• 전력전자학회:학술대회논문집
• /
• 전력전자학회 2000년도 전력전자학술대회 논문집
• /
• pp.343-346
• /
• 2000

In most inverter/converter applications SVPWM method is the preferred approach for it shows good characteristics in linear modulation range and waveform quality. in this paper we propose a new carrier based SVPWM method for multi-level system. First we survey the conventional carrier based SVPWM method and investigate the problem of the conventional one for the multi-level system with the focus on the switching frequency harmonic flux trajectories. Finally we propose a new carrier based SVPWM method that can reduce harmonic distortion. Simulation and experimental results are given for the verification of the proposed SVPWM method.

• 한국초전도학회:학술대회논문집
• /
• 한국초전도학회 2003년도 High Temperature Superconductivity Vol.XIII
• /
• pp.57-57
• /
• 2003

• 한국농림기상학회지
• /
• 제17권1호
• /
• pp.15-24
• /
• 2015

$CH_4$는 $CO_2$ 및 $N_2O$와 더불어 중요한 온실가스로서 지속적이고도 체계적인 감시가 요구된다. 에디 공분산 기술 기반의 $CO_2$ 플럭스의 관측은 이미 세계적으로 관측망이 구축되어 관측부터 자료처리에 이르기까지 모든 과정이 표준화되어 있을 뿐 아니라 체계적으로 잘 문서화되어 있다. 그러나 미량 기체인 $CH_4$의 경우, 레이저 기반의 고속반응 분광계를 필요로 할 뿐 아니라, 이에 수반되는 플럭스 자료의 처리 과정이 표준화되어 있지 않다. 본 연구 노트에서는 최근에 상용화된 개회로 파장 변조 분광계를 사용하여 에디 공분산 방법으로 논에서 관측한 $CH_4$ 플럭스 결과를 보고하였다. 모내기 전과 직후의 각 5일간 연속 관측한 자료를 KoFlux 프로토콜에 따라 상용화된 $EddyPro^{TM}$ 프로그램을 사용하여 자료를 처리하였다. 이 후처리 과정에서 세 가지 주요 보정, (1) 주파수 반응 보정, (2) 공기 밀도 보정, (3) 분광 보정의 효과를 정량화 하였다. 보정 효과는 밤과 낮에 따라 차이를 보였고, 메탄플럭스가 작을수록 보정 효과가 컸다. 전반적으로 보정 후에 메탄 플럭스는 평균 20-25% 정도 증가하였다. 국가농림기상센터(www.ncam.kr)에서는 분광 보정과 빈 자료 메우기를 포함한 $CH_4$플럭스 자료 처리가 포함된 업데이트된 KoFlux 프로그램을 일반 사용자에게 제공할 예정이다.

• Journal of Electrical Engineering and Technology
• /
• 제8권2호
• /
• pp.304-315
• /
• 2013

In this paper, analysis of cascaded H-bridge multilevel inverter in DTC-SVM (Direct Torque Control-Space Vector Modulation) based induction motor drive for FCEV (Fuel Cell Electric Vehicle) is presented. Cascaded H-bridge multilevel inverter uses multiple series units of H-bridge power cells to achieve medium-voltage operation and low harmonic distortion. In FCEV, a fuel cell stack is used as the major source of electric power moreover the battery and/or ultra-capacitor is used to assist the fuel cell. These sources are suitable for utilizing in cascaded H-bridge multilevel inverter. The drive control strategy is based on DTC-SVM technique. In this scheme, first, stator voltage vector is calculated and then realized by SVM method. Contribution of multilevel inverter to the DTC-SVM scheme is led to achieve high performance motor drive. Simulations are carried out in Matlab-Simulink. Five-level and nine-level inverters are applied in 3hp FCEV induction motor drive for analysis the multilevel inverter. Each H-bridge is implemented using one fuel cell and battery. Good dynamic control and low ripple in the torque and the flux as well as distortion decrease in voltage and current profiles, demonstrate the great performance of multilevel inverter in DTC-SVM induction motor drive for vehicle application.

• 제어로봇시스템학회논문지
• /
• 제21권7호
• /
• pp.662-668
• /
• 2015

This paper presents an improved predictive control of an induction machine fed by a matrix converter using N-switching vectors as the control action during a complete sampling period of the controller. The conventional model predictive control scheme based matrix converter uses a single switching vector over the same period which introduces high torque ripple. The proposed switching scheme for a matrix converter based model predictive control of an induction machine drive selects the appropriate switching vectors for control of electromagnetic torque with small variations of the stator flux. The proposed method can reduce the ripple of the electrical variables by selecting the switching state as well as the method used in the space vector modulation techniques. Simulation results are presented to verify the effectiveness of the improved predictive control strategy for induction machine fed by a matrix converter.

• Progress in Superconductivity
• /
• 제2권2호
• /
• pp.76-80
• /
• 2001

We have fabricated YBa$_2$Cu$_3$$O_{7-x}$ (YBCO) ramp-edge Josephson junctions by modifying ramp edges of the base electrodes without depositing any artificial barrier layer. YBa$_2$Cu$_3$O/7-x//SrTiO$_3$ (YBCO/STO) films were deposited on SrTiO$_3$(100) by on-axis KrF laser deposition. After patterning the bottom YBCO/STO layer, the ramp edge was cleaned by ion-beam and then reacted with deionized water under various conditions prior to the deposition of counter-electrode layers. The top YBCO/STO layer was deposited and patterned by photolithography and ion milling. We measured current-voltage (I-V) characteristics, magnetic field modulation of the critical current at 77 K. Some showed resistively shunted junction (RSJ)-type I-V characteristics, while others exhibited flux-flow behaviors, depending on the dipping time of the ramp edge in deionized water. Junctions fabricated using optimized conditions showed fairly uniform distribution of junction parameters such as I$_{c}$R$_{n}$ values, which were about 0.16 mV at 77 K with 1$\sigma$~ 24%. We made a dc SQUID with the same deionized water treated junctions, and it showed the sinusoidal modulation under applied magnetic field at 77 K. 77 K.

• Journal of Power Electronics
• /
• 제17권2호
• /
• pp.368-379
• /
• 2017

In this paper, a direct torque control algorithm with novel duty cycle-based modulation is proposed for permanent magnet synchronous motor drives fed by neutral-point clamped three-level inverters. Compared with the standard DTC, the proposed algorithm can suppress steady-state torque ripples as well as ensure neutral-point potential balance and smooth vector switching. A unified torque/flux evaluation table with multiple voltage vectors and precise control levels is established and used in this method. This table can be used to evaluate the effects of duty-cycle vectors on torque and flux directly, and the elements of the table are independent of the motor parameters. Consequently, a high number of appropriate voltage vectors and their corresponding duty cycles can be selected as candidate vectors to reduce torque ripples by looking up the table. Furthermore, small vectors are incorporated into the table to ensure the neutral-point potential balance with the numerous candidate vectors. The feasibility and effectiveness of the proposed algorithm are verified by both simulations and experiments.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 2001년도 하계학술대회 논문집 B
• /
• pp.986-988
• /
• 2001

This paper presents a digitally speed sensorless control system for induction motor with direct torque control (DTC). Some drawbacks of the classical DTC are the relatively large torque ripple in a low speed range and notable current pulsation during steady state. They are reflected speed response and increased acoustical noise. In this paper, the DTC quick response are preserved at transient state, while better qualify steady state performance is produced by space vector modulation (SVM). The system are closed loop stator flux and torque observer for wide speed range that inputs are currents and voltages sensing of motor terminal, model reference adaptive control (MRAC) with rotor flux linkages for the speed fuming signal at low speed range, two hysteresis controllers and optimal switching look-up table. Simulation results of the suggest system for the 2.2 [kW] general purposed induction motor are presented and discussed.

• 전자공학회논문지A
• /
• 제28A권9호
• /
• pp.721-728
• /
• 1991

In this paper, a magneto-optic modulator has been designed by using single crystal BSO and polycrystal ZnSe as Faraday cells. And practical core-type optical current sensors using pure iron and permalloy have been prepared and experimented. In order to obtain efficient magnetic field detection, LED(NEC OD08358, 0.87 $\mu$m) was used as optical source, PIN-PD(OD-8454)as optical receiver and multi-mode optical fiber (100/140$\mu$m) as transmission line. The characteristics matrix of the optical element was calculated by Stokes parameter, and optic modulation characteristics equations were derived by Muller matrix. Electromagnetic analysis program (FLUX 2D, micro VAX 3600) by finite element method was used to find the magnetic flux density around the core. The measuring error of the output voltage to input current has been masured below 5% in the range of 50A to 1000A. As the temperature was changed from -20$^{\circ}C$ to 60$^{\circ}C$, the maximum measurement error of the optical output has been found to be 0.5% at 60$^{\circ}C$. These experimental results show good temperature and linearity characteristics. The SNR of the overall system was 47dB in case of 600A (250.2 Oe) conductor current and the system has good noise immunity.

• 전력전자학회논문지
• /
• 제4권3호
• /
• pp.231-239
• /
• 1999

변압기로써 결합된 직렬공진 부하를 가진 전압원-인버터(Voltage-Source Inverter)가 공진주파수로 작동되는 경우에 출력 전류를 제어하는 기법으로서, 개선된 전류조절형 델타변조(Current-Regulated Delta Modulator; CRDM)방식을 제안한다. 일반적인 CRDM은, 전류편차가 상당한 크기로 나타난다는 문제가 있으며, 특히 유도가열장치와 같이 부하가 변압기를 통하여 연결되는 경우에는 변압기의 자속포화 문제가 발생하므로 실제 사용에 한계가 있다. 이러한 문제를 해결하기 위하여, 자속포화 현상을 분석하고 이를 방지하기 위한 간단한 방법을 제안하며, 전류편차를 제거하기 위한 적분형 CRDM을 적용한다. 그리고 슬라이딩 모드 제어의 개념을 이용하여, 안정된 동작을 보장하는 적분기 이득의 상한치를 회로특성치로부터 구하는 방법을 제안하고, 제안된 기법의 효용성을 시뮬레이션과 실험으로써 확인한다.