• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2009.11a
• /
• pp.264-264
• /
• 2009

The sensitivity lighting of pendant type used Micro-controller AVR, embodiment method for Munsell chromaticity diagram system and adoption method for light source lens respectively. About a plan design of light fixture, LED circuit designed flow chart of circuits and LED driver of organizations in electron device. For used Solidworks soft ware program, LED light source must take a heat shink part and LED light fixture module for sensitivity lighting of pendant type into considerations

• Journal of the Korean Institute of Illuminating and Electrical Installation Engineers
• /
• v.25 no.4
• /
• pp.24-29
• /
• 2011

When an emergency light turns on due to a blackout, the intensity of illumination is drastically changed from hundreds [1x] to 1.0[1x]. This sharp change of illumination intensity not only lowers the darkness adaptation of the eye, it also degrades the obstacle cognitive ability of the evacuees, resulting in secondary critical accidents due to anxiety, and fear. Thus, this study proposed a convertible emergency lighting fixture that controls the rate of speed of light in two stages by time with darkness adaptation of the eye in consideration. In addition, the effect of such emergency light is verified by suggesting an illumination simulation without increasing the number of light or capacity of battery to make it economically feasible.

• Proceedings of the KIEE Conference
• /
• 2003.04a
• /
• pp.104-106
• /
• 2003

In this paper, we study about the stator winding magnetization method and the magnetizing fixture magnetization method in post-assembly magnetization. Most of small electrical machine use the stator winding magnetization method but it is impossible to magnetize the permanent magnet by the stator winding magnetization method when the capacity of machine increases and the coercive force of magnet increases. And the eddy current disturbs the magnetization seriously in case of LSPM(Line Start Permanent magnet Motor) that have conductor bar in rotor. Hence, the magnetization fixture is required. So, in this paper we study about the post-assembly magnetization method that can use the stator winding magnetization method or must use the magnetization fixture magnetization method.

• Proceedings of the KIEE Conference
• /
• 2003.10a
• /
• pp.53-56
• /
• 2003

Photometric analysis is essential process to make design for 300W Electrodeless flood lighting fixture. But lighting source's unusual shape makes it difficult to fix in and so we supposed two kinds of installation method to solve this matter. One is to place lamp base down and second is to put lamp base side like normal HID lamps. In result, former photometric analysis came to reach a target for similar asymmetric photometric data meanwhile we can not escape work to design complicated reflector. Second analysis reached conclusion that it is more simplified reflector than former. On its lighting fixture's design, the former reflector is new and attractive breaking fixed idea but the latter is only staying in the range of existing HID lighting design.

• Journal of KSNVE
• /
• v.5 no.4
• /
• pp.555-563
• /
• 1995

This paper proposes the method of antiresonance frequency analysis of multi-input multi-output system. The structural dynamic modification techniques by antiresonance frequency analysis are also applied to reduce the undertest at specimen attachment points on the fixture in environmental vibration test, which is resulted from the inconsistency of antiresonance frequencies at any specified points. Several computer simulations show that the proposed method can remove the undertest problem which is not removed in conventional vibration test control. And the effectiveness of the method is verified with the impact hammer excitation of aluminium fixture model.

• Journal of the Korean Society of Manufacturing Process Engineers
• /
• v.14 no.1
• /
• pp.51-56
• /
• 2015

This paper presents an investigation of abnormal wear of a contact jig between a nail and a nail fixture in electric resistance welding. To perform an analysis on the abnormal wear phenomenon, several methods are provided. Based on the theory of electric resistance welding, are analyzed. Using microscopic analysis, surface craters are observed. In the measurement of the electric current flow in the nail fixture, the current flow distribution is measured. From several analyses, the cause of abnormal wear in the contact jig is measured using the electric discharge of high current density at the inflow point of the electric supply to the nail fixture. An alternative shape for normal wear is proposed.

• Proceedings of the Korean Society For Composite Materials Conference
• /
• 2002.10a
• /
• pp.96-99
• /
• 2002

In order to determine the in-plane shear properties of unidirectional carbon fiber reinforced aluminum laminate composites, a new Iosipescu shear test fixture was developed, by using a fixture undergoing tensile force for the specimen edge to be subjected to compressive loads assumption, under plane stress. Also, to compare the results, Iosipescu shear test method by the modified Wyoming fixture and the off-axis tensile test were performed to determine the shear properties. Off-axis tension test was performed by using new oblique-shaped tabs proposed by Sun and Chung. [5] The oblique tabs reduced remarkably end-constraint effects of off-axis specimens with a aspect ratio of about eight. It is observed through the experimental results show that there is no significant difference between off-axis test results and those of Iosipescu shear test.

• Journal of the Korean Society of Manufacturing Process Engineers
• /
• v.13 no.3
• /
• pp.89-95
• /
• 2014

The increasing level of demand for multi-tasking machines requires a saddle with an ultra-precise machining accuracy level of $15{\mu}m$, as such a saddle is one of the main components of these machines. The manner of achieving ultra-precise machining accuracy mainly depends on the fixed forces. In this paper, we optimized the number of contact points and the contact positions to reduce the deformation of the saddle while it is machined. The performance levels of the proposed optimal jig and fixture are determined by measuring the flatness, parallelism and perpendicularity of a machined saddle. The machining accuracy is found to be lower than $15{\mu}m$ at all measured points.

• Journal of the Korean Society of Propulsion Engineers
• /
• v.1 no.2
• /
• pp.48-57
• /
• 1997

The method of antiresonance frequency analysis of multi-input system is proposed. The structural dynamic modification using antiresonance frequency analysis is also applied to reduce the undertest at specimen attachment points on the fixture in environmental vibration test, which is resulted from the inconsistency of antiresonance frequencies. Several computer simulations show that the proposed method can remove the undertest problem which is not removed in conventional vibration test control. And the effectiveness of the method is verified with the impact hammer excitation of aluminium fixture model.

• Korean Journal of Air-Conditioning and Refrigeration Engineering
• /
• v.26 no.1
• /
• pp.38-41
• /
• 2014

Fixture units and the diversity curve are used, in order to determine the required size of water supply pipe. However, the values of the National Plumbing Code, International Plumbing Code and National Standard Plumbing Code of America are not the same. The objective of this study is to comparatively analyze the fixture units and the peak flows of a 10th story office building, at any instant of time, according to the three codes.