• Journal of Adhesion and Interface
• /
• v.12 no.3
• /
• pp.88-93
• /
• 2011

Optimal dispersion and fabrication conditions of carbon nanotube (CNT) embedded in phenolic resin were determined by electrical resistance measurement; and interfacial property was investigated between plasma treated carbon fiber and CNT-phenolic composites by electro-micromechanical techniques. Wettability of carbon fiber was improved significantly after plasma treatment. Surface energies of carbon fiber and CNT-phenolic nanocomposites were measured using Wilhelmy plate technique. Since surface activation of carbon fiber, the advancing contact angle decreased from $65^{\circ}$ to $28^{\circ}$ after plasma treatment. It was consistent with static contact angle results of carbon fiber. Work of adhesion between plasma treated carbon fiber and CNT-phenolic nanocomposites was higher than that without modification. The interfacial shear strength (IFSS) and apparent modulus also increased with plasma treatment of carbon fiber.

• Journal of Adhesion and Interface
• /
• v.23 no.4
• /
• pp.122-129
• /
• 2022

In this study, the hydrophilicity of the metal fiber is improved by introducing an oxygen-containing functional group to the fiber surface after treatment of the metal fiber using the oxygen plasma treatment time as an experimental variable. For the surface modification of metal fibers, changes in surface properties before and after plasma treatment were observed using SEM and x-ray photoelectron spectroscopy (XPS). In order to observe the effect of the plasma treatment time on the surface of the metal fiber, the change in contact angle of the metal fiber with respect to a polar solvent and a non-polar solvent was measured. After calculating the change in surface free energy using the measured contact angle, the contact angle and the surface free energy for metal fibers before and after oxygen plasma treatment were compared, and the correlation with the adhesion work was also considered. The microdroplet specimens were prepared to investigate the effect of surface changes of these metal fibers on the improvement of shear strength at the interface when combined with other materials and the interfacial shear strength was measured, and the correlation with the adhesion work was also identified. Therefore, the oxygen plasma treatment of the metal fiber results in an increase in the physical surface area on the fiber surface and a change in contact angle and surface energy according to the introduction of the oxygen-containing functional group on the surface. This surface hydrophilization resulted in improving the interfacial shear strength with the polymer resin.

• Smart Structures and Systems
• /
• v.20 no.2
• /
• pp.163-173
• /
• 2017

Structural health monitoring (SHM) of civil infrastructure using fiber Bragg grating sensor networks (FBGSNs) has received significant public attention in recent years. However, there is currently little research on the health-monitoring technology of high-piled wharfs in coastal ports using the fiber Bragg grating (FBG) sensor technique. The benefits of FBG sensors are their small size, light weight, lack of conductivity, resistance corrosion, multiplexing ability and immunity to electromagnetic interference. Based on the properties of high-piled wharfs in coastal ports and servicing seawater environment and the benefits of FBG sensors, the SHM system for a high-piled wharf in the Tianjin Port of China is devised and deployed partly using the FBG sensor technique. In addition, the health-monitoring parameters are proposed. The system can monitor the structural mechanical properties and durability, which provides a state-of-the-art mean to monitor the health conditions of the wharf and display the monitored data with the BIM technique. In total, 289 FBG stain sensors, 87 FBG temperature sensors, 20 FBG obliquity sensors, 16 FBG pressure sensors, 8 FBG acceleration sensors and 4 anode ladders are installed in the components of the back platform and front platform. After the installation of some components in the wharf construction site, the good signal that each sensor measures demonstrates the suitability of the sensor setup methods, and it is proper for the full-scale, continuous, autonomous SHM deployment for the high-piled wharf in the costal port. The South 27# Wharf SHM system constitutes the largest deployment of FBG sensors for wharf structures in costal ports to date. This deployment demonstrates the strong potential of FBGSNs to monitor the health of large-scale coastal wharf structures. This study can provide a reference to the long-term health-monitoring system deployment for high-piled wharf structures in coastal ports.

• Composites Research
• /
• v.22 no.5
• /
• pp.8-14
• /
• 2009

Interfacial evaluation of glass fiber reinforced carbon nanotube (CNT)-epoxy nanocomposite was investigated by micromechanical technique in combination with wettability test. The contact resistance of the CNT-epoxy nanocomposite was measured using a gradient specimen, containing electrical contacts with gradually-increasing spacing. The contact resistance of CNT-epoxy nanocomposites was evaluated by using the two-point method rather than the four-point method. Due to the presence of hydrophobic domains on the heterogeneous surface, the static contact angle of CNT-epoxy nanocomposite was about $120^{\circ}$, which was rather lower than that for super-hydrophobicity. For surface treated-glass fibers, the tensile strength decreased dramatically, whereas the tensile modulus exhibited little change despite the presence of flaws on the etched fiber surface. The interfacial shear strength (IFSS) between the etched glass fiber and the CNT-epoxy nanocomposites increased due to the enhanced surface energy and roughness. As the thermodynamic work of adhesion, $W_a$ increased, both the mechanical IFSS and the apparent modulus increased, which indicated the consistency with each other.

• The Korean Journal of Food And Nutrition
• /
• v.16 no.4
• /
• pp.372-378
• /
• 2003

The volatile components of cinnamon bark were extracted by using different isolation methods, simultaneous distillation extraction (SDE) and solid phase microextraction (SPME). Then the volatile components were analyzed by gas chromatography(GC) and mass selective detector(MSD). 30 compounds were identified in cinnamon bark. In SPME technique, several factors influencing the equilibrium of the aroma compounds between sample and SPME fiber was taken into account, including the kind of SPME fiber, extraction temperature and extraction time. Four different SPME fibers were tested, namely polydimethylsiloxane (PDMS), poly acrylate(PA), divinyl- benzene-carboxen-polydimethylsiloxane (DVB/CAR/PDMS) and carbowax/divinylbenzene(CW/DVB). Among these SPME fiber, PDMS coating fiber showed the best results. The profile of volatile compounds of cinnamon bark at different extraction temperature and extraction time were investigated by 100$\mu\textrm{m}$ PDMS fiber.

• Journal of Sensor Science and Technology
• /
• v.13 no.2
• /
• pp.96-100
• /
• 2004

Optical fiber sensors have been used to detect small amounts of chemical species. In this work, a new thin polymer-clad fiber sensor is developed. Polyaniline is chemically synthesized and thin clad layers of the polymer are easily deposited on optical fiber by dip-coating technique. The optical property of polyaniline as a sensing material is analyzed by UV-Vis-NIR. The light source is stabilized He-Ne laser at 635 nm wavelength with 1 mW power. The light power transmitted through the optical fiber is measured with a spectrophotometer. By selecting a fixed incident angle, variation of transmitted light intensity through the optical fiber can be detected as gas molecules absorbed in the polyaniline clad layer. Among the various gases, the fabricated optical fiber sensor shows good sensitivity to $NH_{3}$ gas. The optical fiber sensors was shown more improved properties than polymer based sensors which measure conductivity changes.

• Advances in concrete construction
• /
• v.6 no.5
• /
• pp.423-463
• /
• 2018

This paper investigates the behavior of normal and self-compacted steel fiber reinforced concrete (SCC-SFRC) corbels rehabilitated by Basalt Fiber Mesh (BFM) and Basalt Fiber Fabric (BFF) for the first time in literature. The research objective is to study the effectiveness of BFM and BFF in the rehabilitation of damaged reinforced concrete corbels with and without epoxy injection. The experimental program includes two types of concrete: normal concrete, and self-compacted concrete. For normal concrete, 12 corbels were rehabilitated by BFM without injection epoxy in cracks, with two values of compressive strength, three ratios of steel fiber (SF), and two values of shear span. For self-compacted concrete, 48 corbels were rehabilitated with different parameters where 12 corbels were rehabilitated by BFM with and without epoxy injection, 18 heated corbels with three different high-temperature level were rehabilitated by repairing cracks only by epoxy injection, and 18 heated corbels with three different high-temperature level were rehabilitated by repairing cracks by epoxy and wrapping by BFF. All 48 corbels have two values of compressive strength, three values volumetric ratios of SF, and two values of the shear span. Test results indicate that RC corbels rehabilitated by BFM only without injection did not show any increase in the ultimate load capacity. Moreover, For RC corbels that were repaired by epoxy without basalt wrapping, the ultimate load capacities showed an increase depending on the mode of failure of corbels before the rehabilitation. However, the rehabilitation with only crack repairing by epoxy injection is more effective on medium strength corbels as compared to high strength ones. Finally, it can be concluded that use of BFF is an effective and powerful technique for the strengthening of damaged RC corbels.

• Archives of design research
• /
• no.16
• /
• pp.237-252
• /
• 1996

Study of new materials, which has been going on in many fields of modem art since the beginning of this century, has cintributed much to the development of modem art. In this regard, it is noteworthy that many in the field of fiber art have experimented with non-traditional, indusrial materials with some notable success. Industrial materials represent the world of thechnology we live in and help us form the kind of view on art that is reflective of the present age and its social milieu. Industrial materials, when used as media for art, also present us with new concepts and possibilities for artistic expression. In fiber art, the use of industrial materials has greatly expanded the very idea of 'fiber', effectively ferring the imagination of fiber aetists to experiment with diverse materials and new mathodology. Overcoming the traditional constraints of technique-orienthd their discipline, fiber artists began to pay more attention to matiere or the material jtself and the infinite variety of surface, color and texture that it promises. And informed by this newly discovered aesthetice of the material. fiber artists began in eamest to expand the area of their artistic expression, producing multi-dimensional works, conquering space and experimentiong with hugc environmantal works.

• Journal of the Korea institute for structural maintenance and inspection
• /
• v.3 no.3
• /
• pp.223-236
• /
• 1999

The need to monitor and undertake remidial works on large structures has greatly increased in recent years due to the appearance of widespread faults in large structures such as bridges and buildings, etc, of 20 or more years of age. The health condition of structures must be monitored continuously to maintenance the structures. In order to do in-situ monitoring, the sensor is necessary to be embedded in the structures. Fiber optic sensors can be embedded in the structures to get the health information in the structures. The fiber sensor was constructed with $3{\times}3$ fiber couplers to sense the multi-point strains and failure instants. The 4 RC (reinforced concrete) beams were made to 2 of A type, 2 of B type beams. These beams were reinforced by the reinforcing bars, and were tested under the flexural loading. The behavior of the beams was simultaneously measured by the fiber optic sensors, electrical strain gages, and LVDT. The states of the beams were interpreted by these all signals. By these experiments, There were verified that the fiber optic sensors could measure the structural strains and failure instants of the RC beams, The fiber sensors were well operated until the failure of the beams. It was shown that the strains of the reinforcing steel bar can be used to monitor the health condition of the beams through the flexural test of RC beams. On the other words, the results were arrived that the two strains in the reinforcing bar measured at the same point can give the information of the structural health status. Also, the failure instants of beams were well detected from the fiber optic filtered signals.

• Journal of the Optical Society of Korea
• /
• v.19 no.4
• /
• pp.376-381
• /
• 2015

Transmission characteristics of long-period fiber gratings (LPFGs) fabricated by periodically etching a conventional single-mode fiber (SMF) are investigated. After coating the SMF with photoresist, the cladding of the SMF is symmetrically and periodically removed by using a wet etching technique resulting in the formation of the LPFG. Tensile strain reinforces the coupling strength between the core and the cladding mode based on the photoelastic effect. The extinction ratio of the SMF-based LPFG at a wavelength of 1550.8 nm is measured to be -15.1 dB when the applied strain is $600{\mu}{\varepsilon}$. The ascent of ambient index shifts the resonant wavelength to shorter wavelength because of the increase of the effective refractive index of the cladding mode. The extinction ratio is diminished by increase in the ambient index because of the induction of the optical attenuation of the cladding mode. The transmission characteristics of the proposed LPFG with variations in torsion are also measured. The photoelastic effect based on torsion changes the extinction ratio and the resonant wavelength of the proposed SMF-based LPFG. The polarization-dependent loss of the LPFG is also increased by torsion because of the torsion-induced birefringence. The polarization-dependent loss of the LPFG at torsion of 8.5 rad/m is measured to be 3.9 dB.