• Membrane and Water Treatment
• /
• 제9권1호
• /
• pp.9-15
• /
• 2018

Coagulation process using aluminum sulfate ($Al_2(SO_4)_3$) and ferric chloride ($FeCl_3$) was employed as a treatment method for decolorization of a synthetic textile wastewater containing red dye in this paper. Factors such as initial pH, coagulant dosage, initial concentration, conductivity and mixing conditions that influence color removal efficiency were experimentally tested. It was found that $Al_2(SO_4)_3$ is more efficient than $FeCl_3$ as coagulant. When $40mgL^{-1}$ aluminum sulfate was used, results showed that color induced by the red dye was efficiently removed (> 90 %) and was obtained in a large range of initial pH from 4 to 8 with, and for a dye concentration lower than $235mg\;L^{-1}$. After addition of the coagulant, the medium had to be mixed for 30 min at 60 rpm, then allowed to settle for 40 min. The effects of water conductivity in the range $0.035-2.42mS\;cm^{-1}$ and dye concentration up to $380mg\;L^{-1}$ were also followed and discussed.

• 한국지하수토양환경학회:학술대회논문집
• /
• 한국지하수토양환경학회 2003년도 추계학술발표회
• /
• pp.368-371
• /
• 2003

Accidental release of petroleum products from underground storage tank(USTs) is one of the most common causes of groundwater contamination. BTEX is the major components of fuel oils, which are hazardous substances regulated by many nations. In addition to BTEX, other gasoline consituents such as MTBE(methyl-t-buthyl ether), anphthalene are also toxic to humans. Natual attenuation processes include physic, chemical, and biological trasformation. Aerobic and anaerobic biodegradation are believed to be the major processes that account for both containment of the petroleum-hydrocarbon plum and reduction of the contaminant concentrations. Aerobic bioremediation has been highly effective in the remediation of many fuel releases. However, Bioremediation of aromatic hydrocarbons in groundwater and sediments is ofen limited by the inability to provide sufficient oxygen to the contaminated zones due to the low water solubility of oxygen. Anaerobic processes refer to a variety of biodegradation mechanisms that use nitrate, ferric iron, sulfate, and carbon dioxide as terminal electron accepters. The objectives of this study was to conduct laboratory-scale microcosm studies in assessing enhanced bioremediation potential of BTEX and MTBE under various electron accepters(aerobic, nitrate, ferric iron, sulfate) in contaminated Soil. these results suggest that, presents evidence and a variety pattern of the biological removal of aromatic compounds under enhanced nitrate-, Fe(III)-, sulfate-reducing conditions.

• 한국염색가공학회지
• /
• 제12권2호
• /
• pp.96-102
• /
• 2000

For the effective treatment of dyeing-complex wastewater, the most effective chemical coagulation method was studied. For the chemical coagulation of dyeing-complex wastewater, polyferric sulfate, $4Al_2(SO_4)_3$, PAC, ferrous sulfate, ferric sulfate, $FeCl_2$ and lime were used. It was investigated that polyferric sulfate was the most efficient coagulant. The optimal conditions and results for polyferric sulfate include the followings. When initial $COD_{Mn}$ concentration was 600mg/L, the optimal initial pH, dosage of coagulant, dosage of lime and PAA for $COD_{Mn}$ removal efficiency were 5, 1,200mg/L, 500mg/L and lmg/L, respectively. The optimal dosage of polyferric sulfate was increased proportionally to the influent $COD_{Mn}$ concentration.

• 한국화재소방학회:학술대회논문집
• /
• 한국화재소방학회 2001년도 추계학술대회 논문집
• /
• pp.301-310
• /
• 2001

본 연구는 내화성능을 가진 수막보호유리벽을 실제 건축물에 적용하는데 있어서 필수적으로 고려해야 할 가상시나리오 중에서 수막이 유리면을 보호하기 이전에 유리면에 근접되어 있는 화염으로부터 방출되는 복사열이 유리면이 가열된 상태에서 수막이 형성될 경우 유리면의 온도가 급속히 냉각됨으로서 발생할 수 있는 급냉파열특성을 규명하기 위해 실험한 연구로서 가열면온도범위에 따라 유리면에$150^{\circ}C$이상 $250^{\circ}C$이하에서 수막이 형성될 경우 급냉파열은 일어나지 않았으나 일반유리는 $100^{\circ}C$이상 $150^{\circ}C$이하에서 급냉파열이 일어남을 확인하였다. 즉 방화구획벽에 적용가능한 수막형성유리벽의 유리가 강화유리인점을 착안하면 수막의 도포이전에 강화유리면의 온도가 $250^{\circ}C$까지 올라가기 전에는 수막을 유리면에 접촉하여도 유리면의 급냉파열이 일어나짐 않음을 확인할 수 있었다. 이점은 일정한 구획내에서 유리면의 직근에 설치된 감지기에 의해 수막형성시스템의 가동을 할 경우 급내파열형상이 발생하지 않는 온도범위를 설정할 때 중요한 데이터로 활용가능하다. 결과적으로 국부복사열에 의하여 온도범위를 설정할 때 중요한 데이터로 활용가능하다. 결과적으로 국부복사열에 의하여 유리면의 온도가 급냉파열현상을 일으키는 한계온도에 이르기 전에 유리벽체 상부의감지기의 작동이 필수적으로 일어날 수 있음을 증명한다면 수막을 이용한 유리벽체를 일정시간이상의 내화성능이 요구되는 방화구획의 수직부재로 활용하는데 있어서 걸림돌이 되는 급냉파열에 대한 우려를 종식시키는데 이바지할 수 있다.l류 11.56%, acid류 38.87%, hydrocarbon류 2.89%, ester류 0.80%, 총 70.32%가 확인되었다. Alcohol류에서 linalool가 3.78%, acid류에서는 caproic acid류가 14.40%, carbonyl류에서 2-hydroxy-4-methoxyacetophenone이 2.99%, hydrocabon류에서는 aromadendrene가1.59% 그리고 ester류에서는 methyl palmitate가 0.43%으로 가장 많이 함유하고 있었다.0ppm에서 약 25.6%흡수되었고 ferric citrate 100ppm은 24.7%, ferrous sulfate는 19.7%흡수되었다. ILC를 첨가하지 않은 100ppm 철분염 용액은 ferrous sulfate를 제외하고는 흡수도가 감소되었다. 철분 결핍된 쥐에게 gavage 방법에 의하여 철분강화우유를 투여하였을 때 철분 25ppm 시료에서는 ferrous sulfate가 12.5%로 가장 높았고 ferrous lactate는 8.1%, ferric citrate는 6.5% 흡수되었다. 철분 100ppm수준에서는 흡수율이 낮아져 ferrous sulfate는 25ppm 시료보다 절반이하 수준이었다. Ferric citrate는 차이가 거의 없었으며 ferrous lactate는 70%수준이었다. 이상의 결과에서 철분강화우유에 사용하기 적합한 철분염은 ferrous lactate, ferric citrate였는데 특히 ferrous lactate는 제품의 이화학적 품질, 생이용성 측면 모두에서 가장 좋은 것으로 나타났다.다 높았으며, 1회당 평균 8.1$\pm$5.1개의 난포란을 회수하였다.

• Restorative Dentistry and Endodontics
• /
• 제18권2호
• /
• pp.423-430
• /
• 1993

The purpose of this study was to investigate the effect of ferric and ferric ions contained in phosphoric acid solution as a pretreatment solution on bonding of MMA/TBBO resin to dentin. Each of 1 % and 3 % ferric chloride. cupric chloride. cupric sulfate. and cupric nitrate was mixed into 10% phosphoric acid solution and pretreated dentin surface of bovine anterior teeth for 30 seconds followed- by water rinse and dry. Tensile bond strength was determined after bonding of pretreated dentin with MMA/TBBO resin by use of brush-on ;technique and storing for 24 hours in 3it distilled water. The amount of cupric ions adsorbed on pretreated dentin surface was detected by Wave-Dispersion X-ray microanalyzer for different groups of each pretreatment solution containing cupric salts. The pretreatment with cupric ions contained in 10% phosphoric acid solution was effective to increase bonding strength of MMA/TBBO resin to dentin but not in case of ferric ions. The pretreatment with 3 % cupric chloride and cupric nitrate both enhanced significant increase in bonding strength compared to the control group of 10% phosphoric acid solution(p<0.05). Cupric ions measured in pretreated dentin surface was higher in 3 % cupric chloride group than in 1% cupric chloride group, but couldn't find distinct relationship from the results of this experiment between the amount of adsorbed cupric ions according to the kind of cupric salts and the bonding strength value.

• 한국식품조리과학회지
• /
• 제20권2호
• /
• pp.119-125
• /
• 2004

Mixograph를 이용하여 반죽의 물성에 미치는 화학첨가제의 영향을 조사한 결과 ammonium ferric citrate와 ferric sulfate는 0.1% 수준에서는 밀가루 반죽의 탄성에 뚜렷한 영향을 미치지 않았으나, MgSO$_4$, CaCl$_2$ 및 ZnO는 반죽의 탄성을 증가시키며 최적반죽시간을 연장시켜 반죽 시간이 길어졌다. 그러나 Ca과 Mg을 각각 갖는 calcium citrate와 MgCl$_2$는 반죽 시간이나 탄성에 뚜렷한 영향을 나타내지 않았다. 빵의 부피에 미치는 영향은 0.1% MgSO$_4$와 CaCl$_2$가 브롬산 칼륨을 전혀 첨가하지 않은 대조구보다 부피 팽창이 더 커져서 브롬산 칼륨과 같은 팽창제로서의 기능을 확인하였으며, 이들을 첨가한 빵의 속과 겉껍질의 색은 모두 대조구보다 더 밝아서 첨가한 화학첨가제들이 빵의 색을 밝게 하는 것을 확인할 수 있었다. 밀가루의 내재된 효소를 불활성화 시키기 위하여 볶음처리와 UV 및 microwave 조사된 밀가루는 최적 반죽시간을 초과하여 계속 반죽하여도 최적반죽시간 후 반죽의 탄성저하현상이 처리하지 않은 대조구에 비하여 감소되어 반죽의 안정성이 향상되었으나, 열처리한 밀가루로 제조한 빵은 부피가 대조구에 비하여 적었으므로 열처리는 반죽의 안정성은 향상시킬 수는 있으나 빵의 부피 증가에는 효과적이지 못하였다.

• 한국환경과학회지
• /
• 제19권8호
• /
• pp.931-940
• /
• 2010

The Raw water from Deer Creek (DC) reservoir and Little Cottonwood Creek (LCC) reservoir in the Utah, USA were collected for jar test experiments. This study examined the removal of arsenic and turbidity by means of coagulation and flocculation processes using of aluminum sulfate and ferric chloride as coagulants for 13 jar tests. The jar tests were performed to determine the optimal pH range, alum concentration, ferric chloride concentration and polymer concentration for arsenic and turbidity removal. The results showed that a comparison was made between alum and ferric chloride as coagulant. Removal efficiency of arsenic and turbidity for alum (16 mg/L) of up to 79.6% and 90.3% at pH 6.5 respectively were observed. Removal efficiency of arsenic and turbidity for ferric chloride (8 mg/L) of up to 59.5% at pH 8 and 90.6% at pH 8 respectively were observed. Optimum arsenic and turbidity removal for alum dosages were achieved with a 25 mg/L and 16 mg/L respectively. Optimum arsenic and turbidity removal for ferric chloride dosages were achieved with a 20 mg/Land 8 mg/L respectively. In terms of minimizing the arsenic and turbidity levels, the optimum pH ranges were 6.5 and 8for alum and ferric chloride respectively. When a dosage of 2 mg/L of potassium permanganate and 8 mg/L of ferric chloride were employed, potassium permanganate can improve arsenic removal, but not turbidity removal.

• 한국미생물·생명공학회지
• /
• 제31권2호
• /
• pp.197-200
• /
• 2003

In oil-contaminated environments, anaerobic biodegradation of toluene depended on the concentration and distribution of terminal electron acceptor as well as the physicochemical properties such as DO concentration, redox potential and pH. This study showed the anaerobic biodegradation of toluene in two different soils by using nitrate reduction, ferric iron reduction, sulfate reduction and methanogensis. Toluene degradation rates in the soil samples taken from rice filed and tidal mud flat by nitrate reduction were higher than those by other processes. Tho soil samples from the two fields were enriched for 130 days by providing toluene as a sole carbon source and nitrate or sulfate as a terminal electron acceptor. The toluene degradation rates in the enriched denitrifying consortia obtained from the rice field and tidal mud flat soil were 310.7 and 200.6 $\mu$mol$ L^{-1}$ / $d^{-1}$, respectively. The toluene (legradation rates in the enriched sulfate-reducing consortia from the fields ranged fi-om 149.1 to 86.1$\mu$mol $L^{-1}$ / $d^{-1}$ .

• Geomechanics and Engineering
• /
• 제33권2호
• /
• pp.121-131
• /
• 2023

Clay sedimentation has been widely analyzed for its application in a variety of geotechnical constructions such as mine tailing, artificial islands, dredging, and reclamation. Chemical flocculants such as aluminum sulfate (Al₂(SO₄)₃), ferric chloride (FeCl₃), and ferric sulfate (Fe(SO₄)₃), have been adopted to accelerate the settling behaviors of clays. As an alternative clay flocculant with natural origin, this study investigated the settling of xanthan gum-treated kaolinite suspension in deionized water. The sedimentation of kaolinite in solutions of xanthan gum biopolymer (0%, 0.1%, 0.5%, 1.0%, and 2.0% in a clay mass) was measured until the sediment height was stabilized. Kaolinite was aggregated by xanthan gum via a direct electrical interaction between the negatively charged xanthan gum molecules and positively charged edge surface and via hydrogen bonding with kaolinite particles. The results revealed that the xanthan gum initially bound kaolinite aggregates, thereby forming larger floc sizes. Owing to their greater floc size, the aggregated kaolinite flocs induced by xanthan gum settled faster than the untreated kaolinite. Additionally, X-ray computed tomography images collected at various depths from the bottom demonstrated that the xanthan gum-induced aggregation resulted in denser sediment deposition. The findings of this study could inspire further efforts to accelerate the settling of kaolinite clays by adding xanthan gum.

• 한국미생물·생명공학회지
• /
• 제18권6호
• /
• pp.553-559
• /
• 1990

많은 관심이 집중되고 있는 환경오염의 대처방안의 일환으로, plastic 및 wrap 제조시 가소제로 가장 널리 사용되고 폐수 중에 대량 유출되어 인체에 유독한 난분해성 고분자 유기합성 물질로서 문제가 되고 있는 phthalate ester의 일종인 dibutyl phthalate(DBP)를 분해 자화할 수 있는 미생물을 분리하고자 했다. 저자들은 대구 근교의 토양 및 sludge에서 DBP 분해 관련 효소인 protocatechuate dioxygenase을 생성하는 새로운 균주를 분리하여 동정하였다.