• 대한설비공학회:학술대회논문집
• /
• 대한설비공학회 2008년도 하계학술발표대회 논문집
• /
• pp.1195-1200
• /
• 2008

This study have goal with conceptual design for Offshore Structures of high pressure control valve for localization. Ball valve for development accomplished with flow analysis based on provision of ANSI B16.34, ANSI B16.10, ANSI B16.25 In order to localize the Offshore Structures high pressure control valve. Numerical simulation using CFD(Computational Fluid Dynamic) in order to predict a mass flow rate and a flow coefficient form flow dynamic point of view. The working fluid assumed the glycerin($C_3H_8O_3$). The valve inlet and outlet setup a pressure boundary condition. The outlet pressure was fixed by atmospheric pressure and calculated until increasing 1bar to 10bar. CFD analysis used STAR-CCM+ which is commercial code and Governing equations were calculated by moving mesh which is rotated 90 degrees when ball valve operated opening and closing in 1 degree interval. The result shows change of mass flow rate according to opening and closing angle of valve. Flow decrease observed open valve that equal percentage flow paten which is general inclination of ball valve. Relation with flow and flow coefficient can not be proportional according to inlet pressure when compare with mass flow rate. Because flow coefficient have influence in flow and pressure difference. Namely, flow can be change even if it has same Cv value. The structural analysis used ANSYS which is a commercial code. Stress analysis result of internal pressure in valve showed lower than yield strength. This is expect to need more detail design and verification for stem and seat structure.

• 대한전자공학회:학술대회논문집
• /
• 대한전자공학회 2003년도 통신소사이어티 추계학술대회논문집
• /
• pp.168-171
• /
• 2003

IEEE 802.16 Wireless MAN standard specifies the air interface of fixed point-to-multipoint broadband wireless access systems providing multiple services. Among the service classes supported by the wireless MAN, the best effort service class is ranked on the lowest position in priority and is assisted by a MAC scheme based on reservation ALOHL Such MAC scheme must include a number of components, while many of them are not specified in the standard. In this paper, we thus reveal main components of a MAC scheme supporting the best effort service and present candidate schemes implementing such components. Combining schemes for implementing components, we then construct distinctive MAC schemes supporting best effort service. In designing a MAC scheme, the delay performance induced by the scheme should be considered since scarce resource may be available for the best effort service after the preemptive resource occupation by other service classes. In this paper, we focus on the delay fairness among the subscriber stations using the best effort service. For evaluating a MAC scheme in delay fairness, we present two definitions of delay fairness and provide a criterion for optimal MAC scheme according to each definition of delay fairness. Using a simulation method we investigate the mean delay performance exhibited by each MAC scheme arid find an optimal scheme in delay fairness. From numerical examples, we observe that SR/ED/PG＋P scheme has strong delay fairness compared with MR/ED/PG＋P and SR/ED/PG＋D schemes according to a definition of delay fairness. However, other schemes are rather shown to have better delay fairness when the other definition is adopted.

• 대한설비공학회:학술대회논문집
• /
• 대한설비공학회 2008년도 동계학술발표대회 논문집
• /
• pp.357-362
• /
• 2008

This study have goal with reverse engineering for petrochemistry of high pressure ball valve for localization. Ball valve for development accomplished with flow analysis based on provision of ANSI B16.34, ANSI B16.10, ANSI B16.25 In order to localize the petrochemistry high pressure control valve. Numerical simulation using CFD(Computational Fluid Dynamic) in order to predict a mass flow rate and a flow coefficient form flow dynamic point of view. The working fluid assumed the water($H_2O$). The valve inlet and outlet setup a pressure boundary condition. The outlet pressure was fixed by atmospheric pressure and calculated inlet velocity 5m/s. CFD solver used STAR-CCM+ which is commercial code. The result shows change of mass flow rate according to opening and closing angle of valve. Flow decrease observed open valve that equal percentage flow paten which is general inclination of ball valve. The structural analysis used ANSYS which is a commercial code. Stress analysis result of internal pressure in valve showed lower than yield strength. This is expect to need more detail design and verification for stem and seat structure.

• Journal of Power Electronics
• /
• 제15권1호
• /
• pp.190-201
• /
• 2015

This paper uses the switching function approach to present a simple state model of the Vienna-type rectifier. The approach introduces the relationship between the DC-link neutral point voltage and the AC side phase currents. A novel direct power control (DPC) strategy, which is based on the sliding mode control (SMC) for Vienna I rectifiers, is developed using the proposed power model in the stationary ${\alpha}-{\beta}$ reference frames. The SMC-based DPC methodology directly regulates instantaneous active and reactive powers without transforming to a synchronous rotating coordinate reference frame or a tracking phase angle of grid voltage. Moreover, the required rectifier control voltages are directly calculated by utilizing the non-linear SMC scheme. Theoretically, active and reactive power flows are controlled without ripple or cross coupling. Furthermore, the fixed-switching frequency is obtained by employing the simplified space vector modulation (SVM). SVM solves the complicated designing problem of the AC harmonic filter. The simplified SVM is based on the simplification of the space vector diagram of a three-level converter into that of a two-level converter. The dwelling time calculation and switching sequence selection are easily implemented like those in the conventional two-level rectifier. Replacing the current control loops with power control loops simplifies the system design and enhances the transient performance. The simulation models in MATLAB/Simulink and the digital signal processor-controlled 1.5 kW Vienna-type rectifier are used to verify the fast responses and robustness of the proposed control scheme.

• Journal of Electrical Engineering and Technology
• /
• 제5권1호
• /
• pp.116-128
• /
• 2010

Modeling of the three phase electric arc furnace and its voltage flicker mitigation are the purposes of this paper. For modeling of the electric arc furnace, at first, the arc is modeled by using current-voltage characteristic of a real arc. Then, the arc random characteristic has been taken into account by modulating the ac voltage via a band limited white noise. The electric arc furnace compensation with static VAr compensator, Thyristor Controlled Reactor combined with a Fixed Capacitor bank (TCR/FC), is discussed for closed loop control of the compensator. Instantaneous flicker sensation curves, before and after accomplishing compensation, are measured based on IEC standard. A new method for controlling TCR/FC compensator is proposed. This method is based on applying a predictive approach with closed loop control of the TCR/FC. In this method, by using the previous samples of the load reactive power, the future values of the load reactive power are predicted in order to consider the time delay in the compensator control. Also, in closed loop control, two different approaches are considered. The former is based on voltage regulation at the point of common coupling (PCC) and the later is based on enhancement of power factor at PCC. Finally, in order to show the effectiveness of the proposed methodology, the simulation results are provided.

• 전기학회논문지
• /
• 제66권12호
• /
• pp.1759-1771
• /
• 2017

In this paper, an improved continuous integral variable structure systems(ICIVSS) with the prescribed control performance is designed for simple regulation controls of uncertain general linear systems. An integral sliding surface with an integral state having a special initial condition is adopted for removing the reaching phase and predetermining the ideal sliding trajectory from a given initial state to the origin in the state space. The ideal sliding dynamics of the integral sliding surface is analytically obtained and the solution of the ideal sliding dynamics can predetermine the ideal sliding trajectory(integral sliding surface) from the given initial state to the origin. Provided that the value of the integral sliding surface is bounded by certain value by means of the continuous input, the norm of the state error to the ideal sliding trajectory is analyzed and obtained in Theorem 1. A corresponding discontinuous control input with the exponential stability is proposed to generate the perfect sliding mode on the every point of the pre-selected sliding surface. For practical applications, the discontinuity of the VSS control input is approximated to be continuous based on the proposed modified fixed boundary layer method. The bounded stability by the continuous input is investigated in Theorem 3. With combining the results of Theorem 1 and Theorem 3, as the prescribed control performance, the pre specification on the error to the ideal sliding trajectory is possible by means of the boundary layer continuous input with the integral sliding surface. The suggested algorithm with the continuous input can provide the effective method to increase the control accuracy within the boundary layer by means of the increase of the $G_1$ gain. Through an illustrative design example and simulation study, the usefulness of the main results is verified.

• 한국조경학회지
• /
• 제26권3호
• /
• pp.78-78
• /
• 1998

The purpose of this research is to develop a CAD-based program for data analysis of digital elevation model(DEM) on the aspect of landscape assessment. When handling DEM data as a visual simulation of topographic landscape, it is basic interest to analyze visible area and visualize visual sensitivity distributions. In reference with landscape assessment, more intuitive and interactive visualizing tools are needed, specially in area of visual approach. For adaptability to landscape assessment, algorithmic approaches to visibility analysis and concepts for visual sensitivity calculation in this study were based on processing techniques of entity data control functions used in AutoCAD drawing database. Also, for the purpose of quantitative analysis, grid-type 3DFACE entities were adopted as mesh unit of DEM structure. Developed programs are composed of main part named VSI written in AutoLISP and two of interface modules written in dialog control language(DCL0 for user-oriented interactive usage. Definitions of camera points(view points) and target points(or observed area) are available alternatively in combined methods of representing scenic landscape, scenery, and sequential landscape. In the case of scene landscape(single camera to fixed target point), only visibility analysis in available. And total visibility, frequency of cumulative visibility, and visual sensitivity analysis are available in other cases. Visual sensitivity was thought as view angle(3 dimensional observed visual area) and the strengths were classified in user defined level referring to statistical characteristics of distribution. Visibility analysis routine of the VSI was proved to be more effective in the accuracy and time comparing with similar modules of existing AutoCAD third utility.

• 정보처리학회논문지A
• /
• 제13A권4호
• /
• pp.289-294
• /
• 2006

검사점 기법은 시스템이 장애를 내재한 경우에 효과적으로 프로세스가 장애 지점으로부터 다시 시작 할 수 있게 하는 결함 허용 방법이다. 특히, 페이지 단위 점진적 검사점 기법은 검사점 사이에서 변경된 페이지 데이터만을 저장함으로써 검사정 기록 오버헤드를 감소시킨다. 이 기법은 매 검사점 사이에서 변화하는 데이터의 크기가 가변적이므로 검사점 수행 시간도 매번 변하는 성질을 갖고 있다. 기존의 연구로 고정적인 검사점 수행 시간을 갖는 경우에 대한 효율적인 검사점 작성 시점 결정 방법이 제시된 바 있다. 그러나 매 검사점 마다 가변적인 시간을 필요로 하는 페이지 단위 점진적 검사점 기법에 대한 효율적인 작성 시점 결정 방법은 아직 연구되지 않은 분야이다. 본 논문에서는 효율적이고 적응성 있는 검사점 작성 시점 결정 방법을 제안하고, 이 방법에 기반을 둔 적응성 있는 페이지 단위 점진적 검사점 기법을 보인다. 여러 가지 용용 프로그램의 실험 결과를 통하여, 제안한 방법을 사용하는 것이 기존의 고정적인 인터벌을 갖는 페이지 단위 점진적 검사점을 사용하는 경우보다 프로세스의 평균 수행 시간을 현저히 줄임을 알 수 있다.

• 한국멀티미디어학회논문지
• /
• 제11권4호
• /
• pp.544-553
• /
• 2008

통상적인 센서 네트워크는 센서노드로부터 고정된 정보를 수집하는 일괄적인 방식을 사용한다. 하지만 이러한 방식은 헬스케어 환경에서 주요 센싱대상인 사람의 상태와 위치변화, 주변 환경의 변화에 능동적으로 대처하기 어렵다. 헬스케어 환경을 지원하기 위해서는 사람의 상태와 주변상황의 변화에 따른 특정정보를 제공해주어야 한다. 또한 사람의 이동에 따른 네트워크 타입의 변화에 대처하여야 한다. 본 논문에서는 대표적인 다중 에이전트 미들웨어인 Agilla 모델과 주변노드간의 클러스터를 구성함으로써 네트워크의 효율성을 보장하는 LEACH 프로토콜에 대해 분석한다. 이 분석 결과를 기반으로 기존 LEACH 프로토콜의 취약점인 노드 이동성을 보장하는 LEACH_Mobile 프로토콜을 제안한다. 또한 노드의 동적 기능변경을 지원하는 Mobility Agent Middleware와 LEACH_Mobile 라우팅 모듈을 구성요소로 이동노드의 동적 기능변경을 지원하는 Mobility Agent 모듈을 설계한다. 그리고 LEACH_Mobile 프로토콜의 시뮬레이션 결과를 통해 네트워크의 데이터 전송 성공률에 대한 성능 향상을 보여준다.

• 한국지반공학회논문집
• /
• 제36권6호
• /
• pp.17-34
• /
• 2020

일반적으로 잔교식 구조물의 내진설계를 위한 응답스펙트럼 해석 시 기준서들에서는 지진응답해석을 통해 증폭된 가속도를 입력가속도 활용하도록 제시하고 있으나, 기준서에 따라 방법이 상이하여 설계 시 혼란을 야기할 수 있다. 이에, 본 연구에서는 동적원심모형실험을 통해 지반 내 다양한 깊이에서 지반 가속도를 산정하였으며, 산정된 지반가 속도를 활용하여 응답스펙트럼 해석을 수행하였다. 이후 실험 및 해석을 통해 도출된 잔교식 안벽 구조물의 모멘트 결과를 비교하였으며, 응답스펙트럼 해석 시 적절한 입력지반가속도를 결정하기 위한 방법을 제시하고자 하였다. 실험 및 해석을 비교한 결과, 탄성 지반 스프링을 적용하는 경우 구조물의 고유주기를 가장 적절하게 모사하는 것으로 나타났으며, 상부 지표면에서 증폭된 지진파를 입력가속도로 활용하는 것이 사질토 지반에 관입된 구조물 응답을 가장 합리적으로 모사하는 것으로 나타났다.