• KCI Concrete Journal
• /
• v.12 no.1
• /
• pp.101-111
• /
• 2000

It has been a well known fact that buildings having inappropriate expansion joints in their spacings may be subject to exterior damages due to extensive cracks on the outer walls under service loads and structural damages due to excessive moment induced by temperature changes at ultimate load conditions. Unfortunately, consistent code provisions are unavailable regarding spacings of expansion joints from different foreign structural codes. And a more serious problem is that no quantitative measurements on spacings is given in our codes for building structures. In order to establish a rational guideline on the spacing of expansion joints, theoretical approaches are taken in this study. The developed theoretical formula is, then, converted to a design chart for structural designers' convenience in its use. The chart considers both service and ultimate load stages.

• Proceedings of the Korea Concrete Institute Conference
• /
• 1999.10a
• /
• pp.455-458
• /
• 1999

It has been known that buildings having inappropriate expansion joints in their spacings may be subject to exterior damages due to extensive cracks on the outer walls under service loads, and structural damages due to excessive moment induced by temperature changes at ultimate load conditions. Rather inconsistent code provisions are available regarding spacings of expansion joints from different foreign structural codes and even worse, no quantiative measure on spacings is given in our codes for building structures. In order to establish a rational measure on the spacing of expansion joints, theoretical approaches are taken in this study. The developed theoretical formula is, then, converted to design chart for structural designer's convenience in its use. The chart considers both service and ultimate load stages.

• Proceedings of the Korea Concrete Institute Conference
• /
• 1995.04a
• /
• pp.268-273
• /
• 1995

In recent years, precast prestressed concrete segmental box girder bridges have been increasingly constructed Expansion disphragm segment of this type bridge transfers forces from the superstructure onto bearing or column, and plays an important roll of anchorage zone for longitudinal prestressed forces. Non-linear stresses occur inside of diaphragms by these extensive concentrated forces. In this study, the strut-and-tie models are proposed to design an expansion segment rationally. A formula to determine the effective transverse prestressed forces is proposed on the basis of these models. The present study is expected to provide an effective tool to design expansion segment of prestressed concrete bridges rationally.

• Archives of Craniofacial Surgery
• /
• v.20 no.6
• /
• pp.408-411
• /
• 2019

Hairless scalp areas can occur due to trauma, tumors, or congenital disease. This aesthetically unpleasing condition can lead to psychosocial distress, and thin skin flaps may be prone to scarring. Treating the hairless scalp by simple excision is challenging because of skin tension. Tissue expanders are a good option for hairless scalp resurfacing. However, a single expansion may be inadequate to cover the entire defect. This report describes good results obtained using a serial resurfacing method involving re-expansion of the flap with a tissue expander to treat two patients with large lesions: one due to aplasia cutis congenital and another who underwent dermatofibrosarcoma protuberance resection. The results suggest that scalp resurfacing by serial tissue expansion using a tissue expander can be used for extensive lesions.

• Applied Science and Convergence Technology
• /
• v.23 no.3
• /
• pp.103-112
• /
• 2014

The Korea Research Institute of Standards and Science (KRISS) has three major vacuum systems: an ultrasonic interferometer manometer (UIM; Section II, Figs. 1 and 2) for a low vacuum, a static expansion system (SES; Section III, Figs. 3 and 4) for a medium vacuum, and an orifice-type dynamic expansion system (DES, Section IV, Figs. 5 and 6) for high and ultra-high vacuum systems. For each system, explicit measurement model equations with multiple variables are given. According to ISO standards, all of these system variable errors were used to calculate the expanded uncertainty (U). For each system, the expanded uncertainties (k = 1, confidence level = 95%) and relative expanded uncertainty (expanded uncertainty/generated pressure) levels are summarized in Table 4. Within the uncertainty limits, our bilateral and key comparisons [CCM.P-K4 (10 Pa to 1 kPa)] are extensive and in good agreement with those of other nations (Fig. 8 and Table 5).

• Archives of Plastic Surgery
• /
• v.50 no.6
• /
• pp.610-614
• /
• 2023

Necrotizing fasciitis is an uncommon yet fatal soft tissue infection. Current recommended treatment includes antibiotics with repeat surgical exploration and wound debridement followed by reconstruction. In burn patients, the Meek micrograft has demonstrated a higher true expansion ratio, faster reepithelialization rate, more resilient toward infection, and reduced risk of graft failure as compared with meshed graft. To our best knowledge, the use of Meek micrografting technique in reconstruction of postdebridement wounds of necrotizing fasciitis has not been reported. Hereby, we present a case of a 57-year-old gentleman who was referred to us for wound reconstruction after surgical debridement of Fournier's gangrene and extensive necrotizing fasciitis involving the anterior abdomen and bilateral femoral region. Meek micrografting technique was used to reconstruct the anterior abdomen as the wound bed was large. Although the graft was complicated with a small area of localized infection, it did not spread across the entire graft and was successfully treated with topical antibiotics and regular wound dressing. In our case, wound reconstruction using Meek micrografting technique in a patient with extensive necrotizing fasciitis was successful and showed positive outcome. Therefore, we suggest further studies to be conducted to investigate the applications and outcomes of the Meek micrografting technique, especially in patients with extensive wound bed and limited donor site availability.

• Transactions of the Korean Society of Pressure Vessels and Piping
• /
• v.10 no.1
• /
• pp.7-14
• /
• 2014

There has been extensive experience associated with the operation of SGs wherein it was believed, based on NDE, that throughwall tube indications were present within the tubesheet. The installation of the SG tubes usually involves the development of a short interference fit, referred to as the tack expansion, at the bottom of the tubesheet. The tack expansion was usually effected by a hard rolling process and thereafter, in most instance, by the expansion of a urethane plug inserted into the tube end and compressed in the axial direction. The rolling process by its very nature is considered to be intensive with regard to metalworking at the inside surface of the tube and would be expected to lead to higher residual surface stresses. Alternate repair criteria(ARC) in the tack expansion area have been developed and applied to nuclear power plants in USA, however domestic nuclear power plants have not applied ARC for tubes in tubeheet area yet. In consideration of the degradation characteristics of tubes in the Steam Generator tubesheet, this paper suggests ARC application for tubes in the steam generator tubesheet of the domestic nuclear power plants in order to assure life time of the steam generator as well as nuclear power plants.

• Transactions of Materials Processing
• /
• v.16 no.7
• /
• pp.521-529
• /
• 2007

This paper is concerned with the analysis on the surface expansion of AA 2024 and AA 1100 aluminum alloys in backward extrusion process. Due to heavy surface expansion appeared usually in the backward can extrusion process, the tribological conditions along the interface between the material and the punch land are very severe. In the present study, the surface expansion is analyzed especially under various process conditions. The main goal of this study is to investigate the influence of degree of reduction in height, geometries of punch nose, friction and hardening characteristics of different aluminum alloys on the material flow and thus on the surface expansion on the working material. Two different materials are selected for investigation as model materials and they are AA 2024 and AA 1100 aluminum alloys. The geometrical parameters employed in analysis include punch corner radius and punch nose angle. The geometry of punch follows basically the recommendation of ICFG and some variations of punch geometry are adopted to obtain quantitative information on the effect of geometrical parameters on material flow. Extensive simulation has been conducted by applying the rigid-plastic finite element method to the backward can extrusion process under different geometrical, material, and interface conditions. The simulation results are summarized in terms of surface expansion at different reduction in height, deformation patterns including pressure distributions along the interface between workpiece and punch, comparison of surface expansion between two model materials, geometrical and interfacial parametric effects on surface expansion, and load-stroke relationships.

• KDI Journal of Economic Policy
• /
• v.31 no.2
• /
• pp.195-234
• /
• 2009

This paper examines relative contributions of extensive margin and intensive margin of Korean exports growth to China after 1990s', based on an analytical approach proposed by the Hummels and Klenow(2005). In this paper, extensive margin is defined as a weighted count of Korean exports categories relative to the rest of world's export categories to China. On the other hand, intensive margin refers to Korean exports to China relative to the rest of the world's exports to China, exclusively in those product categories that Korea exports to China. According to the results of the analysis, the expansion of Korean exports to China was induced mainly by the increase of intensive margin. This result is consistent with $Besede{\check{s}}$ and Prusa(2007) as well as the Helpman, Melitz and Rubinstein(2007) who suggest that intensive margin is a more important factor than extensive margin for sustaining growth of export in the long term. In addition, this paper shows that the survival rates of exports of parts and components and capital goods is relatively higher in comparison to those of primary and consumption goods. This implies that the expansion of international division of labor under the global production network could substantially affect the survival of exports.

• Journal of Computing Science and Engineering
• /
• v.2 no.1
• /
• pp.26-43
• /
• 2008

We propose a new query expansion method in the extended Boolean model that improves precision without degrading recall. For improving precision, our method promotes the ranks of documents having more query terms since users typically prefer such documents. The proposed method consists of the following three steps: (1) expanding the query by adding new terms related to each term of the query, (2) further expanding the query by adding augmented terms, which are conjunctions of the terms, (3) assigning a weight on each term so that augmented terms have higher weights than the other terms. We conduct extensive experiments to show the effectiveness of the proposed method. The experimental results show that the proposed method improves precision by up to 102% for the TREC-6 data compared with the existing query expansion method using a thesaurus proposed by Kwon et al.