• Journal of the Korean Magnetics Society
• /
• v.11 no.2
• /
• pp.78-83
• /
• 2001

The thermal characteristics of TMR devices by using Fast Linear Annealing method has been studied. A computer program that employs the finite differential method has been developed to simulate the temperature distribution of a diameter of 4" silicon wafer, which is subjected to radiation heat from the halogen lamp. We adopted the temperature of 350$\^{C}$, which is the highest temperature usually used in annealing for magnetic thin films. We changed moving velocity of the lamp from 0.05 mm/sec to 1 mm/sec. The moving velocity of halogen lamp has less effect on the local peak temperature of the sample only about 40$\^{C}$. Therefore, we may be able to anneal TMR devices in such short time of 1 minute and 40 seconds per one wafer, using the Fast Linear Annealing method.

• Tunnel and Underground Space
• /
• v.14 no.5
• /
• pp.327-338
• /
• 2004

The purpose of this research is to establish a concept of the factor of safety of tunnels which is a quantitative estimate of the stability of tunnels. Based on this concept, a numerical technique which calculates the factor of safety of tunnels was developed. To obtain the safety factor of a tunnel, the strength reduction technique in which a series of analyses are repeated with reduced ground strength until the tunnel collapses were employed. With this technique, the failure plane, as well as the factor of safety, can be obtained without prescribing the trial failure plane. Analyses were conducted with FLA $C^{2D}$(ver3.3), a geotechnical analysis program which is based on the finite difference method. From the result, the location of plastic zones, the maximum convergence and the maximum stress generated in the support system were also analyzed. The result shows that factors of safety are higher for the 1st and 2nd rock classes, and lower for the lower rock classes. Furthermore, factor of safety is higher when $K_{0}$ =0.5 compared to at in case of $K_{0}$ =2.0. Through this research, it is found that the factor of safety defined in this research can be used as a good quantitative index representing the stability of tunnels. Also, close examination of the results can help adjustment of the quantity and location of additional supports.s.

• KOREAN JOURNAL OF CROP SCIENCE
• /
• v.34 no.2
• /
• pp.142-146
• /
• 1989

Anther and/or tissue culture of cross pollinated crops would be very important because it can result in the direct use of haploids or doubled haploids for developing superior hybrids or varieties. The objective of the study was to investigate the response frequencies in anther and/or tissue-cultured hybrids of corn. pearl millet and buckwheat to identify agronomically acceptable germplasm of the crops. 27 crosses of corn inbred lines were evaluated by plating their anthers on N6. MS and Yu-Pei media. Two genotypes of FR1l41/FR16 hybrid cultured on N6 medium and Fla 2BT73/S6013 hybrid cultured on N6 medium responded with one anther producing calli when plated after 5$^{\circ}C$ low temperature treatment for one week. Immature embryos of corn hybrid Suwon 19 responded producing calli that were regenerated to plants at a 8.6 percent success rate. Of the 20 corn hybrids. immature tessels of FR1l41/FR16. B68/A1l6N//KS15. KS16/KS17. GA209/DB578 and SDB126/GA209 crosses responded at a relatively higher success rate producing calli that were regenerated to plants. In tissue culture of elongating culms of pearl millet x Napier grass interspecific hybrid. 2.5-4.0mm long pieces of the culm were good for callus induction resulting in higher success rate. The epicotyl of buckwheat was very good for tissue culture. and the node produced the plants regenerated directly without callus induction on the B5 medium containing I ppm BA and 0.05 ppm IBA. There were great differences in response to anther and/or tissue culture of corn, pearl millet and buckwheat due to genotype x medium and environment interactions.

• Korean Journal of Veterinary Research
• /
• v.54 no.2
• /
• pp.91-99
• /
• 2014

An antimicrobial susceptibility test was conducted to compare the resistance rates among Campylobacter spp. isolates from dogs (n = 50) raised under diverse conditions and humans (n = 50). More than 60% of Campylobacter (C.) jejuni from dogs and humans showed resistance to nalidixic acid, enrofloxacin and ciprofloxacin. C. jejuni isolates from humans showed higher resistance to tetracycline (83.3%) and ampicillin (91.3%) than those from dogs. None of the C. jejuni or Campylobacter coli isolates from humans or dogs were resistant to erythromycin. Overall, 85% of Campylobacter spp. isolates showed a multidrug resistant phenotype. Nucleotide sequencing analysis of the gryA gene showed that 100% of $NA^R/CIP^R$ C. jejuni isolates from dogs and humans had the Thr-$86^{th}$-Ile mutation, which is associated with fluoroquinolone resistance. flaA PCR restriction fragment length polymorphism (RFLP) typing to differentiate the isolates below the species level revealed 12 different clusters out of 73 strains. The human isolates belonged to eight different RFLP clusters, while five clusters contained dog and human isolates.

• Parasites, Hosts and Diseases
• /
• v.57 no.4
• /
• pp.341-357
• /
• 2019

Acanthamoeba, one of free-living amoebae (FLA), remains a high risk of direct contact with this protozoan parasite which is ubiquitous in nature and man-made environment. This pathogenic FLA can cause sight-threatening amoebic keratitis (AK) and fatal granulomatous amoebic encephalitis (GAE) though these cases may not commonly be reported in our clinical settings. Acanthamoeba has been detected from different environmental sources namely; soil, water, hotspring, swimming pool, air-conditioner, or contact lens storage cases. The identification of Acanthamoeba is based on morphological appearance and molecular techniques using PCR and DNA sequencing for clinico-epidemiological purposes. Recent treatments have long been ineffective against Acanthamoeba cyst, novel anti-Acanthamoeba agents have therefore been extensively investigated. There are efforts to utilize synthetic chemicals, lead compounds from medicinal plant extracts, and animal products to combat Acanthamoeba infection. Applied nanotechnology, an advanced technology, has shown to enhance the anti-Acanthamoeba activity in the encapsulated nanoparticles leading to new therapeutic options. This review attempts to provide an overview of the available data and studies on the occurrence of pathogenic Acanthamoeba among the Association of Southeast Asian Nations (ASEAN) members with the aim of identifying some potential contributing factors such as distribution, demographic profile of the patients, possible source of the parasite, mode of transmission and treatment. Further, this review attempts to provide future direction for prevention and control of the Acanthamoeba infection.

• Journal of Korean Society of Environmental Engineers
• /
• v.34 no.8
• /
• pp.574-582
• /
• 2012

This study presents the concentrations of the polycyclic aromatic hydrocarbons (PAHs) listed as priority pollutants by United States Environmental Protection Agency (US EPA), in 98 sludges from 54 industrial wastewater treatment facilities of South Korea. The mean concentrations of ${\Sigma}_{16}PAHs$ were ranged from 32.5 ${\mu}g/kg-dw$ to 1189.3 ${\mu}g/kg-dw$ by industries, and the highest content was found in the petrochemical industry, followed by chemical, clothing manufacturing and dying, pulp and papermaking, secondary wastewater treatment, and food/beverage producing industries. Comparisons to the EU and Danish standards of ${\Sigma}_{16}PAHs$ in sewage sludge for land application showed only two samples (one from petrochemical, and the other from chemical industry) exceeded the limits. ANOVA test with PAH concentrations as variables revealed no statistically significant influences by industrial types and sampling time (i.e., seasonal variations). Pearson correlations between individual PAHs showed strong relationships (r>0.7) among 4-ring PAHs. Concentrations of acenaphthylene, anthracene, fluoranthene, benzo(a)anthracene, benzo(f)fluoranthene, benzo(k)fluoranthene, benzo(a)pyrene presented strong correlations to ${\Sigma}_{16}PAHs$. Principal component analysis discriminated entire samples into three groups by two principal components (PC1 and PC2) with 70% of data variations, in which industrial types were not of importance, but a dominance of certain PAHs. Samples in group-I, which is high PC1 and low PC2, were characterized by a dominance of 2-ring PAHs, and in group-II, PC1 and PC2 showed a linear relation, was dominant 4-ring PAHs. Group-III with low PC1 and high PC2 includes 17 samples showing a noticeably high contribution of 3-ring PAHs to ${\Sigma}_{16}PAHs$. This study provides concentrations of PAHs in industrial sludges collected from a wide variety of sources (six industrial types) and two seasons of sampling events, and the comparison of ${\Sigma}_{16}PAHs$ with other studies are also discussed.

• Korean Journal of Veterinary Service
• /
• v.37 no.2
• /
• pp.85-96
• /
• 2014

Total 99 strains of Campylobacter spp. were isolated from 117 cases of duck's fecal samples. Among 99 strains of Campylobacter spp. isolates, 93 strains (93.9%) were C. jejuni and 6 strains (6.1%) were C. coli. Prevalence of virulence and GBS associated genes of 72 C. jejuni isolates was determined by m-PCR. Among the 10 kinds of virulence associated genes, cadF, dnaJ, flaA and ceuE genes were detected in all of C. jejuni isolates from ducks, racR, pldA, iamA, ciaB, virB11 and docC genes were 87.5%, 84.7%, 77.8%, 48.6%, 13.9% and 11.1%, respectively. Antimicrobial susceptibility test was performed on 72 C. jejuni isolates. The rate of resistance were 62.5% for oxytetracycline, 55.6% for kanamycin, 54.2% for enrofloxacin, 50% for ciprofloxacin, 37.5% for tetracycline and nalidixic acid, 18.1% for ampicillin, 15.3% for streptomycin, and 6.9% for ofloxacin. All isolates were susceptible to erythromycin. The adherence (intracellular and extracellular bacteria) abilities of the 20 isolates to INT-407 cells were between $4.21{\pm}1.27{\times}10^4$ CFU/well and $1.053{\pm}0.451{\times}10^6$ CFU/well from the isolates of cj-55 and cj-52, respectively, and that can be expressed as 0.1033% to 5.2655% to the infecting inoculum. The invasion (intracellular bacteria) abilities of the 20 isolates to INT-407 were between $1.00{\pm}1.73{\times}10^3$ CFU/well and $8.47{\pm}5.16{\times}10^4$ CFU/well from the isolates of cj-13 and cj-47, respectively, and that can be expressed as 0.0050% to 0.4235% to the infecting inoculums. The average CFU/well of 20 campylobacters isolated from ducks for adherence to and invasion were $2.646{\pm}2.886{\times}10^5$ and $3.03{\pm}2.7{\times}10^4$ respectively, and that was $1.3230{\pm}1.2139%$ and $0.1516{\pm}0.1343%$ of the starting viable inoculum. There was considerable correlation ($R^2$=0.627) between the adherence and invasion ability of C. jejuni isolates for INT-407 cell.

• Tunnel and Underground Space
• /
• v.10 no.3
• /
• pp.344-354
• /
• 2000

The concrete plug in an underground cavern prevents the stored product (oil, gas, etc) from leaking and the excessive inflow of underground water, so it plays an important role in construction and operation of the storage cavern. Additionally, it should maintain its stability under every possible loading condition. Once the plug is constructed, the cavern is isolated from the external access. Therefore, mechanical and hydraulic consideration should be made in construction to fulfill its function. Therefore, in this study, numerical analyses were conducted to study the optimal shape and thickness of the plug with respect to the various conditions of installation depth, the shape of the plug, in-situ stress ratio (K), the condition of rock-plug interface, and the effect of Excavation Damaged Zone (EDZ). This paper also presents the effect of slot depth on the hydraulic behavior of the plug. These analyses were carried out by using the 2-dimensional finite difference code, rm FLAC, and the 3D code, rm FLAC$\^$3D/.

• Food Industry
• /
• s.94
• /
• pp.37-40
• /
• 1988

1) 본 연구에서 시료로 선정한 충남 서산산 건강(dry ginger)은 수분이 $9.4\%$, 회분이 $8.7\%$ 그리고 alcohol에 의한 추출량이 약 $9\%$이다. 이는 선진국에 채택사용하고 있는 건강의 규격기준에 의하면 양호하다. 2) Non- flavor물질의 추출을 최소화하고 특히 증류과정에서 유효성분 손실을 최소화 할 수 있고, 엑기스내의 용매 잔류량이 인체에 유해하지 않고 추출효율을 높일 수 있는 용매는 ethyl alcohol이다. 3) 널리 사용하고 있는 관류추출(percolation)의 성능을 분석하고 이의 개선방안을제시하였다. - 추출효율을 높이기 위하여 건강(dry ginger)의 입자를 작게하면 압력강하가 증대되어순환되는 용액의 유속을 제어하기가 힘들다. - 입자가 작을 시에는 유체의 흐름이chan-nelling현상을 나타낸다. - 위와 같은 조건에서는 물질 전달속도가 느리므로 추출효율을 증대시킬 수가 없다. - 따라서 percolation추출에 사용되는 건강의 입자크기는 30mesh크기 이상이어야 운전조작이 용이하나 추출효율이 낮으므로, 추출시간 6시간에 회수된 생강엑기스양은 약 $2.5\%$이다. 4) percolation추출의 단점을 보완하기 위하여 기계적교반 추출을 선택하여 다음과 같은 개선점을 찾았다. - 교반형 추출에서는 고 - 액분리시 cake 저항에서 문제가 야기되지 않는 범위까지 건강의 입자를 작게할 수 있으므로 추출효율을 크게 향상시킬 수 있었다. 즉, 작게 분쇄된 건강(30mesh통과$90\%$)을 대상으로 추출시간 3시간에 $7\%$의 회수율로 증대시켰다. 최적 운전조건은 다음과 같다. 건강시료:1kg 시료크기:-30mesh$90\%$ 용매:ethyl alcohol 3$\iota$ 교반속도:900r.p.m 추출온도:상온($15\~25^{\circ}C$) 추출시간:3시간 일차 추출조건과 동일하게 하여 얻어진 엑기스의 수율이 $2\~2.5\%$이므로 총엑기스의 수율은 건강(dry ginger)무게기준으로 $8.5\~9.5\%$이었다. 5) 교반추출의 효율이 개선되었다 하더라도 추출물의 분리가 용이하여야만 공정의 이용이 가능하다. 그러므로 교반추출후 고 - 액분리를 위하여 정압여과 장치를 이용하여 여과시 cake의 평균 비저항을 얻었으며, 이의 값은 $4.31\times10^8cm\;/\;gr$으로서 여과에는 어려움이 없다는 것을 의미한다. 따라서 추출속도와 효율이 상대적으로 우수한 교반형 추출기의 가능성을 예시할 수 있음을 알 수 있었다. 6) 추출물을 농축과정에서 휘발성 oil의 손실을 최대로 줄이기 위해서는 단순증류를 하지 말고 분별증류를 수행하여야 하며, gingerol과 같은 중요성분의 열분해 반응을 억제하기 위해서는 열전달 효율을 증대시켜 증류조작을 원활히 수행하여야 하므로, still내의 농축물을 계속 교반시켜야 하며 감압상태에서 증류온도는 $40\~50^{\circ}C$로 유지시키는 것이 가장 바람직하다. 7) Ethyl alcohol로 추출된 엑기스내의 수분이나 회분함량은 외국산 제품에 비하여 약간 낮고, 반면에 조지방 및 조단백 성분의 함량은 약간 높게 나타나고 있어 대체적으로 본 연구에서 얻어진 엑기스내의 비풍미성분(non- fla-vour component) 함량은 외국산에 비하여 많은 차이가 없다. 8) 수입 외국산에 비하여 국산엑기스(본 연구에서 ethyl alcohol로 추출)내의 무기성분등의 함량은 비교적 낮은 편이다. 9) 건강에서부터 oleoresin을 얻어 paradol을 제거시킨 후 순수한 gingerol을 분리하여 IR과 NMR로 확인한 결과, 국산건강의 엑기스에는 주로 6-gingerol이고 약간의 10-gingerol이 함유된 것으로 나타났다. 10) 순수하게 분리된 gingerol을 열분석(TGA와 DTG)한 결과 약 $75^{\circ}C$에서 gingerol의 열분해 반응이 일어남을 알수 있었다. 11) 건강 분말시료와 엑기스내의 미생물 검사 결과 건강분말에서는 세균수가 많이 존재하는 것으로 나타났으나, 이는 ethyl alcohol로 추출하는 공정 중 대부분의 균들이 사멸된 것으로 나타났다. 12) 관능적 측면에선, 본 연구에서 제조한 엑기스와 수입엑기스를 비교한 결과 생강 특유의 맛은 비슷했으나, 수입엑기스에서는 쓴맛과 톱밥냄새를 느낀다는 결과를 나타내었으며 전체적인 종합적 풍미는 국산 건강엑기스가 좋은 것으로 나타났다.

• Applied Biological Chemistry
• /
• v.44 no.3
• /
• pp.143-147
• /
• 2001

An osmometrical method for determination of the degree of hydrolysis (DH) of hemoglobin was comparatively examined through TNBS (trinitrobenzene) sulfonic acid) method using two experimental variables $({\alpha}\;and\;{\beta})$, which were chosen based on correlation curves between hydrolysis equivalents (h) and $leucine-NH_2$ equivalents. DH values measured through osmometry and TNBS method highly correlated with $R^2$ values of $0.974{\sim}0.991$, irrespective of the reaction pHs and types of enzyme used. $DH_{osm}/DH_{TNBS}$ was >$1.438{\sim}1.656$ depending on the hydrolysis pH $7.5{\sim}10.0)$. Correlation euqations were well fit for measuring DH of Hb hydrolysate at different pH conditions. $DH_{osm}/DH_{TNBS}$ for co-treatment system using Esperase and Flavourzyme was 1.658, in good agreement with that of 1.656 for the single enzyme (Esperase) system. Thus, the osmometrical method was suggested to be a convenient, reliable, and rapid method for determination of DH of hemoglobin hydrolysates.