• Korean Journal of Environment and Ecology
• /
• v.30 no.1
• /
• pp.130-134
• /
• 2016

How does $CO_2$ affect on the stomatal mechanism? The mechanism of stomatal opening by $CO_2$ is not clear as it is difficult to see $CO_2$ effect on light-induced stomatal opening. Furthermore, stomata may react differently according to the concentration of $CO_2$. The significance of the possible endogenous rhythms must consider to understand on $CO_2$-related response. It is clear that $CO_2$ has an effect on the accumulation of osmotic materials which determines the degree of stomatal apertures because it is known that stomata open in the condition of the reduced $CO_2$ concentration. However, it is not fully understood how $CO_2$ leads to the stomatal opening. It has been thought that $CO_2$ can not affect on the ion fluxes which determines the increase of osmotic potential in guard cells. However, in this study, the changes of guard cell membrane permeability by $CO_2$ have been focused on. There are many reports that $CO_2$ related reactions are dominant when the leaf is exposed to certain a mount of $CO_2$. The hypothesis of the stomatal opening by light is based on the increase of osmotic materials in guard cells including $K^+$, $Cl^-$, sucrose and $malate^{2-}$. It was reported that $CO_2$ induced a big hyperpolarization indicating that $H^+$ was extruded to the cell outside. It was also found that $CO_2$ caused guard cell membrane hyperpolarization in the intact leaf up to 3 or 4 times higher than that of light induced membrane hyperpolarization. These results represent that $CO_2$ can affect on the change of physical characteristics which affects on the change of the membrane permeability.

• Korean Journal of Air-Conditioning and Refrigeration Engineering
• /
• v.29 no.6
• /
• pp.327-340
• /
• 2017

This article reviews the papers published in the Korean Journal of Air-Conditioning and Refrigeration Engineering during 2016. It is intended to understand the status of current research in the areas of heating, cooling, ventilation, sanitation, and indoor environments of buildings and plant facilities. Conclusions are as follows. (1) The research works on the thermal and fluid engineering have been reviewed as groups of flow, heat and mass transfer, the reduction of pollutant exhaust gas, cooling and heating, the renewable energy system and the flow around buildings. CFD schemes were used more for all research areas. (2) Research works on heat transfer area have been reviewed in the categories of heat transfer characteristics, pool boiling and condensing heat transfer and industrial heat exchangers. Researches on heat transfer characteristics included the results of the long-term performance variation of the plate-type enthalpy exchange element made of paper, design optimization of an extruded-type cooling structure for reducing the weight of LED street lights, and hot plate welding of thermoplastic elastomer packing. In the area of pool boiling and condensing, the heat transfer characteristics of a finned-tube heat exchanger in a PCM (phase change material) thermal energy storage system, influence of flow boiling heat transfer on fouling phenomenon in nanofluids, and PCM at the simultaneous charging and discharging condition were studied. In the area of industrial heat exchangers, one-dimensional flow network model and porous-media model, and R245fa in a plate-shell heat exchanger were studied. (3) Various studies were published in the categories of refrigeration cycle, alternative refrigeration/energy system, system control. In the refrigeration cycle category, subjects include mobile cold storage heat exchanger, compressor reliability, indirect refrigeration system with $CO_2$ as secondary fluid, heat pump for fuel-cell vehicle, heat recovery from hybrid drier and heat exchangers with two-port and flat tubes. In the alternative refrigeration/energy system category, subjects include membrane module for dehumidification refrigeration, desiccant-assisted low-temperature drying, regenerative evaporative cooler and ejector-assisted multi-stage evaporation. In the system control category, subjects include multi-refrigeration system control, emergency cooling of data center and variable-speed compressor control. (4) In building mechanical system research fields, fifteenth studies were reported for achieving effective design of the mechanical systems, and also for maximizing the energy efficiency of buildings. The topics of the studies included energy performance, HVAC system, ventilation, renewable energies, etc. Proposed designs, performance tests using numerical methods and experiments provide useful information and key data which could be help for improving the energy efficiency of the buildings. (5) The field of architectural environment was mostly focused on indoor environment and building energy. The main researches of indoor environment were related to the analyses of indoor thermal environments controlled by portable cooler, the effects of outdoor wind pressure in airflow at high-rise buildings, window air tightness related to the filling piece shapes, stack effect in core type's office building and the development of a movable drawer-type light shelf with adjustable depth of the reflector. The subjects of building energy were worked on the energy consumption analysis in office building, the prediction of exit air temperature of horizontal geothermal heat exchanger, LS-SVM based modeling of hot water supply load for district heating system, the energy saving effect of ERV system using night purge control method and the effect of strengthened insulation level to the building heating and cooling load.

• The Journal of the Petrological Society of Korea
• /
• v.17 no.2
• /
• pp.108-131
• /
• 2008

The Miocene andesite and basalt intruded into and/or extruded on the Cretaceous volcanic and granitic rocks over the area of Chenjabong and Sirubong in the vicinity of Jinhae, southern part of Kyongsang basin. The K-Ar ages of the younger volcanic rocks are from 16 Ma (Sirubong andesite) to 10 Ma (Cheonjabong basalt), which indicate the Miocene volcanism in the outer part of the Tertiary basin in the Korean peninsula. The volcanics are divided into Chenjabong andesite, Cheonjabong basaltic andesite, Sirubong andesite and Cheonjabong basalt. The Cheonjabong andesite is composed of phenocrysts of clinopyroxene and plagioclase ($An_{60{\sim}64}$) and groundmass with lath-like plagioclase ($An_{76{\sim}84}$) and glass. The Cheonjabong basaltic andesite is composed of plagioclase phenocryst ($An_{60{\sim}64}$) with plagioclase lath ($An_{65}$) and glass in groundmass. The Sirubong andesite is only consisted of plagiocalse lath ($An_{64{\sim}68}$) and glass with absence of phonocryst. The Cheonjabong basalt shows typical porphyritic texture with phenocrysts of olivine ($Fo_{69-84}$) and clinopyroxene. The groundmass of the Cheonjabong basalt is composed of microphenocrysts of olivine, clinopyroxene and plagioclase ($An_{66{\sim}71}$) and plagioclase laths ($An_{57{\sim}65}$) showing pillotaxitic and intergranular texture. The Cheonjabong andesite, Cheonjabong basaltic andesite, Sirubong andesite are belong to calc-alkialine but the Cheonjabong basalt is alkaline basalt. By tectonic discrimination diagrams the parental magmas of the volcanic rocks have occurred boundary.

• Reproductive and Developmental Biology
• /
• v.29 no.3
• /
• pp.175-180
• /
• 2005

This study was conducted to examine the effects of demecolcine-assisted enucleation and recipient cell cycle stage on the development of bovine somatic cell nuclear transfer (NT) embryos. In vitro cultured oocytes for $16\~20$ h were classified by first polar body (1st PB) extrusion and cell cycle stage (MI and MII) and treated $0.4\;{\mu}L/mL$ demecolcine for 40 min before enucleation. Enucleated oocytes were fused electrically with bovine ear skin cells, activated by Ca-ionophore+DMAP, and cultured in vitro. Most of eggs ($86.2\%$) treated with demecolcine protruded a chromosome mass and enucleated efficiently ($98.8\%$, (P<0.05). Demecolcine did not have a deteriorative effect on the development of NT embryos. Developmental rate of NT embryos reconstituted with oocytes extruded 1st PB significantly higher than that of NT embryos produced by oocytes without 1st PB ($18.2\%\;vs.\;4.6\%\cdot$, P<0.05). Cleavage and blastocyst formation rate of embryos reconstituted with MI oocytes ($69.4\%\;and\;5.9\%$, respectively) were significantly lower than those of embryos reconstituted with MII oocytes ($96.7\%\;and\;23.9\%$, respectively, P<0.05). From the present result, it is suggested that domecolcine is useful for the enucleation of recipient oocytes in bovine NT procedures, and MII oocytes rather than MI oocytes are more appropriate for recipient cytoplasm. Although, the potential to develop into blastocysts of NT embryos produced by 1st PB-nonextruded and MI oocytes was very low, these oorytes could be used for NT.

• Proceedings of the Materials Research Society of Korea Conference
• /
• 2011.05a
• /
• pp.14-14
• /
• 2011

W (tungsten)-alloys will be the most promising plasma facing armor materials in highly loaded plasma interactive components of the next step fusion reactors due to its high melting point, high sputtering resistance and low deuterium/tritium retention. The bonding technology of tungsten to Cu alloy was one of the key issues. In this paper, W/CuCrZr diffusion bonding has been performed successfully by inserting pure metal interlay. The joint microstructure, interfacial elements migration and phase composition were analyzed by SEM, EDS, XRD, and the joint shear strength and micro-hardness were investigated. The mock-ups were fabricated successfully with diffusion bonding and the cladding technology respectively, and the high heat flux test and thermal fatigue test were carried out under actively cooling condition. When Ni foil was used for the bonding of tungsten to CuCrZr, two reaction layers, Ni4W and Ni(W) layer, appeared between the tungsten and Ni interlayer with the optimized condition. Even though Ni4W is hard and brittle, and the strength of the joint was oppositely increased (217 MPa) due primarily to extremely small thicknesses (2~3 ${\mu}m$). When Ti foil was selected as the interlayer, the Ti foil diffused quickly with Cu and was transformed into liquid phase at $1,000^{\circ}C$. Almost all of the liquid was extruded out of the interface zone under bonding pressure, and an extremely thin residual layer (1~2 ${\mu}m$) of the liquid phase was retained between the tungsten and CuCrZr, which shear strength exceeded 160 MPa. When Ni/Ti/Ni multiple interlayers were used for bonding of tungsten to CuCrZr, a large number of intermetallic compound ($Ni_4W/NiTi_2/NiTi/Ni_3T$) were formed for the interdiffusion among W, Ni and Ti. Therefore, the shear strength of the joint was low and just about 85 MPa. The residual stresses in the clad samples with flat, arc, rectangle and trapezoid interface were estimated by Finite Element Analysis. The simulation results show that the flat clad sample was subjected maximum residual stress at the edge of the interface, which could be cracked at the edge and propagated along the interface. As for the rectangle and trapezoid interface, the residual stresses of the interface were lower than that of the flat interface, and the interface of the arc clad sample have lowest residual stress and all of the residual stress with arc interface were divided into different grooved zones, so the probabilities of cracking and propagation were lower than other interfaces. The residual stresses of the mock-ups under high heat flux of 10 $MW/m^2$ were estimated by Finite Element Analysis. The tungsten of the flat interfaces was subjected to tensile stresses (positive $S_x$), and the CuCrZr was subjected to compressive stresses (negative $S_x$). If the interface have a little microcrack, the tungsten of joint was more liable to propagate than the CuCrZr due to the brittle of the tungsten. However, when the flat interface was substituted by arc interfaces, the periodical residual stresses in the joining region were either released or formed a stress field prohibiting the growth or nucleation of the interfacial cracks. Thermal fatigue tests were performed on the mock-ups of flat and arc interface under the heat flux of 10 $MW/m^2$ with the cooling water velocity of 10 m/s. After thermal cycle experiments, a large number of microcracks appeared at the tungsten substrate due to large radial tensile stress on the flat mock-up. The defects would largely affect the heat transfer capability and the structure reliability of the mock-up. As for the arc mock-up, even though some microcracks were found at the interface of the regions, all microcracks with arc interface were divided into different arc-grooved zones, so the propagation of microcracks is difficult.

• Korean Journal of Fisheries and Aquatic Sciences
• /
• v.15 no.4
• /
• pp.283-290
• /
• 1982

Sardine and mackerel so called dark muscled fish have been underutilized due to the disadvantages in bloody meat color, high content of fat, and postmortem instability of protein. Recent efforts were made to overcome these defects and develope new types of product such as texturized protein concentrates and dark muscle eliminated minced fish. Approach of this study is based on the rapid dehydration of foamed fish-starch paste by dielectric heating. In process comminuted sardine meat was washed more than three times by soaking and decanting in chilled water and finally centrifuged. The meat was ground in a stone mortar added Ivith adequate amounts of salt, foaming agent, and other ingredients for aid to elasticity and foam stability. The ground meat paste was extruded in finger shape and heated in a microwave oven to give foamed, expanded, and porous solid structure by dehydration. Dielectric onstant $(\varepsilon')$ and dielect.ic loss $(\varepsilon")$ values of sardine meat paste were influenced by wavelength and moisture level. Those values at 100 KHz and 15 MHz were ranged 2.25-9.86; 2.22-4,18 for E' and 0.24-19.24; 0.16-1.20 for E", respectively, at the moisture levels of $4.2-13.8\%$. For a formula for fish-starch paste preparation, addition of $20-30\%$ starch (potato starch) to the weight of fish meat, $2-4\%$ salt, and $5-10\%$ soybean protein was adequate to yield 4-5 folds of expansion in volume when heated. Addition of e99 yolk was of benefit to micronize foam size and better crispness. In order to provide better foaming and dehydration, addition of $0.2-0.5\%$sodium bicarbonate, foaming agent, was proper to result in foam size of 0.5-0.7 mm and foam density of $200-400\;/cm^2$ which gave a good crispness. Heating time was depended upon the moisture level of fish-starch paste. For a finger shaped paste (1.0cm. $D\times10cm.L$) heating for 150-200 sec. in a microwave oven (700W. 2.45GHz) was sufficient to generate foams, expand, and solidify the porous structure of fish-starch paste. When the moisture content was above $55\%$ browning and scorching was deepened due to over-expansion and over-heating whereas the crispness was hardened by insufficient expansion at lower moisture content. In quality evaluation of the product, chemical composition of $30\%$ starch and $3\%$ salt added product was moisture $8.8\%$, lipid $2.4\%$, carbohydrate $46.7\%$, protein $36.1\%$, and ash $6.0\%$. Eleven membered panel test evaluated that fish-starch paste was acceptable in color, crisp-ness, taste, except a trace of fishy odour which could be masked by the addition of spice extracts.

• Korean Journal of Fisheries and Aquatic Sciences
• /
• v.18 no.6
• /
• pp.586-593
• /
• 1985

The rose bitterling, Rhodeus ocellatus (KNER) is commonly distributed in the fresh waters of Korea and Japan. On January 15, February 15, and March 18 in 1984, mature adults of rose bitterling were caught in the watercourse of Maeri, Kimhae, South Korea. The authors fertilized the eggs employing dry method in the laboratory on May 7, 16 and 25 in 1984. Hatched larvae were reared in small aquariums at $17{\sim}25.5^{\circ}C$ (average around $21.2^{\circ}C$). Mollusks, Anodonta woodiana in the gill chamber of which, rose bitterling lay eggs were caught in order to study natural spawning of the rose bitterling in the same watercourse. The eggs of this species are not adhesive and demersal. The size of the eggs varies from 2.54 to 2.75mm in long diameter and 1.45 to 1.65mm in short diameter. The eggs are cylindrical in form when they are extruded from ovipositor, immediately after entering water, but they acquire their distinctive form of a greatly elongated pear. Hatching took place in ca. 39 hours after fertilization. The newly hatched larvae were $2.65{\sim}2.70mm$ in total length possessing yolk sac and 13-14 myotomes. Thirteen days after hatching, the prelarvae attained 6.5 mm in total length, and the first melanophores appeared on the head, and the anterior part and sides of the yolk sac. One month after hatching, the postlarvae attained 8.5mm. in total length and emerged from the gills of the mollusks. Then the yolk sac was completely resorbed. Two months after hatching, the rose bitterling attained 14.4mm in total length, and entered the fingerling period of life. All the rays already present were the D. III, 11-12, A. III, 11-12, P. 10, V. 7. and a distinguishing, feature is the presence of a black pigment spot in the lobe of the dorsal fin.

• Korean Journal of Food Science and Technology
• /
• v.30 no.5
• /
• pp.1128-1133
• /
• 1998

Extrusion cooking treatment was compared with autoclaving/cooling treatment for formation of enzyme resistant starch of high amylose corn starch (HACS). Effects of barrel temperature $(100^{\circ}C,\;120^{\circ}C,\;140^{\circ}C)$ and feed moisture content (25%, 35%, 45%) on extrusion processing in a co-rotating twin-screw extruder under fixed screw speed (100 rpm) were investigated by measuring enzyme resistant starch (RS) yield. RS yield were estimated by in-vitro pancreatin digestion method and enzymatic-gravimetric method using termamyl. Barrel temperature and yield of RS were negatively correlated and feed moisture content and yield of RS was positively correlated as determined by in-vitro pancreatin method. The highest yield (38.4%) of RS was obtained from HACS extrudate processed at the barrel temperature of $100^{\circ}C$ and the feed moisture content of 45%, while the yield of RS by 5 times of autoclaving/cooling was 25%. The yield of RS by in vitro pancreatin digestion method was 20.7% with high amylose corn starch and 8.2% with ordinary corn starch (CS), respectively, under the same extrusion condition (barrel temperature $120^{\circ}C$, feed moisture content 35%). At the same condition, the yields of RS by enzyme-gravimetric method were 14.6% with HACS and 6.8% with CS, respectively. The yield of RS increased during the storage at $4^{\circ}C$ for 4 weeks and the highest yield (60%) was obtained by the storage of HACS extrudates extruded at $100^{\circ}C$ and 45% feed moisture content.

• The Journal of the Petrological Society of Korea
• /
• v.26 no.3
• /
• pp.201-219
• /
• 2017

The Jinan Basin which includes Maisan locates in the central part of the northern boundary of the Yeongnam Massif. The basement rocks of the Jinan Basin and surrounding area are Precambrian gneiss and Mesozoic granite which were exposed on the surface before Cretaceous. The Jinan Basin, one of the Cretaceous pull-apart basins in South Korea, formed along the Yongdong-Gwangju fault system. Maisan is composed of conglomerate deposited in the eastern slope of the Jinan Basin showing the shape of horse ears and the unusual topography where many tafonies were developed. The strike slip fault that caused the Jinan Basin was connected to the deep depth so that the magma formed at 200 km depth could have extruded on the surface causing active volcanic activity in and around the Jinan basin. As a result, Cheonbansan composed of pyroclastic rocks, Gubongsan consisting of volcanic neck and WoonilamBanilam formed by the lava flow, appear around Maisan forming a specific terrain. After the formation of the Jinan Basin and surrounding volcanic rocks, they uplifted to form mountains including Masian; the uplifting time may be ca. 69-38 Ma. At this time, the Noryeong mountain range may be formed in the regions which extended from Chugaryeong through Muju and Jinan to Hampyeong dividing the Geumgang and Seomjingang water systems. Due to the ecological barrier, the Noryeong mountain range, Coreoleuciscus splendidus living in the Geumgang water systems was differentiated from that in the Soemjingang water system. In addition, the Geumgang and Mangyeong-Dongjingang water systems were separated by the Unjangsan, which developed in the NNW direction. As a result, diverse ecosystem have been established in and around Maisan and at the same time, diverse cultural and historical resources related to Maisan's unique petrological features, were also established. Therefore, Maisan and surrounding area can be regarded as a place where a geotourism can be successfully established by combining the ecological, cultural and historical resources with a geological heritage. Therefore Maisan and surrounding areas have a high possibility to be a National Geopark and UNESCO Global Geopark.

• Restorative Dentistry and Endodontics
• /
• v.31 no.5
• /
• pp.344-351
• /
• 2006

The purpose of this study was to evaluate the thermal expansion characteristics of injectable ther-moplasticized gutta-perchas and a Resilon. The materials investigated are Obtura gutta-percha, Diadent gutta-percha, E&Q Gutta-percha Bar and Epiphany (Resilon). The temperature at the heating chamber orifice of an Obtura II syringe and the extruded gutta-percha from the tip of both 23- and 20-gauge needle was determined using a Digital thermometer. A cylindrical ceramic mold was fabricated for thermal expansion test, which was 27 mm long, with an internal bore diameter of 3 mm and an outer diameter of 10 mm. The mold was filled with each experimental material and barrel ends were closed with two ceramic plunger. The samples in ceramic molds were heated in a dilatometer over the temperature range from $25^{\circ}C$ to $75^{\circ}C$. From the change of specimen length as a function of temperature, the coefficients of thermal expansion were deter-mined. There was no statistical difference between four materials in the thermal expansion in the range from $35^{\circ}C$ to $55^{\circ}C$ (p > 0.05). However, Obtura Gutta-percha showed smaller thermal expansion than Diadent and Metadent ones from $35^{\circ}C$ to $75^{\circ}C$ (p < 0.05). The thermal expansion of Epiphany was similar to those of the other gutta-percha groups.