• Proceedings of the KSME Conference
• /
• 2008.11b
• /
• pp.3120-3124
• /
• 2008

A three-dimensional computational fluid dynamics (CFD) analysis is performed to investigate flow characteristics in the anode channels and manifold of the internal reforming type molten carbonate fuel cell (MCFC). Considering the computational difficulties associated with the size and geometric complexity of the MCFC system, the polyhedral meshes that can reduce mesh connectivity problems at the intersection of the channel and the manifold are adopted and chemical reactions inside the MCFC system are not included. Through this study, the gas flow rate uniformity of the anode channels is mainly analyzed to provide basic insights into improved design parameters for anode flow channel design. Results indicate that the uniformity in flow-rate is in the range of ${\pm}1%$ between the anode channels. Also, the mal-distributed inlet flow-rate conditions and the change in the size of the manifold depth have no significant effect on the flow-rate uniformity of the anode channels.

• Journal of the Korean Society for Industrial and Applied Mathematics
• /
• v.20 no.1
• /
• pp.37-50
• /
• 2016

A large eddy simulation (LES) of a turbulent channel flow is performed by using the third order low-storage Runge-Kutta method in time and second order finite difference formulation in space with staggered grid at a Reynolds number, $Re_{\tau}=590$ based on the channel half width, ${\delta}$ and wall shear velocity, $u_{\tau}$. To reduce the calculation cost of LES, algebraic wall model (AWM) is applied to approximate the near-wall region. The computation is performed in a domain of $2{\pi}{\delta}{\times}2{\delta}{\times}{\pi}{\delta}$ with $32{\times}20{\times}32$ grid points. Standard Smagorinsky model is used for subgrid-scale (SGS) modeling. Essential turbulence statistics of the flow field are computed and compared with Direct Numerical Simulation (DNS) data and LES data using no wall model. Agreements as well as discrepancies are discussed. The flow structures in the computed flow field have also been discussed and compared with LES data using no wall model.

• Journal of Advanced Marine Engineering and Technology
• /
• v.28 no.8
• /
• pp.1195-1202
• /
• 2004

In this paper an experimental study was investigated for two-phase flow distribution in compact heat exchanger header. A test section was consisted of the horizontal bottom dividing header($\phi$: 5 mm, L: 80 mm) and 10 upward circular mini channels ($\phi$: 1.5 mm, L: 850 mm) using an acrylic tube. Three different types of tube intrusion depth were tested for the mass flux and inlet mass quality ranges of 50 - 200 kg/$m^2$s and 0.1 - 0.3, respectively. Air and water were used as the test fluids. The distribution of vapor and liquid is obtained by measurement of the total mass flow rate and the calculation of the quality. Two-phase flow pattern was observed, and pressure drop of each channel was measured. By adjusting the intrusion depth of each channel an uniform liquid flow distribution through the each channel was able to solve the mal-distribution problem.

• Journal of Ship and Ocean Technology
• /
• v.9 no.4
• /
• pp.1-10
• /
• 2005

The effect of buoyancy orientation on turbulent channel flow has been investigated using DNS (direct numerical simulation). Grashof number is kept at 9.6 $\times 10^{5}$ while changing the orientation of the buoyancy vector to be parallel or perpendicular to the channel walls. Four study cases can be distinguished during this research namely; streamwise, wall-normal unstable stratification, wall-normal stable stratification and spanwise oriented buoyancy. The driving mean pressure gradient used in all cases is adjusted to keep mass flow rate constant while friction Reynolds number is around 150. At this Grashof number, the skin friction shows decrement in the unstable and stable stratification and increment in the other two cases. Analyses of the changes of flow structure for the four cases are presented highlighting on the mean quantities and second order statistics.

• Proceedings of the Korea Water Resources Association Conference
• /
• 2022.05a
• /
• pp.138-138
• /
• 2022

Understanding a stream's or river's discharge is essential for a variety of hydrological and geomorphological applications at various sizes. However, depending on the stream environment and flow conditions, it is crucial to use the appropriate techniques and instruments. This will ensure that discharge estimations are as reliable as possible. This study presents developed smart system for continuous measurement of open channel discharge and evaluate streamflow measurement over various techniques. This includes developed smart flow meter as flow point measurements, smart water level sensor (installed on Hydraulic Structure ? Weir) and current meters. Advantages and disadvantages of each equipment are presented to ensure that the most appropriate method can be selected. we found that smart water level sensor is more prominent once used during flood event as compared to smart flow meter and current meters, while current meters seems to show better accuracy once applied for open channel.

• Proceedings of the SAREK Conference
• /
• 2008.11a
• /
• pp.215-220
• /
• 2008

A microchannel PCHE is manufactured by the two technologies of micro photo-etching and diffusion bonding. In this paper, heat transfer and pressure drop characteristics by applying various configuration for the flow channel in the microchannel PCHE is experimentally investigated. The flow channel configurations are designed three types such as straight, wavy and offset strip channels. The performance experiment of each configuration is performed for Reynolds numbers in ranges of $100{\sim}700$ under various flow conditions for the hot side and the Reynolds number of cold side is fixed at 350. The inlet temperatures of the hot side and cold side are conducted as $40^{\circ}C$ and $20^{\circ}C$, respectively. The heat transfer performance of wavy channel, which was similar to that of offset strip channel, was much higher than that of straight channel. The effectiveness of wavy channel and offset strip channel was evaluated as about $0.5{\sim}0.9$. The pressure drop of wavy channel was highest among configurations and that of offset strip channel was lower than that of straight channel because the round curved surface of each strip edge was reduced the pressure loss.

• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.40 no.7
• /
• pp.435-440
• /
• 2016

Effects of the increase rate of Reynold number on near-wall turbulent structures are investigated by performing direct numerical simulations of transient turbulent channel flows. The simulations were started with the fully-developed turbulent channel flow at $Re_{\tau}=180$, then temporal accelerations were applied. During the acceleration, the Reynolds number, based on the channel width and the bulk mean velocity, increased almost linearly from 5600 to 13600. To elucidate the effects of flow acceleration rates on near-wall turbulence, a wide range of durations for acceleration were selected. Various turbulent statistics and instantaneous flow fields revealed that the rapid increase of flow rate invoked bypass-transition like phenomena in the transient flow. By contrast, the flow evolved progressively and the bypass transition did not clearly occur during mild flow acceleration. The present study suggests that the transition to the new turbulent regime in transient channel flow is mainly affected by the flow acceleration rate, not by the ratio of the final and initial Reynolds numbers.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.27 no.5
• /
• pp.657-665
• /
• 2003

Several interesting results were obtained from the flow visualization experiment in the accompanying paper, Part I. in the present study, Part II, a numerical study has been carried out to explain the detailed flow phenomena in micro-channel filling process. Hele-Shaw flow approximation was applied to the micro-channel geometry based on the small characteristic length. And surface tension effect has been introduced on the flow front as the boundary condition with the help of a dynamic contact angle concept between the melt front and the wall. A dimensional analysis for numerical results was carried out and a strong relationship between dimensionless pressure and Capillary number is obtained. The numerical analysis results are compared with the flow visualization experimental observations. And the numerical system developed in the present study seems to be able to predict the interesting micro-channel filling flow characteristics observed from experiments.

• Journal of the Korea Safety Management & Science
• /
• v.20 no.4
• /
• pp.7-13
• /
• 2018

This study investigates the enhancement of the oxygen diffusion rate in the cathode channel of a proton exchange membrane fuel cell (PEMFC) by pure oscillating flow, which is the same as the mechanism of human breathe. Three-dimensional numerical simulation, which has the full model of the fuel cell including electrochemical reaction, ion and electronic conduction, mass transfer and thermal variation and so on, is performed to show the phenomena in the channel at the case of a steady state. This model could analysis the oscillating flow as a moving mesh calculation coupled with electrochemical reaction on the catalyst layer, however, it needs a lot of calculation time for each case. The two dimensional numerical simulation has carried on for the study of oscillating flow effect in the cathode channel of PEMFC in order to reduce the calculation time. This study shows the diffusion rate of the oxygen increased and the emission rate of the water vapor increased in the channel by oscillating flow without any forced flow.

• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.24 no.11
• /
• pp.1497-1505
• /
• 2000

A numerical study is made on the ice-formation for a laminar flow in a curved channel. When the water flows through the curved channel with the walls specified below the freezing temperature, the ice layer has been formed on the curved surface, different from that of a straight channel. The fluctuation of ice layer has been predicted, considering the variation of velocity and temperature near the curved portion of channel. The study also takes into account the interaction existing between the laminar flow and the curved channel. In the solution strategy, the present study is substantially different from the existing works in that the complete set of governing equations in both the solid and liquid regions are resolved. The results from this study have been mainly presented, focusing on the variation of ice layer close to the curved portion. Numerical results have been obtained parametrically by varying the curved angle and the radius of curvature of channel, in addition to the variation of Reynolds numbers and wall temperatures of channel. The results show that the curved shape of channel has the great effect on the thickness of the solidification layer. The wave of ice layer thickness appears in the vicinity of curved portion. This behavior of ice layer has been amplified as is the increasing of curved angle and the radius of curvature of channel. In addition, the ice layer becomes thin as Reynolds numbers in increasing. And also, as the wall temperature of channel increases, the width of channel becomes to be shrunk due to the growth of ice layers in the upper and lower wall of channel.