• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2006년도 하계학술대회 논문집 Vol.7
• /
• pp.450-450
• /
• 2006

Organic light-emitting diodes (OLED) as pixels for flat panel displays are being actively pursued because of their relatively simple structure, high brightness, and self-emitting nature [1, 2]. The top-emitting diode structure is preferred because of their geometrical advantage allowing high pixel resolution [3]. To enhance the performance of TOLEDs, it is important to deposit transparent top cathode films, such as transparent conducting oxides (TCOs), which have high transparency as well as low resistance. In this work, we report on investigation of the characteristics of an indium tin oxide (ITO) cathode electrode, which was deposited on organic films by using a radio-frequency magnetron sputtering method, for use in top-emitting organic light emitting diodes (TOLED). The cathode electrode composed of a very thin layer of Mg-Ag and an overlaying ITO film. The Mg-Ag reduces the contact resistivity and plasma damage to the underlying organic layer during the ITO sputtering process. Transfer length method (TLM) patterns were defined by the standard shadow mask for measuring specific contact resistances. The spacing between the TLM pads varied from 30 to $75\;{\mu}m$. The electrical properties of ITO as a function of the deposition and annealing conditions were investigated. The surface roughness as a function of the plasma conditions was determined by Atomic Force Microscopes (AFM).

• 한국콘크리트학회:학술대회논문집
• /
• 한국콘크리트학회 2008년도 추계 학술발표회 제20권2호
• /
• pp.185-188
• /
• 2008

플랫 플레이트 시스템은 펀칭전단과 같은 구조적 취약점이 있다. 펀칭전단의 저항력은 기둥단면의 증가, 슬래브 유효춤의 증가, 콘크리트 강도의 증가, 휨철근의 증가로 증가시킬 수 있다. 그러나 전단보강체를 설치하는 방법이 경제적, 시공적, 안정적으로 가장 좋은 방법이다. 하지만 슬래브 두께가 250mm보다 작은 슬래브에서는 전단보강체의 충분한 정착길이를 확보할수 없기 때문에 충분한 정착효과를 발휘하기 힘들다. 이전 연구에서 제안된 전단보강체의 경우 상부철근과 하부철근의 사이에 설치되었기 때문에 전단철근의 항복강도에 도달하기 전에 미끄러짐 파괴가 발생하였다. 정착강도의 영향을 주는 요인으로는 유효정착길이, 콘크리트강도, 전단철근의 직경, 정착상세이다. 본 연구에서는 슬래브 두께와 콘크리트 강도를 고려하여 제안된 보강체의 강도산정시 K factor를 제안하였다. 정착길이와 콘크리트강도를 고려함으로써 두께가 얇은 플랫플레이트 슬래브내에서 전단철근에 의한 전단강도를 정확히 산정할수 있을 것으포 판단된다..

• 복식
• /
• 제63권7호
• /
• pp.79-93
• /
• 2013

In the Korean literature, records of systematic gold thread manufacturing such as gold foil(金 箔匠), gold foil bonded with fabrics(付金匠), gold foil bonded with paper materials(金箋紙匠), refining gold(鍊金匠), cutting gold(裁金匠), and making gold thread(絲金匠) can be easily found. We can infer from these literatures that the Korean people used to make gold threads. However, is not existent the gold thread making technique. Thus, a research was done using 67 pieces of gold thread artifacts used in textiles craft of Korea, China and Japan. The purpose of this research was to identify the characteristics of the Korean gold thread by studying the artifacts' form classification, gold foil, glue and the base. First, gold thread is divided into flat gold thread and wrapped gold thread. Wrapped gold thread was made in more various methods such as with a paper on the flat gold thread, metal thread and wrapped gold thread with gold foil on top. Compared to the flat gold thread, wrapped gold thread uses a thread that has a thinner and wider. Through this analysis, even making of the base of the gold threads was different according to the type. Secondly, we looked into the characteristics of materials according to form structure of the gold thread. After analysis of experiment results, we could know that to attach Korean gold thread, glue and the mixture of materials such as Red soil(朱土) was also added. The kinds of the base of gold threads were identified as paper, leather and intestines. Among those materials, for paper, Korea's Dakji, China's Sangpiji(桑皮紙) and Jukji(竹紙) and Japan's Anpiji(雁皮紙) seemed to have all been used, so because of the difference among countries, we can prove that Korea has also produced gold thread. By looking at the research, the base of gold threads and making features hugely vary according to the area.

• The International Journal of Costume Culture
• /
• 제2권2호
• /
• pp.80-96
• /
• 1999

This research focused on pattern adjustments of the stable knit garment for women. Fourteen different types of the knitted fabrics by 12 gauge, computerized flat bed machines were cut in as one half of the torso front, one half of the torso back, and one side of the sleeves for each of them. Guidelines such as the center front, the center back, the armhole, the bust-line, the waistline, the hip-line the hemline were basted on the torso patterns in the knitted fabrics. Also the grain-line, the elbow-line, and the hemline were basted on the one side of the sleeves in the same as above knitted fabrics. The torso patterns in the knitted fabrics were exhibited on the dress-forms on top of the torso patterns in Muslin, which also have the same guidelines drawn on. The distances between the guidelines on Muslin and those on the knitted fabrics for each set of the sample fabrics were measured every three days for two weeks. The fabric properties of the fourteen knitted fabrics such as fiber contents, stitch density both in the wale and course directions, weight, thickness, stretch & recovery, residual shrinkage, relaxation and drapability were laboratory tested for how these were related to finished appearance of 12 gauge, computerized flat knit garments and also in order to prove the fourteen knitted fabrics fall to a category of such as the stable knit. The results from the investigation revealed that six fabric properties such as stitch density, thickness, stretch recovery, residual shrinkage and relaxation were not so much significant factors as weight and drapability. In conclusion, fabric weight, and drapability of the fabric resulting from fiber contents were the cause of final appearance distortion of garment. When adapting patterns for stabilized, 12 gauge, computerized flat knitted fabrics, the fiber contents of the fabrics should be taken into consideration to reduce the production cost and produce better-fit garments.

• 한국항공우주학회지
• /
• 제37권6호
• /
• pp.562-570
• /
• 2009

불어내기식 극초음속 풍동을 이용하여 2차원형 돌출물 주위의 유동 및 공력가열 특성에 대한 실험적 연구를 수행하였다. 실험의 유입 유동 조건은 마하수 7, 단위 레이놀즈수 $2.0{\times}10^6/m$ 이다. 실험 조건은 길이가 다른 두 개의 평판에 세 가지 돌출물이 높이에 따라 변화되며, 실험데이터는 쉴리렌 이미지 가시화 기법과 돌출물 전면에서의 열유속 게이지를 이용한 열유속 측정을 통해 획득되었다. 또한, 본 논문에서는 경계층 천이 탐지기법과 같은 극초음속 유동 실험 기법도 함께 제시하였다. 실험 결과 돌출물 전방에 큰 박리 영역이 관찰되었으며, 박리 영역은 돌출물의 높이와 평판의 길이에 따라 민감하게 변화 하였다. 가장 큰 돌출물의 경우에서만, 돌출물 상부 측정점에서 열유속 측정치의 급격한 점프가 있는 것으로 관찰되었다. 또한 측정된 열유속은 돌출물의 높이가 크고 평판의 길이가 길수록 증가하는 경향성을 보였다.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 1992년도 하계학술대회 논문집 B
• /
• pp.928-930
• /
• 1992

The design beam energy of PLS(Pohang Accelerator Laboratory) Linac is 2Gev. The linac employs total 11 units of modulators and klystrons. The maximum peak output powers of the modulators are 200MW (400kV, 500A, 4.4$\mu$S flat-top, 800$\Omega$ load) to drive the klystrons which have the peak microwave power of 80MW. Prior to the development of the 200MW modulators, a prototype 150MW modulator has been constructed and tested. We have achieved output pulses of 350kV, 420A and 3.5$\mu$S flat-top with 840$\Omega$ water load. In this article, the test results and computer simulations of charging, De-Q'ing, and discharging are presented.

• Journal of the Korean Wood Science and Technology
• /
• 제17권1호
• /
• pp.55-68
• /
• 1989

This experiment was carried out to investigate the crack of coated Nitrocellulose Lacquer on flatand edge-grained boards of Quercus acutissima, ring-porous wood, and Betula platyphylla var. japonica, diffuse-porous wood, by variations of moisture contents at 7, 13 and 21%. Cold check system was used as an accelerating method for crack development, in which one cycle of the system consisted of 10 replications of each unit cycle, $60^{\circ}C$ for 4hr followdd by $-20^{\circ}C$ for 4hr. The analysis of Nitrocellulose Lacquer characteristics was made by means of water permeation measurement, F.T.I.R. spectroscopy, N.M.R. spectroscopy, gel permeation chromatography, gas chromatography, and D.S.C. The results obtained were as follows: 1. The number of cracks increased with the increasing moisture content of board. 2. The crack of coated film on flat-grained board was fewer in number than on edge-grained board. 3. The crack occurred in Quercus acutissima was more numerous on edge-grained board but less frequent on flat-grained board compared with that in Betula platyphylla var. japonica, respectively. 4. The cold crack vertically developed to the grain both in Quercus acutissima and Betula platyphylla var. japonica. 5. Water permeability in intermediate coated film was lower than in under and top coated film, but the difference was not confirmed between under and top coated film.

• 한국태양에너지학회 논문집
• /
• 제36권4호
• /
• pp.57-65
• /
• 2016

Domestic photovoltaic system for roof-top is installed towards the south at an angle of 20 to 35 degrees and the shape of PV array is divided into two kinds; a plane shape and a curved shape. This paper aims to understand an actual condition of PV facility and strengths and weaknesses of support structure production and installation and to consider the best PV surface shape by analyzing theoretical logics of these two surface shapes and architectural perspective-based realistic case studies. This study targeted 98 facilities including common houses, public institutions and education institutions. In common houses, all of 59 PV facilities have a plane surface. In public institutions, 7 of 15 PV facilities have a curved array surface and 8 PV facilities have a plane surface. In education institutions, also, 14 of 24 PV facilities have a plane array surface and 10 PV facilities have a curved surface. Most of 98 facilities have a flat roof supporting shape. However, it was found that the curved shape wasn't positive for PV generation due to the change of radial density and it was at least 10 % more expensive to produce its structure. Also, domestic general large single-plate PV facilities have problems of harmony with buildings and wind load. Therefore, it is considered that for fixed-type roof-top PV, a plane PV array shape is good for optimum generation and economic efficiency and a parallel array structure on the roof surface is favorable to wind load and snow load without being a hindrance to the building facade.

• 한국지하수토양환경학회지:지하수토양환경
• /
• 제8권1호
• /
• pp.75-80
• /
• 2003

해수 중에는 연안 조간대의 저서생물의 생존에 필수적인 용존산소와 영양염이 풍부하게 내포되어 있기 때문에 해수의 토양침투는 저서생물의 생존과 밀접한 관련을 맺고 있다. 그러나 유출된 기름이 조간대에 표착하게 되면 해수의 침투가 차단되어 생물에게 많은 피해를 유발시킬 것이다. 또한 유출된 기름의 토양 침투에 관한 정보는 생태계 영향을 최소화하고 처리를 위한 대책수립의 단서로서 매우 중요하다. 본 연구에서는 유출된 기름의 침투 거동을 파악하고 침투된 기름의 해수 침투 차단을 검토하는 것을 목적으로 하여 연구를 수행하였다. 점도가 낮은 원유가 C중유보다 침투 깊이가 약 2배 깊었으며, 유출된 기름의 침투 깊이는 조간대에 표착된 기름의 양에 따라 영향을 받는 것을 알 수 있었다. 그리고 표착된 기름은 첫번째 조석에서 가장 급격한 침투거동을 보였으나, 두번째 조석변동부터는 급격한 침투 변화는 나타나지 않았다. 그리고 침투한 유분의 수직적 분포로부터 기름은 토양 표층 2cm에 집중적으로 분포하는 것을 알 수 있었다. 한편 해수의 침투량은 표착유의 양에 비례적으로 감소하였으며, C중유가 원유보다 약 1.7배 정도의 해수의 토양 침투량을 감소시키는 것을 알 수 있었다. 따라서, 침투한 기름의 처리는 가능한 빠른 시간내에 수행되어야 해수의 침투를 회복시켜 연안 조간대 생태계의 피해를 최소화 시킬 수 있다고 판단된다.

• 한국측량학회:학술대회논문집
• /
• 한국측량학회 2004년도 춘계학술발표회논문집
• /
• pp.15-26
• /
• 2004

The calibration for systematic error in LiDAR is crucial for the accuracy of airborne laser scanning. The main error is the misalignment of platforms between INS(Inertial Navigation System) and Laser scanner For planimetrical calibration of LiDAR, the building is good feature which has great changes in height and continuous flat area in the top. The planimetry error(pitch, roll) is corrected by adjustment of height which is calculated from comparing ground control points(GCP) of building to laser scanning data. We can know scale correction of laser range by the comparison of LiDAR data and GCP is arranged at the end of scan angle where maximize the height error. The area for scale calibration have to be large flat and have almost same elevation. At 1000m for average flying height, The Accuracy of laser scanning data using LiDAR is within 110cm in height and ${\pm}$50cm in planmetry so we can use laser scanning data for generating 3D terrain surface, expecically digital surface model(DSM) which is difficult to measure by aerial photogrammetry in forest, coast, urban area of high buildings