• Transactions of the Korean Society of Mechanical Engineers
• /
• v.8 no.6
• /
• pp.553-563
• /
• 1984

Heat transfer modeling was performed in order to study a natural solar heating system. Simulation of the system was obtained by writing instantaneous energy balance equations for the various components. A thermal-network provided the means for systematically accounting for each of the energy balances. The resulting balances were solved using time varying inputs, such as solar gain and ambient temperature, and the initial temperatures of the components. Parametric heat transfer calculations were performed. Results are discussed which illustrate several effects, including variation of thermal capacity of the storage wall, installation of night insulation, installation of a thermally controlled fan between the sunspace and room, and variation of the width of the sunspace.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2002.05a
• /
• pp.778-784
• /
• 2002

FFU are used increasingly by the microeleceronics industry to provide clean recirculating air for the fabrication of integrated circuits and laminar flow air. There may be several hundred ffu in a large cleanroom, covering 100% of the ceiling area. Hence, there is of often knowledge in the inside and outside of the country the flu give rise to noise & vibration trouble to microelectronics industry. Noise ＆ Vibration control for satisfication about noise ＆ vibration criteria in TFT-LCD factory cleanroom be in need of exact noise & vibration data of accurence from utility & equipment that can be exert a bad influence upon cleanroom. In this pater, hence we found out noise and vibration properities of ffu by using experimental method. And, we performed noise ＆ vibration analysis about noise it vibration level in cleanroom using semiempirical method for quantative approach about noise ＆ vibration level in cleanroom.

• Fire Science and Engineering
• /
• v.32 no.4
• /
• pp.69-74
• /
• 2018

This study developed a ventilation damper that can control flow rate according to pressure differential variation of the smoke control room in order to improve problems related to existing smoke management systems and maximizing performance of smoke management systems. The development damper was tested for verification of utility and performance. The supply flow of the developed ventilation damper was increased by about 1 to 5%. The results prove the effectiveness of the flow control ventilation damper by providing stable flow over the designed flow of the fan in the smoke control room. In addition, the study acquired the original technology for a flow control ventilation damper.

• Korean Journal of Air-Conditioning and Refrigeration Engineering
• /
• v.1 no.2
• /
• pp.116-127
• /
• 1989

Research on reheating cooling cycle and its practical application have been made to prevent unequalized distribution of temperature and humidity of room due to lack of supply air volume and dewdrops on supply diffusers to be taken place as a result of lower temperature of supply air than that of dew point of room air in cooling cycle of constant air volume, single duct, single zone and draw-through fan type. In view of the fact that human body is insensitive to humidity, it is possible not only to construct the complete non-reheating cooling cycle by increasing the humidity point allowable with the deduction of occupant's sense of pleasantness minimizing, but also to get cooling cycle decreasing the reheating quantity if the humidity exceeds the point allowable. In addition, it is possible to save maximum 8% in electric energy for cooling in cooling system by constructing non-reheating cooling cycle instead of reheating cooling cycle and by increasing the relative humidity of room from 50% to 65% in case efficiency and air pressure of cooling system are low. It is also possible to get an optimum cooling cycle by determining the room humidity in consideration of pleasantness of occupants and conservation rate of electric energy if the cooling capacity, efficiency and total pressure of cooling equipment are fixed.

• Journal of the Korean Institute of Gas
• /
• v.16 no.2
• /
• pp.31-37
• /
• 2012

This paper describes to analyze the ventilation performance of a room air conditioner for indoor comfort control. An experimental apparatus consists of a test room, the room air conditioner, a tracer gas measurement system, a supply fan and a controller. Ventilation performance as a function of human occupancy is evaluated with supply ventilation air using a tracer gas technique of CO2 gas in the test room. The ventilation performance is evaluated in a step-down method based on ASTM Standard E741-83 and is found to increase with increasing supply ventilation rate. The CO2 gas concentration is decayed rapidly without human occupancy. The ventilation performance without human occupancy increases up to 55% and the ventilation performance with one person increases up to 25% at the supply air of 570 lpm comparing with a natural reduction after one hour. A modeling for ventilation performance of a room air conditioner in a test room is presented using experimental datum.

• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.37 no.7
• /
• pp.709-716
• /
• 2013

A fan filter unit (FFU) is a device which supplies clean air from the ceiling in a clean room. With an increase in its size, velocity variation occurs within the exhaust plane and this damage the product quality or productivity. Hence, a guide vane is installed inside the device to enhance the velocity uniformity. Because the vane reduces the flow rate for a given pumping power, an optimum design is required to achieve velocity uniformity while minimizing the flow rate reduction at the same time. To find a geometry that satisfies these requirements, a series of numerical simulations has been conducted while changing the angle and length of the guide vanes. By changing the geometry of the side guide vane, the velocity uniformity increased by 3.7% and the flow rate decreased by 1.5%. For the center guide vane, the velocity uniformity increased by 2.9% and the flow rate decreased by 0.7%.

• Proceedings of the SAREK Conference
• /
• 2006.11a
• /
• pp.19-19
• /
• 2006

• Proceedings of the Korean Society of Marine Engineers Conference
• /
• 2006.06a
• /
• pp.157-162
• /
• 2006

INERGEN 의 성능시험으로서 가장 확실한 방법은 직접적인 전량 방출시험이 최선의 방법이나 고비용, 안전문제 및 시험절차의 난이성 등의 이유로 NFPA 2001 이나 선급에서는 직접적인 방출 시험을 가급적 규제하고 있다. 지금까지는 이론적 계산을 통한 서류제출로 대체하거나, 간접 시험방법인 Door Fan Test 를 통하여 소화설비의 적정성을 평가하는 것이 보편적이었다. 하지만 이번 WOODSIDE 선주사의 전례없는 요구로 SHI 에서는 전량 방출시험을 I,G.G. Room 에 대해 수행하게 되었다. 본 자료에서는 조선설게자 관점에서 Full scale test 를 통한 Inergen 성능시험 최적화 방법을 제시하고자 한다.

• Proceedings of the SAREK Conference
• /
• 2005.06a
• /
• pp.140-140
• /
• 2005

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 1995.10a
• /
• pp.136-141
• /
• 1995

Room Air Conditioner(이하 RAC) 실내기는 열교환기, Cross Flow Fan(이하 CFF), 곡률, Stabilizer(이하 STB) 등 여러 설계인자가 소음, 풍량 및 압력 등에 상호 복합적으로 연성(Coupled)되어 있어 각 인자가 성능에 미치는 영향을 정량적으로 밝혀 내기가 쉽지 않다. 따라서 RAC 실내기의 고성능 및 저소음화를 실현하기 위해서는 실내기를 구성하는 각 인자간의 상호 관련성 및 각 인자가 소음.성능 등에 미치는 영향을 체계적으로 분석하는 것이 필수적이다. 본 연구에서는 설계인자중 소음 및 풍량에 민감한 영향을 주는 STB 위치 및 형상 등에 관하여 자세히 다루고자 한다. STB위치의 적절한 범위를 설정하기 위해 Laser Doppler Velicitimeter(이하 LDV)를 이용하여 곡률별 실내기 내부의 유속분포 및 속도 벡터를 측정하였고, CFF내부 Vortex의 정확한 위치를 찾아냈다. 또한 실내기 저소음화를 위한 소음원 규명 측면에서 실내기 내부의 난류도와 관련하여 속도 Fluctuation을 정의하고, 실험을 통해 구하였다.