• 대한건축학회논문집:구조계
• /
• 제34권6호
• /
• pp.29-34
• /
• 2018

In this research, regarding the cement supplied to ready mixed concrete plant, the feasibility of rapid acquisition test for cement fineness using hydrometer which used for early strength evaluation of concrete was analyzed. Additionally, regarding the rapid test with hydrometer control factors were provided. As a result of analysis, quality control using hydrometer was possible with the regressive equation obtained in five minute between density of suspension and fineness of cement powder. As the control factors, dispersing admixture, replacing kerosene as a medium, and temperature of cement and water were evaluated. According to the control factor evaluation, the tap water was optimum as a medium and calibration of keeping the temperature of water to $20^{\circ}C$ or correction factor was needed for density results. Finally, it is considered that the suggested rapid quality evaluation method using hydrometer is cheaper and easier method than currently used Blaine test.

• Journal of Ceramic Processing Research
• /
• 제19권5호
• /
• pp.428-433
• /
• 2018

In this study, using the pilot plant activation system, the activated cement has been manufactured and then applied to the manufacturing process of mineral hydrate insulating material. The fineness of the activated cement is controlled at $5,000cm^2/g$ and $7,500cm^2/g$ and the features of mineral hydrate insulating material, using OPC and the activated cement for each degree of fineness, has been analyzed. As the result of analyzing the crystal habit of the manufactured mineral hydrate insulting material, it is analyzed that the main crystal phase of specimen is tobermorite and some quartz peak has been detected. As the degree of fineness of the activated cement increases, the height of bubble of slurry increases as well, whereas the tendency for the density character to decrease has been detected. Along with it, as the density character decreases, the compression strength has decreases, whereas the tendency for the thermal characteristic to increases has been detected. The main features of mineral hydrate insulating material, using the activated cement with the fineness of $7,500cm^2/g$, the compression strength of 0.36 MPa, and the thermal conductivity of $0.044W/m{\cdot}K$, presents the excellent features as insulation.

• 한국건설순환자원학회논문집
• /
• 제8권1호
• /
• pp.1-7
• /
• 2020

고로슬래그 미분말은 뛰어난 장기 강도와 염해 저항성 등을 바탕으로 활발히 사용되는 혼화재들 중 하나이다. 국내 규격(KSF 2563)은 저분말도 GGBFS를 가지고 있는 일본 및 영국의 규격과는 다르게 3종의 GGBFS가 모두 고분말도에 포함된다. 본 연구에서는 4,000급 고로슬래그 미분말와 플라이애시를 혼입한 수화열 저감용 삼성분계 배합과 3,000급 GGBFS를 혼입한 배합의 굳지 않은 콘크리트 특성, 압축 강도, 수축 특성을 분석하였다. 수화열 저감용 삼성분계 배합과 저분말도 고로슬래그 미분말을 혼입한 배합 간에 공기량과 슬럼프는 동일한 값을 나타내었으며 초결 및 종결 시간의 경우 20분 내외의 결과를 나타내어 큰 차이가 나타나지 않았다. 압축 강도와 수축 특성 분석에서 삼성분계 배합은 저분말도 GGBFS를 혼입한 배합보다 더 낮은 장기 강도와 높은 수축량을 나타내었다.

• 한국건축시공학회지
• /
• 제9권4호
• /
• pp.139-145
• /
• 2009

본 연구에서는 입도분급에 의한 미분시멘트(FC)를 사용한 콘크리트의 강도 발현해석에 있어 FC 치환률 증가에 따른 분말도 변동이 콘크리트의 강도발현에 미치는 영향을 분석하기 위하여 기존 등가재령방법에 분말도의 영향을 고려할 수 있는 겉보기 활성화 에너지 모델을 이용하는 방법으로 FC 치환 콘크리트의 강도발현해석을 실시하고자 한다. 연구결과에 따르면 FC 치환률 변화에 따른 시멘트의 분말도 증가를 수화반응속도에 반영한 겉보기 활성화 에너지(Ea)식을 이용하여 강도발현 해석을 수행한 결과 예상과 다르게 FC 치환률이 증가함에 따라 상당부분 정확도가 저하하는 것으로 나타났고, 기존의 응결시간에 의한 방법보다도 역시 정확도가 저하함을 알 수 있었다. 금후의 과제로서 분말도의 영향을 보다 합리적으로 고려할 수 있는 Ea 산정모델의 개발을 통해 FC 치환률에 따른 콘크리트의 정확한 강도발현 해석을 수행할 필요가 있을 것으로 사료된다.

• 한국주조공학회지
• /
• 제25권4호
• /
• pp.173-178
• /
• 2005

The vacuum molding process is one of the clean-foundry molding-processes that can recycle molding sands repeatedly, because molding can be accomplished by introducing vacuum only among dry molding sands in flask. The effects of molding conditions such as sand grain fineness, vacuum pressure and coating thickness on the fluidity of A356 Al alloy were studied and the results was obtained that the fluidity length was decreased as the sand grain fineness number and coating thikness were decreased and the vacuum pressure was increased. A large amount of heat removal from the molten metal resulting from the vacuum suction during the vacuum molding process was the principal cause of this decrease in fluidity.

• 한국세라믹학회지
• /
• 제44권2호
• /
• pp.103-109
• /
• 2007

In this study, the rheological properties of cement pastes containing blastfurnace slag of different fineness were investigated. The fluidity of cement pastes with low Blaine value blastfurnace slag was increased with decreasing the plastic viscosity and the yield stress of pastes. And the optimum dosage of polycarboxylate type superplasticizer to the cement pastes was confirmed according to the fineness and the replacement ratio of blastfurnace slag. All cement pastes showed the thixotropy behavior. And also it was formed that the segregation range of cement pastes was occurred below $10D/cm^2$ of the yield stress and below 350 cPs of the plastic viscosity by the coaxial cylinder viscometer.

• 한국건축시공학회지
• /
• 제7권1호
• /
• pp.85-90
• /
• 2007

According as industry develops rapidly, problem of resources exhaustion and environmental pollution is appearing. Way to use construction waste that is development of new compound material and Industry product is required. Limestone powder that is Industry product is $CaCO_3$. and vicosity is promotion effect because there is no damage to hydration of cement and powder is very thin and water tightness increases. This research purposed to analyze concrete property changing limestone fineness. According as the limestone powdered replacement ratio increases, slump and unit capacity mass increased, and the air content decreased according as the replacement ratio increases. Compressive strength and tensile strength decreased according as the limestone powder replacement ratio increases.

• 한국콘크리트학회:학술대회논문집
• /
• 한국콘크리트학회 1995년도 봄 학술발표회 논문집
• /
• pp.72-77
• /
• 1995

Blast-furnace slag cement has been used widely as a structural material due to the latent hydraulicity of granulated ground blast furnace slag(GGBS)for a long time as The wall as ordinary portland cement. In this study, based on the fundamental investigation on the high strength and high durable concrete using the high fineness GGBS the following remarks can be made. 1) The average desired strenth of concrete is Or=600~800kg/$\textrm{cm}^2$. 2) The above high strength concrete using the high fineness GGBS is more workable than those using only OPC. 3) The adiabatic temperature and drying shringkage decrease, so the density and resistance to sea water attack increase as results. 4)The unit cement content and unit air entrained admixture at the same desired strength of concrete decrease, so the economical high strength concrete can be manufactured from using the high fineness GGBS.

• 콘크리트학회논문집
• /
• 제12권1호
• /
• pp.45-52
• /
• 2000

The quality of cement mortar products largely depends on various work conditions, specially on the grading and grade shape of aggregates. However, the effect of grading and grade shape on the quality is not considered by both KS codes and production processes, resulting in the increase of the possibility of quality degradation. The objective of this study was to investigate the effect of grading and grade shape on the strength and absorption characteristics of cement mortar products. Flexural and compressive strength increased with the increase of fineness modulus and W/C. The strength increase was measured larger with river sand than with crushed sand. Absorption tended to decrease with the increase of fineness modulus and W/C, but did not affected by the source of sand.

• 대한가정학회지
• /
• 제11권1호
• /
• pp.26-43
• /
• 1973

This study was carried out on the Sewbility of Urethane Foam usually used as coldproof lining. The Sewability was estimated with the Puckering Grade and Seam Efficiency according to the thicknes of urethane foam, fineness and material of sewing thread, and the sort of covering fabric. The result shows the following ; 1. The thick foam proportinally shows the low Puckering Grade. 2. Effect on the sewability is small in fineness of sewing thread but large in material. Especially silk thread shows the greatest sewability in foam sewing. When the material of covering fabric is same as that of sewing thread (for example ; p/c fabric and p/c thread) the sewability is excellent in special. 3. Taffeta in covering foam is not suitable to foam sewing, satin and twill show superior sewability without reagrd to the thickness of foam. 4. In case of sewing foam covered with tricot, optimum thickness of foam and fineness of sewing thread through pretest must determine. 5. The thicker foam is the better seam efficiency tends, and Seam Efficiency largely effects to the strength of the sewing thread itself. 6. The seam Efficiency can heighten with the strength of sewing thread in proportion to that of covering fabric.