• Journal of Korea Foundry Society
• /
• v.2 no.2
• /
• pp.2-9
• /
• 1982

This paper is concerned with the improvement of impact and tensile Properties of spheroidal graphite cast iron of the following duplex matricess which were heat treated in the eutectic transformation temperature range (that is, $({\alpha}+{\gamma})$ coexisting range) ; ferrite-martensite, ferrite-bainite and ferrite-pearlite. The absorbed energy and maximum load was measured by recording the load-deflection curve with instrumented Charpy impact testing machine in the temperature range from $+100^{\circ}C$ to $-196^{\circ}C$. It was found the ferrite-bainite duplex matrix showed the highest toughness among the above matrices in the room temperature and the low temperature range. Comparison of this matrix to ferrite-pearlite matrix(that is, as cast) showed a lowering of $27^{\circ}C$ in the nil-ductility transition temperature (NDT) and a lowering of $40^{\circ}C$ in the ductile-brittle transition temperature (TrE), Which seems to result from the finner dimple pattern observed using miorofractography.

• Journal of the Korean Society of Safety
• /
• v.18 no.3
• /
• pp.46-53
• /
• 2003

For the tensile tests of the F.E.M., microvoids are created by the boundary separation process at the martensite boundary or neighborhood and at inclusions within the fracture. to grow to the ductile dimple fracture. For the case of the M.E.F., microvoids created at the discontinuities of the martensite phase which exists at the grain boundary of the primary ferrite are grown to coalescence with the cleavage cracks induced at the interior of the ferrite, which as a result show the discontinuous brittle fracture behavior. In spite of their similar tensile strengths, the fatigue limit and the notch sensitivity of the M. E.F. is superior to those of the F.E.M., The M.E.F. is much more insensitive to notch than F.E.M. from the stress concentration factor($\alpha$).

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.28 no.4
• /
• pp.460-466
• /
• 2004

Cast austenitic stainless steel is used for several components, such as primary coolant piping, elbow, pump casing and valve bodies in light water reactors. These components are subject to thermal aging at the reactor operating temperature. Thermal aging results in spinodal decomposition of the delta-ferrite leading to increased strength and decreased toughness. This study shows that ferrite content can be predicted by use of the artificial neural network. The neural network has trained teaming data of chemical components and ferrite contents using backpropagation learning process. The predicted results of the ferrite content using trained neural network are in good agreement with experimental ones.

• Journal of the Korean Magnetics Society
• /
• v.5 no.5
• /
• pp.556-560
• /
• 1995

The absorption properties of Cu-Zn ferrite/rubber composite microwave absorbers with PZT(Lead Zirconate Titanate) additive were evaluated. The composite specimens have prepared by molding and curing the mixture of matrix rubber and Cu-Zn ferrite powders which are synthesized by the coprecipitation method using Fe Cl/sub 3/ .center dot. 6H/sub 2/O, CuCl/sub 2/ .center dot. 2H/sub 2/O and Zn Cl/sub 2/ as a starting raw materials. PZT is used as another filler particles to adjust the material constants of Cu-Zn ferrite/rubber composite specimens. We have found that the material constants of specimens could be controlled by various PZT mixing ratio. On the Cu-Zn ferrite/rubber composite specimens with PZT 10[wt%] additive, the reflection losses were larger than 30[dB] in the frequency range from 2.72 to 4.4[GHz]' by adjusing the thickness.

• Journal of Digital Convergence
• /
• v.12 no.8
• /
• pp.303-308
• /
• 2014

In this paper, a ferrite sheet at the back of the smartphone by type, pattern, stars, the thickness of the recognition distance by attaching the NFC optimum ferrite sheet simulation was designed. Characterized by patterns rather than the Full-type I-type communication distance of about 1 ~ 2mm more extended. Ferrite sheet metal by applying the NFC antenna is effective in improving the characteristics were confirmed. In the case of the pattern C, the permeability is 140, a thickness of 0.1mm, Full-type ferrite sheet when applied to NFC communication distance than normal electromagnetic absorber is increased from 45 to 59 was confirmed that.

• The Transactions of The Korean Institute of Electrical Engineers
• /
• v.60 no.12
• /
• pp.2270-2275
• /
• 2011

The sintering behavior and microwave properties of ferrite ($Ba_3Co_{2-2x}Zn_{2x}Fe_{24}O_{41}$ ceramics) were investigated for microwave applications. Also PIFA type antenna with ferrite was simulated. All samples were prepared by the solid state reaction method and sintered at $1350^{\circ}C$. All ceramics had relatively density above of 92% compare with theoretical density of $Ba_3Co_2Fe_{24}O_{41}$ ceramics. From the XRD pattens, the Z-type phase was existed as main phase in $Ba_3Co_{2-2x}Zn_{2x}Fe_{24}O_{41}$ ceramics. The permittivity and permeability of $Ba_3Co_{2-2x}Zn_{2x}Fe_{24}O_{41}$ ceramics were increased with Zn additions and decreased rapidly over frequency of 200~600 MHz. Several PIFA type antennas with ferrite and FR4 were simulated. All antenna structure had return loss of less than -10 dB at each resonant frequency. Simulated antenna using both ferrite and FR4 showed size reduction of 25% without a significant decrement of efficiency.

• The Proceeding of the Korean Institute of Electromagnetic Engineering and Science
• /
• v.4 no.2
• /
• pp.41-47
• /
• 1993

Electrical and electromagnetic wave absorbing properties of MnZn ferrite-rubber composites have been examined for varying the volume fraction of ferrite powder from 0.1 to 0.4 in the frequency range between 1-10 GHz. As the volume fraction of MnZn ferrite increased, the complex permittivity and permeability of composite increased. The peak of reflection loss at the frequency corresponding to 1/4 wavelength shifts to lower frequency, and shifts to lower frequency as the thickness of absorber increased. We show that for the ferrite-rubber composites the volume fraction of ferrite should be controled to obtain the absorbing properties required in given frequency range.

• Journal of Navigation and Port Research
• /
• v.28 no.6
• /
• pp.503-507
• /
• 2004

We prepared EM wave absorbers by using recycled Sr ferrite for GHz frequency, and investigated the effects of carbon additions and preparation temperatures on their EM wave absorption properties. A Sr ferrite EM wave absorber with the ratio of Sr ferrite: silicon rubber: carbon = 80 : 13.6: 6.4 wt% prepared at 7$0^{\circ}C$ showed -24 dB at 9.4 GHz and -23 dB at 5.5 GHz for 2 mm and 3 mm thickness, respectively.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.13 no.6
• /
• pp.545-550
• /
• 2000

In order to synthesize Ba-ferrite particles by molten salt method KCl and NaCl were added to basic composition to 50% by weight. X was varied from 0.0 to 1.0 to control the magnetic properties in $BaFe_{12-2x}$/ $Co_{x}$ / $Ti_{x}$ / $O_{19}$ and 1 mol% of $SiO_2$was added to control the aspect ratio of hexagonal platelets. And the effects of reaction temperatures were examined by varying the temperature from 85$0^{\circ}C$ to 120$0^{\circ}C$ with 5$0^{\circ}C$ intervals. Eutectic composition of NaCl and KCl lowered the crystallizing temperature of Ba-ferrite in molten salts than using KCl and NaCl separatly. The morphology of resulting Ba-ferrite particles was clearly hexagonal-shaped plates. $H_{c}$ and $M_{r}$ were decreased when F $e^{3+}$ was substitued with $Co^{2+}$ and $Ti^{4+}$ from x=0 to x=1.0 in $BaFe_{12-2x}$/ $Co_{x}$ / $Ti_{x}$ / $O_{19}$ . Adding 1mol% $SiO_2$in molten salt method increased the size but shortened c-axis of the hexagonal ferrites and this result is an opposite phenomenon compared with the result in solid-statge reaction.n.ion.n.

• Resources Recycling
• /
• v.12 no.6
• /
• pp.32-37
• /
• 2003

For the reduction of electromagnetic biological effects from cellular phones, the electrical field radiation from cellular phone antenna is reduced by using partial ferrite material added on the phone case as ground plane. On the given properties (permittivity, permeability and conductivity) of ferrite material, the characteristics of monopole antenna is analysed depending on the variation of ferrite added configuration(thickness and shape). According to this analysis, the design method and direction to minimize the biological effects to human head is proposed in 1.7 GHz band PCS phones. For the exact analysis involving the permittivity, per-meability and conductivity of ferrite material, FDTD numerical method is used.