• 한국정밀공학회지
• /
• 제19권3호
• /
• pp.123-130
• /
• 2002

Linear motors can drive a linear motion without intermediate gears, screws or crank shafts. Linear motors can successfully replace ball lead screw in machine tools because they have a high velocity, acceleration and good positioning accuracy. On the other hand, linear motors emit large amounts of heat and have low efficiency. In this paper, heat sources of a synchronous linear motor with high velocity and force measured and analyzed. To improve the thermal characteristics of the linear motor, an insulation layer with low thermal conductivity is inserted between cooler and machine table. Some effects of the insulation layer are presented.

• 천문학회보
• /
• 제35권2호
• /
• pp.68.2-68.2
• /
• 2010

Diffuse interstellar atomic hydrogen (HI) gases are easily shaped into shell-like features by energetic processes such as stellar winds and supernova explosions. The physical characteristics and the Galactic distribution of HI shells and shell-like structures, therefore, are closely related to those of the energy sources. Recently, Inner-Galaxy Arecibo L-band Feed Array (I-GALFA) low-latitude HI survey has been completed. I-GALFA HI survey covers the central part of the first quadrant ($31^{\circ}{\lesssim}1{\lesssim}77^{\circ}$ at b = $0^{\circ}$, ${\mid}b{\mid}\lesssim\;12^{\circ}$) with spatial and velocity resolutions of 3.35′and 0.184 km/s, respectively. The high-angular and high-velocity resolutions enable in-depth investigation of HI shells including the ones of smaller angular sizes. We have found 36 shell candidates with the naked eye. Their angular sizes are distributed from $\sim0.4^{\circ}$ to $\sim12^{\circ}$. About sixteen of them appear to be expanding. We examine associated features at other wavebands and discuss their origin.

• 한국해양공학회:학술대회논문집
• /
• 한국해양공학회 2006년 창립20주년기념 정기학술대회 및 국제워크샵
• /
• pp.416-419
• /
• 2006

Numerical analysis is carried out to identify the wall thinning effect inside the feed water valve. The finite volume method is applied to make analysis for the viscous flows. The commercial cock FLUENT is used for the simulation and the GAMBIT for the grid generation. The RNG $\kappa-\varepsilon$ model is used for the turbulence and the tet-hybrid grid is applied for the modeling. The velocity vector, the pressure contour, the change of residual along the iteration number, and the dynamic head are predicted for the hydrodynamic investigation.

• 한국공작기계학회:학술대회논문집
• /
• 한국공작기계학회 2000년도 춘계학술대회논문집 - 한국공작기계학회
• /
• pp.121-126
• /
• 2000

This research proposes a new advanced control method and demonstrates its realization in part. By incorporating shape machining and cutting force control at a time, this integrated scheme makes it possible to machine a desired shape and avoid the trouble of programming feedrate and spindle speed before machining and also reduce the shape error. The main idea proposed to achieve those goals consists in giving commanded path and desired cutting force at the same time. which makes it possible for position and force controller to distribute the corresponding velocity of individual axes and main spindle by an appropriate interpolation. That indicates we can replace the built-in interpolator of commercial machine tools by the developed algorithm.

• 한국레이저가공학회지
• /
• 제3권3호
• /
• pp.21-29
• /
• 2000

For the direct metal shape processing the powder feed device which is different from the widely used in rapid prototyping. is developed, The three dimensional object is shaped with the melting metal powder. The developed research has applied to rapid prototyping in ultraprecision for MEMS and medical science fields required of rapid manufacture of complex shape. The goal of this study make 3D model which has precision accuracy. Powder spreading apparatus has been more improved because that the control of powder spread is very important in layer manufacturing. It consists of the vibration motor, nozzle and tube which supplies various metal powder. This apparatus could control the spreading velocity that could control powder spreading thickness. Laser on/off switch was adapted because laser scanning velocity must be preserved constantly to prevent heat transformation of laser overheating. The error between sintered thickness md experimental one occurred by shrinkage in sintering melting process. The problem of heat transformation was solved by On/Off switching system.

• 한국기계가공학회지
• /
• 제10권6호
• /
• pp.46-49
• /
• 2011

The grinding is a popular process for studying constant velocity joint and process in automobile industry. In this study, The study gives the data of wheel type and grinding of inner race is developed. As a result I obtained the data of grinding conditions makes good surface roughness get a grinding conditions. The grinding characteristics and conditions of inner race were investigated with respect to grinding feed, cutting depth, grinding time. The results were suddenly increased and the detailed surfaces were extremely obtained. Grinding condition was big more affected by grinding time, grinding speed and grinding depth.

• Journal of the Korean Wood Science and Technology
• /
• 제49권4호
• /
• pp.328-335
• /
• 2021

Considerable differences exist in the characteristics of size reduction and classification because of biomass species. Miscanthus sacchariflorus (M. sacchariflorus) Goedae-Uksae 1 is not used efficiently because of the imperfections of the processing technology for this biomass. Therefore, for the best use of specific biomass, improvement in the feedstock preparation of the biomass for processing, such as pellet manufacturing, is necessary. In this study, a laboratory-scale cone grinder and air classifier were designed and combined to investigate the performance of the combination system for M. sacchariflorus. The average equivalent spherical diameter of particles showed a close relationship with air velocity for air classification. The air velocity range to classify proper particles for pelletization was determined to be 6.0-6.8 m/s. The mass ratios of the collected particles to feed mass for four lengths of chopped M. sacchariflorus were 45.1%:46.1%, 39.1%:46.6%, and 44.1%:52.8% at the first, second, and third steps in simulating the multistep combination system, respectively.

• Journal of Biosystems Engineering
• /
• 제7권1호
• /
• pp.33-41
• /
• 1982

When wet-paddy is threshed by conventional auto-fed thresher, the threshed material under the concave is difficult to separate with pneumatic separation only. The development of thresher with an oscillating sieve in addition to the conventional pneumatic separation has been recommanded to improve the separation of grains from straw and chaff having high moisture content. This study was intended to evaluate the separating performance of an oscillating sieve and to obtain the effective operation conditions of the sieve separation. The sieve with oscillating in an elliptical motion was developed and installed in the experimental unit which can simulate the separating operation of the conventional auto-fed thresher. Results of the study are summarized as follows: 1. The flowing velocity of grains on oscillating sieve was increased as the sieve frequency increased but the feed rate did not significantly affect the flowing velocity of grains on sieve. 2. The effects of sieve frequency and the direction of sieve rotation on the separating performance by oscillating sieve show that increasing the frequency of sieve driving crank above the 460 rpm in the same direction of material flow (con-flow) improved the separating performance. 3. The height of grain guide plate and air velocity through the sieve to optimize the separating performance of oscillating sieve were experimentally determined to give about 10cm above the sieve and 7 m/s, respectively.

• International Journal of Control, Automation, and Systems
• /
• 제1권4호
• /
• pp.474-483
• /
• 2003

Belt drives provide freedom to position the motor relative to the load and this phenomenon enables reduction of the robot arm inertia. It also facilitates quick response when employed in robotics. Unfortunately, the flexible dynamics deteriorates the positioning accuracy. Therefore, there exists a trade-off between the simplicity of the control strategy to reject time varying disturbance caused by flexibility of the belt and precision in performance. Resonance of the system further leads to vibrations and poor accuracy in positioning. In this paper, accurate positioning of a belt driven mechanism using a feed-forward compensator under maximum acceleration and velocity constraints is proposed. The proposed method plans the desired trajectory and modifies it to compensate delay dynamics and vibration. Being an offline method, the proposed method could be easily and effectively adopted to the existing systems without any modification of the hardware setup. The effectiveness of the proposed method was proven by experiments carried out with an actual belt driven system. The accuracy of the simulation study based on numerical methods was also verified with the analytical solutions derived.

• Advances in materials Research
• /
• 제9권3호
• /
• pp.189-202
• /
• 2020

The objective of the present work is to investigate the effect of cutting parameters (Vc, fz and ap) on tool life and the level of vibrations velocity in the machined part during face milling operation of hardened AISI 52100 steel. Dry-face milling has been achieved in the annealed (28 HRc) and quenched (55 HRc) conditions using multi-layer coating micro-grain carbide inserts. Statistical analysis based on the Response surface methodology (RSM) and ANOVA analysis have been conducted through a plan of experiments methodology using a reduced Taguchi table (L9) in order to obtain engineering models for tool life and vibration velocity in the workpiece for both heat treatment conditions. The results show that the cutting speed has a dominant influence on tool life for both soft and hard part. Cutting speed and feed per tooth is the most significant parameters for vibration levels. Comparing the experimental values with those predicted by the developed engineering models of tool life and levels of vibrations velocity, a good correlation has been obtained (between 97% and 99%) in annealed and hard conditions.