이루어져야 한다. 특히 고속으로 이동하는 비행체의 경우에는 비행체 자세에 따른 송수신 안테나 사이의 안테나 이득패턴의 변화와 비행거리에 따른 손실이 동반되어지며 이로 인해서 회선상의 요동이 발생된다. 본 논문에서는 2002년 11월에 한국항공 우주연구원에서 시험 발사되었던 국내 최초 액체로켓 KSR-III의 비행시험 중에 S-대역 지상국에서 측정된 텔레메트리 신호의 신호대잡음비(SNR) 변화와 로켓의 비행 궤적 및 롤, 피치, 요 등의 자세변화를 고려하여 시뮬레이션으로 계산된 결과를 비교 분석하였으며 이를 통해 회선마진의 변화가 잘 일치함을 확인할 수 있었다. 또한, 탑재 안테나 개수가 1개인 경우와 롤 변화가 없는 가상의 비행 상황에 대해서 시뮬레이션을 수행하여 회선 변화를 예측할 수 있었다.

• 한국항공우주학회지
• /
• 제37권10호
• /
• pp.992-997
• /
• 2009

본 논문에서는 제한된 센서 조건에서 유도탄 동체의 각속도를 계산하는 법을 보이고 Flight Motion Simulator(FMS)를 이용한 각속도 계산식 검증을 다룬다. 일반적으로 유도탄 동체의 각속도는 동체에 탑재하는 각속도 자이로를 이용하여 측정하지만, 유도탄 동체에 탑재하는 관성 센서 중에 피치와 요 각속도 자이로가 없는 제한된 센서 조건을 가정한다. 이와 같은 제한된 센서 조건에서 김블 탐색기 자이로, 동체의 롤 각속도 자이로, 김블의 자세 측정값 및 자세 변화율을 이용하여 유도탄 동체의 각속도를 계산할 수 있음을 보인다. 제안한 각속도 계산식을 검증하기 위하여 FMS를 이용한 실험을 수행하였다.

• 제어로봇시스템학회논문지
• /
• 제15권6호
• /
• pp.634-640
• /
• 2009

The plate manufacturing processes are composed of the reheating furnace, finishing mill, cooling process and hot leveling. The finishing rolling mill (FM) as a reversing mill has produced the plate steel through multiple pass rolling. The automatic gauge control (AGC) is employed to maintain the thickness tolerance. The high grade products are forming greater parts of the manufacturing and customers are requiring strict thickness margin. For this reason, the advanced AGC method is required instead of the conventional AGC based on the PI control. To overcome the slow response performance of the conventional AGC and the thickness measurement delay, a fuzzy AGC based on the thickness deviation and its trend is proposed in this paper. An embedded controller with the fuzzy AGC has been developed and implemented at the plate mill in POSCO. The fuzzy AGC has dynamically controlled the roll gap in real time with the programmable logic controller (PLC). On line tests have been performed for the general and TMCP products. As the results, the thickness deviation range (maximum - minimum of the inner plate) is averagely from 0.3 to 0.1 mm over the full length. The fuzzy AGC has improved thickness deviation and completely satisfied customer needs.