• 센서학회지
• /
• 제24권3호
• /
• pp.181-187
• /
• 2015

The magnetoelectric characteristics on layered $Fe_{78}B_{13}Si_9/PZT$ and $Fe_{78}B_{13}Si_9/PZT/Fe_{78}B_{13}Si_9$($t_m=0.017$, 0.034mm) composites by epoxy bonding for magnetic field sensor were investigated in the low-frequency range and resonance frequency range. The optimal bias magnetic field $H_{dc}$ of these samples was about 23~63 Oe range. The Me coefficient of $Fe_{78}B_{13}Si_9/PZT/Fe_{78}B_{13}Si_9(t_m=0.034mm)$ composites reaches a maximum of $186mV/cm{\cdot}Oe$ at $H_{dc}=63Oe$, f=50 Hz and a maximum of $1280mV/cm{\cdot}Oe$ at $H_{dc}=63Oe$, resonance frequency $f_r=95.5KHz$. The output voltage shows linearity proportional to ac fields $H_{ac}$ and is about U=0~130.6 mV at $H_{ac}=0{\sim}7Oe$, f=50 Hz, U=0~12.4 V at $H_{ac}=0{\sim}10Oe$, $f_r=95.5KHz$(resonance frequency). The optimal frequency(f=50 Hz) of this sample is around the utility ac frequency(f=60 Hz). Therefore, this sample will allow for ac magnetic field sensor at utility frequency and low bias magnetic fields $H_{dc}$.

• Wind and Structures
• /
• 제29권6호
• /
• pp.471-488
• /
• 2019

Wind pressure is a critical argument for the wind-resistant design of structures. The attempt, however, to explore the wind pressure field on buildings still encounters challenges though a large body of researches utilizing wind tunnel tests and wind field simulations were carried out, due to the difficulty in logical treatments on the scale effect and the modeling error. The full-scale measurement has not yet received sufficient attention. By performing a field measurement, the present paper systematically addresses wind pressures on the rectangular attic of a double-tower building. The spatial and temporal correlations among wind speed and wind pressures at measured points are discussed. In order to better understand the wind pressure distribution on the attic facades and its relationship against the approaching flow, a full-scale CFD simulation on the similar rectangular attic is conducted as well. Comparative studies between wind pressure coefficients and those provided in wind-load codes are carried out. It is revealed that in the case of wind attack angle being zero, the wind pressure coefficient of the cross-wind facades exposes remarkable variations along both horizontal and vertical directions; while the wind pressure coefficient of the windward facade remains stable along horizontal direction but exposes remarkable variations along vertical direction. The pattern of wind pressure coefficients, however, is not properly described in the existing wind-load codes.

• 한국산학기술학회논문지
• /
• 제19권7호
• /
• pp.214-221
• /
• 2018

본 연구의 목적은 노지감귤의 출하구조를 순별, 월별로 구분하여 분석한다. 이를 위해 노지감귤의 가격신축성함수를 추정, 분석함으로써 어떻게 출하조절을 하는 것이 노지감귤농가의 소득을 안정시키고, 증대시킬 수 있는지를 모색하고, 이에 따른 정책적 함축성을 도출하는 것이다. 노지감귤 출하물량 1% 증가에 따른 순별 가격신축성은 시기에 따라 상이하게 나타나고 있는데, 10월 하순에서 1월 초순까지의 하락폭이 큰 것으로 나타나 이 시기의 출하조절의 필요성이 크다. 품질이 떨어지는 해를 나타내는 더미변수인 DUM_Q의 부호는 (-)이고, 통계적으로 유의미한 결과를 보여주고 있다. 설날 연후 7일 이상이 2월에 들어있는 해를 나타내는 더미변수인 DUM02의 10월 초순부터 1월 하순까지의 부호가 (-)를 보이고 있다. 이는 설날이 1월에 있는 경우보다 2월에 있는 경우가 물량증대에 따른 하락폭이 크다는 것을 나타낸다. 노지감귤의 출하물량 1% 증대에 따른 월별 가격신축성은 상이하게 나타나고 있는데, 10월에서 12월까지의 하락폭이 큰 것으로 나타나 이 시기의 출하조절의 필요성이 요구된다. 품질이 떨어지는 해를 나타내는 더미변수인 DUM_Q의 부호는 (-)이고, 통계적으로 유의미한 결과를 보여주고 있다. 설날 연후 7일 이상이 2월에 들어있는 해를 나타내는 더미변수인 DUM02의 10월부터 1월까지의 부호가 (-)를 보이고 있다. 이는 설날이 1월에 있는 경우보다 2월에 있는 경우가 물량증대에 따른 하락폭이 크다는 것을 나타낸다. 그리고 순별 및 월별 가격신축성함수의 더미변수인 DOM_Q와 DUM02의 부호가 음(-)을 보인다는 것은, 품질이 좋은 해보다 품질이 나쁜 경우에, 그리고 설날이 1월에 있는 경우보다 2월에 있는 경우에 출하조절의 필요성이 더 중요함을 의미한다.

• Advances in materials Research
• /
• 제4권3호
• /
• pp.165-178
• /
• 2015

Friction coefficient of epoxy metal matrix composites were investigated. The main objective was to increase the friction coefficient through rubber sole sliding against the epoxy floor coating providing appropriate level of resistance. This was to avoid the excessive movement and slip accidents. Epoxy metal matrix composites were reinforced by different copper wire diameters. The epoxy metal matrix composites were experimentally conducted at different conditions namely dry, water and detergent wetted sliding, were the friction coefficient increased as the number of wires increased. When the wires were closer to the sliding surface, the friction coefficient was found to increase. The friction coefficient was found to increase with the increase of the copper wire diameter in epoxy metal matrix composites. This behavior was attributed to the fact that as the diameter and the number of wires increased, the intensity of the electric field, generated from electric static charge increased causing an adhesion increase between the two sliding surfaces. At water wetted sliding conditions, the effect of changing number of wires on friction coefficient was less than the effect of wire diameter. The presence of water and detergent on the sliding surfaces decreased friction coefficient compared to the dry sliding. When the surfaces were detergent wetted, the friction coefficient values were found to be lower than that observed when sliding in water or dry condition.

• 한국전산유체공학회:학술대회논문집
• /
• 한국전산유체공학회 2011년 춘계학술대회논문집
• /
• pp.199-201
• /
• 2011

NACA0012 Airfoil was simulated with Computational Fluid Dynamics(CFD) and the aerodynamic characteristics was analyzed for various far-field boundary distances ranging from 10 airfoil chord to 50 chord Drag coefficient distribution was dependent on the far-field distance and circulation, integrated along the loop inside the flow region, was also dependent. It was turned out that some corrections based on the circulation should be added to the far-field boundary condition for accurate airfoil simulation.

• 대한의용생체공학회:의공학회지
• /
• 제16권4호
• /
• pp.387-394
• /
• 1995

박막광도파로 센서의 특소전파상수를 이용하여 인간혈액내의 산화 및 환원 혈색소의 흡광계수를 쉽고 빠르게 측정할 수 있는 방법을 제안한다. 제작된 광도파로위에 에바네센트 필드와 시료간의 상호작용길이를 변화시킬수 있도록 직렬의 다채널 시료 충전셀을 만들고 여러가지 농도의 두가지 혈색소 시료들에 대한 센서응답을 조사하여 상호작용길이에 대한 의존성을 살펴보았다. 센서응답은 상호작용길이와 시료의 농도에 선형적으로 비례한다. 시료들과 에바네센트 필드 흡수에 따른 제작된 센서의 감쇄정수를 실험적으로 구하고 제한된 방법으로 흡광계수를 결정한다. 제안된 방법으로 구한 두가지 혈색소에 대한 흡광계수는 종래의 투과광 측정법으로 구한 값과 잘 일치한다.

• 대한방사선기술학회지:방사선기술과학
• /
• 제44권4호
• /
• pp.343-350
• /
• 2021

3D printing technology is an additive manufacturing technology produced through 3D scanning or modeling method. This technology can be produced in a short time without mold, which has recently been applied in earnest in various fields. In the medical field, 3D printing technology is used in various fields of radiology and radiation therapy, but related research is insufficient in the field of nuclear medicine. In this study, we compare the characteristics of traditional nuclear medicine phantom with 3D printing technology and evaluate its applicability in clinical trials. We manufactured the same size phantom of poly methyl meta acrylate(PMMA) and acrylonitrile butadiene styrene(ABS) based on the aluminum step wedge. We used BrightView XCT(Philips Health Care, Cleveland, USA) SPECT/CT. We acquired 60 min list mode for Aluminum, PMMA and ABS phantoms using Rectangular Flood Phantom (Biodex, New York, USA) ^99mTcO₄ 3 mCi(111 MBq), 6 mCi (222MBq) and ⁵⁷Co Flood phantom(adq, New Hampshire, USA). For the analysis of acquired images, the region of interest(ROI) were drawn and evaluated step by step for each phantom. Depending on the type of radioisotope and radiation dose, the counts of the ABS phantom was similar to that of the PMMA phantom. And as the step thickness increased, the counts decreased linearly. When comparing the linear attenuation coefficient of Aluminum, PMMA and ABS phantom, the linear attenuation coefficient of the aluminium phantom was higher than that of the others, and the PMMA and ABS phantom had similar the linear attenuation coefficient. Based on ABS phantom manufactured by 3D printing technology, as the thickness of the PMMA phantom increased, the counts and linear attenuation coefficient decreased linearly. It has been confirmed that ABS phantom is applicable in the clinical field of nuclear medicine. If the calibration factor is applied through further research, it is believed that practical application will be possible.

• 전기학회논문지P
• /
• 제58권1호
• /
• pp.44-47
• /
• 2009

This paper describes the information for quantitative simulation of weakly ionized plasma. We must grasp the meaning of the plasma state condition to utilize engineering application and to understand materials of plasma state. $SF_6$ gas is widely used in industrial of insulation field. In this paper, $N_2$ is mixed to improve pure $SF_6$ gas characteristics. Electron transport coefficients in $SF_6-N_2$ mixture gases are simulated in range of E/N values from 70 to 400 [Td] at 300K and 1 Torr by using Boltzmann equation method. The results of this method. which are ionization coefficient, attachment coefficient, effective ionization coefficient, and critical E/N, can be important data to present characteristic of gas for insulation. Specially critical E/N is a data to evaluate insulation strength of a gas and is presented in this paper for various mixture ratios of $SF_6-N_2$ mixture gases.

• 대한기계학회:학술대회논문집
• /
• 대한기계학회 2008년도 추계학술대회A
• /
• pp.701-705
• /
• 2008

Design analysis and computer experiments (DACE) model is widely used to express efficiently the nonlinear responses in the field of engineering design. Kriging model, a DACE model, can approximately replace a simulation model that is very expensive or highly nonlinear. The kriging model is composed of the summation of a global model and a local model representing deviation from global model. The local model is determined by correlation coefficient of the pre-sampled points, where determination of the correct correlation coefficient has an effect on accuracy and robustness of the kriging model. Therefore, robustness of the correlation coefficient is explored with respect to degrees of the global model. Then we propose the range of correlation coefficient to make correct and robust kriging model and the influence of the correlation coefficients on the degrees of global model with respect to the nonlinearity of the pre-sampled responses.

• 한국신재생에너지학회:학술대회논문집
• /
• 한국신재생에너지학회 2011년도 추계학술대회 초록집
• /
• pp.160.1-160.1
• /
• 2011

In this study, the influence of methodology of assessing water levels on the discharge coefficient of sluice for tidal power generation was investigated. A physical experiment was performed in a planar open channel by installing 1/70 scale model of the sluice caisson in the planar open channel. In front of and behind the sluice model, sloping bathymetry was made to reproduce corresponding field condition. By analyzing the experimental results, it was found that the location of measuring water levels significantly affects the estimates of the discharge coefficient, due to the variability of the parameter according to the head difference between the measuring locations. Therefore, it is necessary to be careful in estimating and utilizing the discharge coefficient in the relevant study of a tidal power generation.