• Geomechanics and Engineering
• /
• 제31권2호
• /
• pp.167-181
• /
• 2022

Soil liquefaction has been one of the most important concerns in geotechnical earthquake engineering in recent years, due to its damages to structures and its destructive effects. The cyclic liquefaction of silty sands, in particular, remains of great interest for both research and application. Although many factors are known that affect the liquefaction resistance of sands, the effect of fine grain content is perhaps one of the most studied and still controversial. In this study, 48 deformation-controlled cyclic simple shear tests were performed on BS and CS silt samples mixed with 5%, 15% and 30% by weight of Krk085, Krk042 and Krk025 sands in constant-volume conditions to determine the liquefaction potential of silty sands. The tests were carried out at 30% and 50% relative density and under 100 kPa effective stress. The results revealed that the liquefaction potential of silty sand increases with increasing average particle size ratio (D_50sand / d_50silt) of the mixture for a fixed silt content. Furthermore, for identical base sand, the liquefaction potentials of coarse grained sands increase with increasing silt content, while the respective potentials of fine grained sands generally decrease. However, this situation may vary depending on the silt grain structure and is affected by the nature of the fine grains. In addition, the variation of the void ratio interval was shown to provide a good intuition in determining the liquefaction potentials of silty sands, while the intergranular void ratio alone does not constitute a criterion for determining the liquefaction potentials of silty sands.

• Computers and Concrete
• /
• 제20권2호
• /
• pp.145-154
• /
• 2017

In geological engineering, grouting with Portland cement is a common technique for ground improvement, during which micro-fine cement is applied as a slurry, such that it intrudes into soil voids and decreases soil porosity. To determine the utility and behavior of cements with different Blaine values (index of cement particle fineness) for stabilization of fine sand, non-destructive and destructive tests were employed, such as laser-ray determination of grain size distribution, and sedimentation, permeability, and compressive strength tests. The results of the experimental study demonstrated a suitable mix design for the upper and lower regions of the cement-grading curve that are important for grouting and stabilization. Increasing the fineness of the cement decreased the permeability and increased the compressive strength of grouted sand samples considerably after two weeks. Moreover, relative to finer (higher Blaine value) or coarser (lower Blaine value) cements, cement with a Blaine value of $5,100cm^2/g$ was optimal for void reduction in a grouted soil mass. Overall, study results indicate that cement with an optimum Blaine value can be used to satisfy the designed geotechnical criteria.

• Advances in materials Research
• /
• 제3권2호
• /
• pp.61-75
• /
• 2014

This study aimed to investigate the suitability of some concrete components for producing "high-performance heavy density concrete" using different types of aggregates that could enhances the shielding efficiency against ${\gamma}$-rays. 15 mixes were prepared using barite, magnetite, goethite and serpentine aggregates along with 10% silica fume, 20% fly ash and 30% blast furnace slag to total OPC content for each mix. The mixes were subjected to compressive strength at 7, 28 and 90 days. In some mixes, compressive strengths were also tested up to 90 days upon replacing sand with the fine portions of magnetite, barite and goethite. The mixes containing magnetite along with 10% SF reaches the highest compressive strength exceeding over M60 requirement by 14% after 28 days. Whereas, the compressive strength of concrete containing barite was very close to M60 and exceeds upon continuing for 90 days. Also, the compressive strength of high-performance concrete incorporating magnetite fine aggregate was significantly higher than that containing sand by 23%. On the other hand, concrete made with magnetite fine aggregate had higher physico-mechanical properties than that containing barite and goethite. High-performance concrete incorporating magnetite fine aggregate enhances the shielding efficiency against ${\gamma}$-rays.

• 한국건축시공학회:학술대회논문집
• /
• 한국건축시공학회 2015년도 춘계 학술논문 발표대회
• /
• pp.71-72
• /
• 2015

As this study is the one related to the ultra high strength concrete essentially used for high rise buildings, it has analyzed on the flowability of ultra high strength concrete according to the variation of coarse aggregate and fine aggregate. The coarse aggregate was planned as two types including Granite Aggregate (GA) and crushed coarse Limestone Aggregate (LA) while fine aggregate was planned as four types including Sea Sand (SS), Limestone Crushed Fine Aggregates (LFA), Electric Arc Furnace Oxidizing Slag Aggregates (EFA) and Crushed Sand (CS) to perform experiment with a total of eight variables. As a result of analyzing slump flow, 500mm concentration time, U-Box and L-Flow, etc. among the characteristics of fresh concrete, a mix using LA+LFA is determined to show high flowability in case of applying ultra high strength concrete.

• Advances in concrete construction
• /
• 제5권6호
• /
• pp.671-683
• /
• 2017

Commonly used concrete in general, consists of cement, fine aggregate, coarse aggregate and water. Natural river sand is the most commonly used material as fine aggregate in concrete. One of the important requirements of concrete is that it should be durable under certain conditions of exposure. The durability of concrete is defined as its ability to resist weathering action, chemical attack or any other process of deterioration. Durable concrete will retain its original form, quality and serviceability when exposed to its environment. Deterioration can occur in various forms such as alkali aggregate expansion, freeze-thaw expansion, salt scaling by de-icing salts, shrinkage, attack on the reinforcement due to carbonation, sulphate attack on exposure to ground water, sea water attack and corrosion caused by salts. Addition of admixtures may control these effects. In this paper, an attempt has been made to replace part of fine aggregate by tailing material and part of cement by fly ash to improve the durability of concrete. The various durability tests performed were chemical attack tests such as sulphate attack, chloride attack and acid attack test and water absorption test. The concrete blend with 35% Tailing Material (TM) in place of river sand and 20% Fly Ash (FA) in place of OPC, has exhibited higher durability characteristics.

• 한국해양생명과학회지
• /
• 제3권1호
• /
• pp.38-43
• /
• 2018

대형저서동물에서 우점하고 있는 갯지렁이류는 퇴적층의 유기물 섭취를 통하여 저질환경개선에 중요한 역할을 한다. 본 연구에서는 최근 양식기술이 개발된 바위털갯지렁이를 이용하여 갯벌 퇴적층의 유기물 제거효과를 검토하였다. 이를 위하여 입자특성이 다른 세종류의 저질환경(S1: 강사질, S2: 해사질, S3: 니사질)에서 해수 및 퇴적층의 TOC를 측정하였다. 바위털갯지렁이는 세종류의 입자특성에서 모두 유기물 제거효과를 나타내었으며, 입자가 클수록 제거율이 높았다. 유기물 정화능력을 정량적으로 평가한 결과 바위털갯지렁이는 각 저질별로 강사질에서 3.9856 ppm g^-1d^-1, 해사질에서 2.8021 ppm g^-1d^-1, 그리고 니사질에서 28.1142 ppm g^-1d^-1의 제거능력을 나타내었다. 본 연구결과는 바위털갯지렁이가 다양한 저질에서 유기물 제거에 기여하고 있음을 보여 주었다.

• 한국물환경학회지
• /
• 제37권4호
• /
• pp.286-295
• /
• 2021

The removal efficiency of road-deposited sediment (SDR) by road sweeping was analyzed by performing particle size analysis before and after road sweeping at four highways during May to December 2019. The SDR accounted for the largest proportion in the range of 250 to 850 ㎛ and the degree of its proportion had an effect on the particle size distribution curve. The particle size distribution of the collected sediments showed a similar distribution at all sites. Below 75 ㎛, the removal efficiency of SDR showed a constant value around 40%, but above 75 ㎛, it increased as the particle size increased. The removal efficiency was 82-90% (average 86%) for gravel, 66-93% (average 79%) for coarse sand, 35-92% (average 64%) for fine sand, 29-69% (average 44%) for very fine sand, 19-58% (average 40%) for silt loading, 10-59% (average 40%) for TSP, 13-57% (average 40%) for PM10, and 15-61% (average 38%) for PM2.5. SDR removal efficiency showed an average of 69% for the four highways. It was found that if the amount of SDR was less than 100 g/m², it was affected by the road surface condition and had a large regional deviation. As such, the amount of SDR and the removal efficiency increased. The fine particles, which have relatively low removal efficiency, contained a large amount of pollutants, which is an important factor in water and air pollution. Therefore, various measures to improve the removal efficiency of fine particles in SDR by road sweeping are needed.

• 한국초지조사료학회지
• /
• 제8권1호
• /
• pp.55-60
• /
• 1988

A two year's field experiment was conducted on newly reclaimed saline tidal lands to measure the effects of sand mulching on salinity of the soils and their relationship to crop performance. Hybrid sorghum cv. Pioneer 931 was grown under different mulching treatments using of medium sand and red earth (Fine loamy, Typic Hapludults). Salinity in the root zone was decreased markedly under soil mulching using of medium sand, especially during the dry season, and it caused a great increase in the root growth and R/T ratio. Seasonal values of electrical conductivity at sand mulching were 6.6 in April and 1.6 mmhos in August, but it was still high with a concentration of 12.7 (April) and 3.8 mmhos (August) in untreated check plot. Sand mulching increased plant growth and the rate of dry matter accumulation. However, treatment of red earth additionally over sand mulching produced lower dry matter yield than those of soil mulching using of medium sand only. Under salt stress sorghum plant showed a decrease in the leaf weight ratio (LWR) and it resulted in a low concentration of crude protein of the plant. Sand mulching enhanced leaf weight ratio and rate of protein synthesis.

• Advances in concrete construction
• /
• 제2권1호
• /
• pp.13-27
• /
• 2014

The principal objective of this study is to deepen the characterization studies already led on sand concretes in previous works. Indeed, it consists in studying the effect of the sand type on the main properties of sand concrete: fracture and mechanical properties. We particularly insist on the determination of the fracture characteristics of this material which apparently have not been studied. To carry out this study, four different types of sand have been used: dune sand (DS), river sand (RS), crushed sand (CS) and river-dune sand (RDS). These sands differ in mineralogical nature, grain shape, angularity, particle size, proportion of fine elements, etc. The obtained results show that the particle size distribution of sand has marked its influence in all the studied properties of sand concrete since the sand having the highest diameter and the best particle size distribution has given the best fracture and mechanical properties. The grain shape, the angularity and the nature of sand have also marked their influence: thanks to its angularity and its limestone nature, crushed sand yielded good results compared to river and dune sands which are characterized by rounded shape and siliceous nature. Finally, it should further be noted that the sand concrete presents values of fracture and mechanical properties slightly lower than those of ordinary concrete. Compared to mortar, although the mechanical strength is lower, the fracture parameters are almost comparable. In all cases, the sand grains are debonded from the paste cement during the fracture which means that the crack goes through the paste-aggregate interface.

• 산업기술연구
• /
• 제17권
• /
• pp.227-232
• /
• 1997

This study was conducted to evaluate durability of concrete which are increasingly demanded recently. Concrete durability properties incorporating waste foundry sand was performed with the variable of W/C ratio, Sand/Waste foundry sand ratio and Air entrainment-Non air entrainment. Cylinder specimens were made and subjected to freezing and thawing cycle at $-18^{\circ}C$ and $4^{\circ}C$. Dynamic modulus of elasticity were evaluated as F/T cycle increase. The results show that decreasing W/C ratio and AE concrete makes improved resistance of freezing and thawing improved. Especially, resistance of freezing and thawing is improved by Fine aggregate/Waste foundry sand ratio which is 50%, 25%, 0% in a row.