• Journal of the Korea Institute of Building Construction
• /
• v.20 no.5
• /
• pp.449-457
• /
• 2020

Due to the improvement of living standards and avoidance of the 3D industry, it is difficult to find young and competent domestic workers at construction sites, and most foreign workers are contributing to the replacement, but the quality is still deteriorating due to lack of skilled workers and aging. Precast method is a method that make members in factory and assembles them on site, which can be expected to improve labor force and quality. This study is intended to provide basic data for the development of hang-type PC beams that can be applied to the determination of the field application of developed PC beams. The U-type connecting material is installed on both ends of the hang-up PC beam, and the role of the U-type connecting material is very important because it is a simple construction method through the U-type connecting material. In addition, the performance of the U-type connecting material will determine the performance of the hang-type PC beam as the final destruction occurs in the hang-type PC beam. The material properties of U-type connecting material were identified through structural experiments, and the end test corresponding to the partial experiment was conducted based on the material test results identified. Finally, the final design value of PC beams was proposed through structural experiments for application to the site.

• Korean Journal of Construction Engineering and Management
• /
• v.22 no.6
• /
• pp.120-130
• /
• 2021

Recently, the government is reinforcing safety management at construction sites to prevent safety accidents in construction works, and the safety management plan of workers is an important situation. Meanwhile, modular construction is expected to be gradually expanded to middle and high-rise buildings, but active measures to ensure worker safety are insufficient. This study is a preliminary study of the development of a checklist for preventive worker safety management. The purpose of this study is to derive a checklist classification system for the safety management of workers in the field of modular construction by preceding studies, case analysis, and expert advisory opinions. The classification system consists of large categories of factory manufacturing, transportation, and on-site construction, and the sub-system consists of six sub-classes: foundation work, frame work, modular frame installation work, finishing work, and facility work. Among them, the sub-classification of modular frame installation work consists of 12 unit works, centering on module lifting and assembly module work, which are the main construction processes. And the classification system reflects the three main management factors and contents for defined safety management. It is expected that the research results of this study can contribute to efficient safety management at the modular construction site.

• Journal of Korean Society of Occupational and Environmental Hygiene
• /
• v.11 no.2
• /
• pp.135-144
• /
• 2001

This study was performed to measure airborne dimethylformamide(DMF), methyl ethyl ketone(MEK) and toluene and their urinary metabolites concentrations and to determine the relationship between airborne and urinary concentration. Airborne samples and their urinary metabolites were measured 98 male workers who work for 8 synthetic leather factories in a portion of Kyoung-In area. Urine samples were collected at end-of-shift to estimate the exposure levels. 1. The concentration of airborne DMF by process was 8.81 ppm for wet-mixing, 15.05 ppm for wet-coating, 6.03 ppm for dry-mixing, 5.58 ppm for dry-coating, 5.37 ppm for printing, and 9.03 ppm for total. There was statistically significant difference by process. Urinary NMF concentrations of wet-mixing, wet-coating, dry-mixing, dry-coating and printing were $90.55mg/{\ell}$, $79.80mg/{\ell}$, $39.86mg/{\ell}$, $25.23mg/{\ell}$, and $38.15mg/{\ell}$, respectively, and total geometric mean was $56.24mg/{\ell}$. There was significant difference by process. 2. The concentration of airborne MEK by process was 1.89 ppm for wet-mixing, 1.96 ppm for wet-coating, 10.33 ppm for dry-mixing, 29.24 ppm for dry-coating, 14.98 ppm for printing, and 4.87 ppm for total. There was statistically significant difference by process. Urinary MEK concentrations of wetmixing, wet-coating, dry-mixing, dry-coating and printing were $0.93mg/{\ell}$, $0.70mg/{\ell}$, $3.29mg/{\ell}$, $3.29mg/{\ell}$, and $1.06mg/{\ell}$, respectively, and total geometric mean was $1.25mg/{\ell}$. There was statistically significant difference by process. Urinary MEK 3. The concentration of airborne toluene by process was 0.35ppm for wet-mixing, 0.42ppm for wet-coating, 2.95ppm for dry-mixing, 11.67ppm for dry-coating, 4.88ppm for printing, 1.24ppm for total. There was statistically significant difference by process. Urinary hippuric acid concentrations of wet-mixing, wet-coating, dry-mixing, dry-coating and printing were 0.24g/g creatinine, 0.21g/g creatinine, 0.34g/g creatinine, 0.52g/g creatinine, and 0.29g/g creatinine, respctively and total geometric mean was 0.28g/g creatinine. There was statistically significant difference by process. 4. No. of exceeded KPEL was 40 workers(40.8%) for DMF(10ppm), 1 worker(1.0%) for MEK(200ppm), and no worker for toluene(100ppm). No. of exceeded KBEI was 62 workers(63.3%) for urinary NMF($40mg/{\ell}$), 29 workers(29.6%) for urinary MEK, 1 worker(1.0%) for urinary hippuric acid. 5. The regression equations were Log(NMF)=0.4094*Log(DMF)+1.3587(r=0.4516) for DMF, Log(MEKU)=0.1859*Log(MEK)-0.0324(r=0.3303) for MEK, Log(HA)=0.2106*Log(Toluene)-0.5685(r=0.4497) for toluene. Synthetic leather factory workers expose to 3 kinds of organic solvents which are DMF, MEK and toluene. Their urinary NMF and MEK levels were higher than their concentration levels through respiratory. It seems that the urinary levels were affected skin absorption for working habit and alcohol intake.

• Journal of Preventive Medicine and Public Health
• /
• v.35 no.3
• /
• pp.205-213
• /
• 2002

Objective : Whether exposure to chronic noise induces an increase in blood pressure, or the development of hypertension, has not been established. A cohort study was performed to identify the effects of chronic noise exposure on blood pressure. Methods : 530 males working at a metal manufacturing factory in Busan, Korea were enrolled for the study. They were monitored for 9 consecutive years, from 1991 to 1999, with an annual health check-up. The subjects were divided into 4 groups, which were determines by noise level categories(NLC) according to noise intensity ; NLC-I: office workers, exposed to noise a level below 60dB(A) ; NLC-II: field technical supporters or supervisors, frequently exposed to workplace noise, wearing no hearing protection device; NLC-III: workers, exposed to workplace noise below 85dB(A), wearing ear plugs or muffs; NLC-IV: workers, exposed to workplace noise over 85 dB(A), wearing both ear plugs and muffs. Results : After controlling possible confoundens, such as baseline age, smoking, alcohol intake, exercise, family history of hypertension, systolic(SBP) of diastolic blood pressure(DBP) and changes in BMI (body mass index), the pooled mean for the systolic blood pressures, over the duration of the study period, were 3.8mmHg, 2.0mmHg and 1.7mmHg higher in NLC-IV, NLC-III NLC-II groups, respectively, than in the NLC-I group. There were no significant differences in the diastolic blood pressures between the groups. Conclusion : This study suggests that chronic noise exposure increases systolic blood pressure independently, among male workers.

• Korean Journal of Construction Engineering and Management
• /
• v.15 no.1
• /
• pp.11-19
• /
• 2014

The Construction industry is a labor-intensive industry that its labor cost takes up about 30~40% out of the whole construction cost. However, due to a stereotype that on-site work is a 3D job there is a shortage of the labor forces. Modular construction method is to produce modular units in the plant so that workers could work stably. Also, after delivering the module from plant to the site, there will be only installment to be required that shortens construction duration. Even though the modular market is currently expanding based on military facilities in Korea, its best strengths are not demonstrated well which are shortened construction period and low cost. It also causes labor problem of production due to minimum utilization of the modular construction method. Multi-skilled labor means a technician that is able to perform more than two kinds of work with more than two techniques. Multi-skilled labor can proceed smoothly by figuring out the connectivity between the precedent and following operations. Therefore, this research is to apply the concept of Multi-skilled labors, suggest solutions and allocate manpowers efficiently. As a result, it helps to decrease idle manpowers during the operation and the total labor forces can be saved. Low cost is the original strength of the modular which can stand out so the modular market is expected to expand.

• Journal of the Korean Applied Science and Technology
• /
• v.37 no.2
• /
• pp.214-223
• /
• 2020

This study evaluated CO₂ removal efficiency, monitoring data analysis / evaluation efficiency and energy reduction efficiency in the liquor factory by L-alanine applied scrubber. The average removal rate of the scrubber was 90.45%, and it was confirmed that the removal efficiency was excellent above 10,000ppm of inlet CO₂ concentration. After the scrubber operation, the CO₂ concentration in the workplace was maintained under 2,000ppm(the carbon dioxide reduction efficiency was about 74%). and the energy saving efficiency was calculated to 7.26% by reducing the power consumption. As a result of applying the developed product, it was possible to improve the working environment of workers by reducing the carbon dioxide concentration in the workplace at low concentration without ventilation, and to reduce the energy consumption. Therefore, it is expected that the scrubber will be useful as a high CO₂ removal process in food and liquor factories.

• Korean Journal of Construction Engineering and Management
• /
• v.16 no.5
• /
• pp.54-64
• /
• 2015

The modular construction has several advantages such as high quality of product, safe work condition and short construction duration. The manufacturing planning of modular construction should consider time frame of manufacturing, transport and erection process with limited resources (e.g., modular units, transporter and workers). The manufacturing planning of multi modular construction project manages the modular construction's characteristics and diversity of projects, as a type of modular unit, modular unit quantities, and date for delivery. However, current modular manufacturing planning techniques are weak in dealing with resource interactions and each project requirement in multi modular construction project environments. Inefficient allocation of resources during multi modular construction project may cause delays and cost overruns to construction operation. In this circumstance, this research suggest a manufacturing planning model for schedule optimization of multi project of modular construction, using genetic algorithm as one of the powerful method for schedule optimization with multiple constrained resources. Comparing to the result of the existed schedule of case study, setting optimized scheduling for multi project decrease the total factory producing schedule. By using proposed optimization tool, efficient allocation of resource and saving project time is expected.

• Korean Journal of Construction Engineering and Management
• /
• v.13 no.1
• /
• pp.106-117
• /
• 2012

The proportion of rebar factory manufacturing which has been settled down in Korea recently seems to increase because of their strength such as high decreasing rate of rebar loss and manufacturing accuracy and the external factors such as an increase of downtown projects and a decrease of skilled workers. However, factory manufacturing using straight rebars causes a certain amount of rebar loss and an environmental problem including $CO_2$ emissions. To solve these problems, Bar in coil (BIC) has been introduced; however its application is very rare because it has not been produced so far in Korea and manufacturing machines of BIC are very expensive. Also, although BIC's application is expected to expand due to its strengths, few analysis of its application has been conducted. Therefore in this study, analysis of the BIC's characteristics and the influence to the rebar manufacturing industry are conducted for the advancement of rebar work as a basic research. To achieve this, inquiry on the present condition of rebar manufacturing industry in Korea is implemented. Then, the validation of BIC's applications by aspects of industry and the analysis of stakeholders' economical profit and loss are conducted.

• Journal of agricultural medicine and community health
• /
• v.25 no.1
• /
• pp.1-9
• /
• 2000

A public perception survey of environmental health due to small-scale industries was conducted in Sudong Myun, Namyangju City, Kyungki Do, recently being changed to industrialized rural community. This survey had the purpose to ascertain public interest, to identify public needs, and to assess participation for environmental health programs of rural community. The results of survey were as follows: 1. The rate of the respondents with factory worker 19.4% and half(53.1%) of respondents had lived nearby the factory. 2. Some respondents were not favor their neighboring factories(30.1%) and have discussed about its environmental problems in community meeting(14.4%) especially in neighborhood adjacent factories. 3. The respondents have perceived that: (1) major problems were water contamination, air pollution, nasty odor, dust, and noise (2) health problems were more serious in employees than in other residents (3) the employers were responsible for environmental problems (4) the health service should provided by public health center channel and participated by the residents (5) most important service for workers was improvement of working conditions. We hope the community environmental and/or occupational health delivery system for the employees and residents will be developed true public health center channel in a rural community on the basis of this result.

• 월간산업보건
• /
• s.8
• /
• pp.4-30
• /
• 1988

Examination of working environments was conducted to get more detailed data about harmful working environments and to make a contribution to more effective management. Study was carried out on 722 factories located in Taegu city and eight counties in Kyungpook Province, Korea, for a period of one year, from February 1 to December 30, 1986. The total number and proportion of workers exposed to harmful material was 37,697, 45.2% among 83,368 workers. The results according to exposed material were as follows: 1. In the case of noise, proportion of exceeding the 8-hour TLV was 59%, Included were nail-cutting in assembly metal manufacturing industry and weaving process in textile. 2. Dust in mill process of coal manufacturing industries exceeded the TLV of second class of dust at all parts and exceeded the TLV at 6% as a whole.: 3. The fields of industry lower than 70 lux of illumination were storage equipment of food, auto-winder of textile, painting of wood wares and coal mixing, and 44% of all cases was lower than standard. 4. As a result of temperature index investigation(WBGT), about 12% of all sujects exceeded limit value. Included parts were rolling machine and reducing room. 5. In the case of organic solvents, TLV was exceeded at about 8%, The parts exceeded TLV according to materials belonged to this category were as follows. 1) Toluene: adhesive work in assembly metal manufacturing 2) Xylene: printing and paint mixing in chemical manufacturing 3) Methyl ethytl ketone: paint mixing in all parts examined and coating machine partially in chemical manufacturing 4) Methyl isobutyl ketone: printing in chemical manufacturing 5) Acetone: vapor polishing in assembly metal manufacturing 6. Among specified chemical materials, the concentration of HC1 in the air in metal assembly manufacturing factory exceeded TLV. in one of three assembly metal manufacturing examined. Others, such as benzene, acetic acid, formic acid, sodium hydroxide, formalin, ammonia, copper, chromate etc. were lower than TLV in its indoor atmospheric concentration. As a whole, the proportion of exceeding TLV was about 0.8% 7. The concentrations of inorganic lead were lower than TLV in all parts examined. The results of this investigation show the fact that current management of working environments is not satisfactory, and so more active management is needed.