• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.41 no.7
• /
• pp.516-523
• /
• 2013

The tip clearance effect on counter-rotating ducted fan of VTOL UAV in hovering condition, was investigate using computational analysis. The $k-{\omega}$ SST turbulence model is employed in this study. The numerical results of baseline model are validated by wind tunnel test in hovering and forward conditions. It is observed that if tip clearance of one rotor in the counter-rotating ducted fan increase then the thrust coefficient of another rotor increases. In Addition to this, when the tip clearance of the rear rotor increases, the thrust of the ducted fan is improved due to increasing of average total pressure at exit plane.

• International Journal of Fluid Machinery and Systems
• /
• v.5 no.2
• /
• pp.65-71
• /
• 2012

The objective of the present investigation is to explore the possibility of improving the performance of a centrifugal fan at low Reynolds numbers using a simple passive means, namely Gurney flap (GF). GFs of 1/$8^{th}$ inch brass angle (3.175 mm) corresponding to 15.9% of blade exit height or 5.1% of blade spacing at the impeller tip are attached to the impeller blade tip on the pressure surface. Performance tests are carried out on the centrifugal fan with vaneless diffuser at five Reynolds numbers (viz., 0.30, 0.41, 0.55, 0.69, $0.82{\times}10^5$, i.e., at five speeds respectively at 1,100, 1,500, 2,000, 2,500 and 3,000 rpm) without and with GF. Static pressures on the vaneless diffuser hub and shroud are also measured for each speed at four flow coefficients [${\phi}$=0.23 (below design flow coefficient), ${\phi}$=0.34 (design flow coefficient), ${\phi}$=0.45 (above design flow coefficient) and ${\phi}$=0.60 (above design flow coefficient)] with and without GF. From the performance curves it is found that the performance of the fan improves considerably with GFs at lower Reynolds numbers and improves marginally at higher Reynolds number. Similar improvements are observed for the static pressures on the diffuser hub and shroud. The effect of Reynolds number on the performance and static pressures is considerable. However the effect is reduced with GFs.

• Composites Research
• /
• v.34 no.6
• /
• pp.337-344
• /
• 2021

In this study, the progressive failure behavior of the composite fan blade dovetail element under tensile loading is numerically investigated through finite element(FE) simulation. The accuracy of prediction by FE simulation is verified through tensile testing. The dovetail element is one of the joints for coupling the fan blade with the disk in a turbofan engine. The dovetail element is usually made of a metal material such as titanium, but the application of composite material is being studied for weight reduction reasons. However, manufacturing defects such as drop-off ply and resin pocket inevitably occur in realizing complex shapes of the fan blade made by composite materials. To investigate the effect of these manufacturing defects on the composite fan blade dovetail element, we performed numerical simulation with FE model to compare the prediction of the FE model and the tensile test results. At this time, the cohesive zone model is used to simulate the delamination behavior. Finally, we found that FE simulation results agree with test results when considering thermal residual stress and through-thickness compression enhancement effect.

• Tunnel and Underground Space
• /
• v.24 no.6
• /
• pp.464-472
• /
• 2014

In large-opening room-and-pillar mining sites, particularly without the devices for the ventilation control, the airflow pattern created by the local fan operation is too complicated to quantify and also shows low ventilation efficiency. This study aims at performing a series of CFD analysis for the so-called venturi effects of the local fans; the effects of increasing airflow rate along the axis downstream of fan resulting from increased kinetic energy and subsequently decreased static pressure in the downstream. Effects of the fan type and installation height are compared. 1 vane-axial fan and 2 propeller fans are analyzed for their venturi effects, while the vane-axial fan was installed at the height of 1.0, 1.5 and 2.0m for comparison. The results can be applied to improve the economy and efficiency of local fans for securing better air quality and work environment management.

• Journal of Mechanical Science and Technology
• /
• v.18 no.2
• /
• pp.185-192
• /
• 2004

The aeroacoustic characteristics of a centrifugal fan for a vacuum cleaner and its noise reduction method are studied in this paper. The major noise source of a vacuum cleaner is the centrifugal fan. The impeller of the fan rotates at over 30000 rpm, and generates very high-level noise. It was revealed that the dominant noise source is the aerodynamic interaction between the rotating impeller and stationary diffuser. The directivity of acoustic pressure showed that most of the noise propagates backward direction of the fan-motor assembly. In order to reduce the high tonal sound generated from the aerodynamic interaction, unevenly pitched impeller and diffuser, and tapered impeller designs were proposed and experiments were performed. Uneven pitch design of the impeller changes the sound quality while the overall sound power level (SPL) and the performance remains similar. The effect of the tapered design of impeller was evaluated. The trailing edge of the tapered fan is inclined. This reduces the flow interaction between the rotating impeller and the stationary diffuser because of some phase shifts. The static efficiency of the new impeller design is slightly lower than the previous design. However, the overall SPL is reduced by about 4 dB(A). The SPL of the fundamental blade passing frequency (BPF) is reduced by about 6 dB (A) and the 2$\^$nd/ BPF is reduced about 20 dB (A). The vacuum cleaner with the tapered impeller design produces lower noise level than the previous one, and the strong tonal sound was dramatically reduced.

• International Journal of Fluid Machinery and Systems
• /
• v.2 no.2
• /
• pp.110-120
• /
• 2009

Generally the fluid flows within the centrifugal impeller passage as a decelerating flow with an adverse pressure gradient along the stream wise path. This flow tends to be in a state of instability with flow separation zones on the suction surface and on the front shroud. Hence several experimental attempts were earlier made to assess the efficacy of using boundary layer fences to trip the flow in the regions of separation and to make the flow align itself into stream wise direction so that the losses could be minimized and overall efficiency of the diffusion process in the fan could be increased. With the development of CFD, an extensive numerical whole field analysis of the effect of boundary layer fences in discrete regions of suspected separation points is possible. But it is found from the literature that there have been no significant attempts to use this tool to explore numerically the utility of the fences on the flow field. This paper attempts to explore the effect of boundary layer fences corresponding to various geometrical configurations on the impeller as well as on the diffuser. It is shown from the analysis that the fences located on the impellers near the trailing edge on pressure side and suction side improves the static pressure recovery across the fan. Fences provided at the radial mid-span on the pressure side of the diffuser vane and near the leading edge and trailing edge of the suction side of diffuser vanes also improve the static pressure recovery across the fan.

• Asian-Australasian Journal of Animal Sciences
• /
• v.19 no.6
• /
• pp.811-815
• /
• 2006

The objective of this study was to evaluate the effect of electric fan installation for milk production improvement of dairy cattle in Thailand. The study was conducted using 2 small-holder dairy farms in Chiang Mai province, during April to August 2004. Electric fans were installed in front of each row of cows. Each of the two rows of cows in the barn was defined as an experimental unit, thus each farm had two experimental units. The fans were operated alternately in 7-day intervals between rows of cows within each farm during the day or between 8.00 am to 8.00 pm. Non-operation periods were used as control. Milk yields were recorded. Data on environmental temperature and humidity were obtained from Chiang Mai Meteorological Center. Result from statistically analysis of milk record suggested an interaction between lactation period and fan installation. Therefore, this interaction term of lactation period and fan installation (PERIOD_FAN) was added as a variable to the regression model. Due to the repeated data collection of milk yield from the same cow (alternate week), milk yield was analyzed by repeated measure analysis (Mixed model). Least square means were calculated for all levels and used to compare between each pair-wise values. The final data were collected from the total of 18 cows with 2,072 data. Overall means and SEM of milk yields and days in milk separated into farm were $14.7{\pm}0.06kg/day$ and $176.3{\pm}2.2days$, and $15.2{\pm}0.22kg/day$ and $202.5{\pm}3.7$ days for farm A and farm B, respectively. For multivariable analysis, only PERIOD_FAN and humidity were significantly associated with milk yield. Only the first period of lactation showed that the amount of milk yields during fan installation was higher than that of non-fan installation (p<0.05). Cows with fan installation produced approximately 1.2 kg/cow more milk than cows without fan installation during this period. In conclusion, the use of electric fan operated during the day time increased milk production of cows during the first period of lactation.

• Management & Information Systems Review
• /
• v.30 no.4
• /
• pp.385-414
• /
• 2011

Fans' role and influence is becoming more extensive in these days' complex and competitive sports market. This research considers fans as internal members of sports team, employee and confirms active and voluntary fan citizenship behavior's effects on team, community, and social exchange among community residents, so that an enterprise can increase accessibility from many-sided perspectives when establishing sports marketing strategy in the future. The concept of fan citizenship behavior is set up considering characteristic of sports industry based on employee's organizational citizenship behavior discussed from the internal marketing and organization theory and preliminary studies about client citizenship behavior mentioned from service industry area. Although the sixteen research hypothesis are not fully supported. The results are summarized as follows. These findings give theoretical and marketing implication to future researcher and marketer. First, fan's positive aspect is confirmed which is different from general consumer by examining fan citizenship behavior's effect on teal value in the sports industry. Second, it was confirmed that the team needs marketing strategies about not only relationship between each individual fan, but also interaction between fans in the future. Third, it was confirmed that direct fan's behavior as well as individual fan's cognitive area have effects on team's and social value.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.18 no.2
• /
• pp.743-750
• /
• 2017

It is important to ensure a uniform temperature distribution in greenhouses for the mushroom cultivation. The air temperature of the mushroom cultivation greenhouse is made uniform by supplying a constant air temperature with the underground air. The mushroom cultivation array in a greenhouse in seven columns and four rows can make smooth air flows between the rows and prevent air differences between the top and bottom. The buoyancy effect in the entering air of 0.5m/s based on following density difference depending on initial internal temperature needs to be considered. The locations of the Fan Coil Unit (FCU) and fan were defined through flow analysis in a greenhouse to distribute the optimal uniform temperature. In this study, the air conditioning system of a greenhouse with a sandwich heat insulting panel shape which is composed of a FCU and fan was designed by flow analysis. A relatively uniform temperature distribution can be formed because the circulation path of air becomes longer in the different locations of the FCU (inlet) and fan (outlet) through the internal temperature and flow analysis. The cultivation and quality uniformity of the mushrooms could be promoted through these environmental improvements.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2006.05a
• /
• pp.809-812
• /
• 2006

This article shows the study on the arresting sound occurrence due to the interaction of the centrifugal Fan and bellmouth suction flow with bellmouth height as variable. It has accomplished to measure of inlet noise and also to analysis suction pressure distribution through experiment and also using CFD. The main cause of sound occurrence was judged with the effect due to static pressure change of bellmouth surface.