• 한국전산구조공학회:학술대회논문집
• /
• 한국전산구조공학회 1994년도 봄 학술발표회 논문집
• /
• pp.163-170
• /
• 1994

The widening of bridges under traffic condition brings to many problems. One of these is the internal stresses caused by different creep and shrinkage behavior of the existing bridge and that of the widened Bridge. This study was conducted to examine the effects of different creep and shrinkage behaviors between concretes. The results are as follows; Comparing the computational analysis results with the experimental study, it is shown that finite element analysis used in this study was well accorded with experimental results. And considering the shrinkage effects in widened bridges, joining-construction using the expanding concrete between the existing and widened bridge after at least three months from the day of completion of new bridge, is recommended.

• 한국콘크리트학회:학술대회논문집
• /
• 한국콘크리트학회 1994년도 봄 학술발표회 논문집
• /
• pp.13-18
• /
• 1994

Most widened bridges have been constructed by the joining-construction method that makes new and existing bridge structurally single structure. However, joing-construction method has several problems in design and construction viewpoint. Therefore, this study is conducted in order to investigate structural behavior of widened RC slab and traffic-induced vibration of existing bridge during placing and curing of new concrete by the prototype flexural fatigue test. From the results of this study, it is shown that stress-concentration and slip occur between concrete and reinforcing rod at joint section but the reduction of load carrying capacity and of fatigue strength is negligible according to the traffic-induced vibration as well as the difference of construction method. A reasonable construction method for the bridge widening which takes into account the effects of the traffic-induced vibration and S-N curve for the widened bridge are also proposed.

• 한국지진공학회:학술대회논문집
• /
• 한국지진공학회 2001년도 추계 학술발표회 논문집 Proceedings of EESK Conference-Fall 2001
• /
• pp.187-193
• /
• 2001

The object of this research is to evaluate the seismic performance of existing circular reinforced concrete bridge piers by the Quasi-static test. Existing reinforced concrete bridge piers, which were non-seismical]y designed in accordance with the conventional provisions of Korea Highway Design Specification, are needed to rating evaluate seismic performance fur probable earthquake motions in future by developing a seismic analysis computer program with estimation algorithm. This study has been performed to verify the effect of lap spliced longitudinal steel, confinement steel type and confinement steel ratio for the seismic behavior of reinforced concrete bridge piers. Quasi-static test has been done to investigate the physical seismic performance of RC bridge piers, such as displacement ductility, energy absorption, strength degradation etc.

• 한국철도학회:학술대회논문집
• /
• 한국철도학회 2008년도 춘계학술대회 논문집
• /
• pp.1729-1734
• /
• 2008

This study developed a new separated shperical bridge bearing that can be used for replacement of existing bridge bearings without crushing bearing-concrete. The separated spherical bearing have the upper and lower sole plate connected by bolts to the upper plate under bridge-girders and the lower plate on bearing-concrete. The targets of the separated spherical bearing are the maximum 3 mm of up-lifting height during replacement and the maximum required time of 30 minutes. Four separated spherical bearings are manufactured and replaced the existing bearings of a railway bridge in service and the replacing tests was performed. The number of the tests is two and the target of maximum 3 mm and 30 minutes was satisfied.

• 한국지진공학회:학술대회논문집
• /
• 한국지진공학회 2003년도 추계 학술발표회논문집
• /
• pp.288-294
• /
• 2003

Increasing the volume of traffic on the roads causes social and economical problems such as increasing air-pollution and distribution cost. Prefabricated light weight bridge becomes a possible solution for these problems in the urban area where it is difficult to construct new one or expend the existing road. There are some merits in this kind of bridge. First, the design live and dead loads are minimized by allowing only passenger cars. Second employing prefabrication construction scheme reduces the construction time. Third, there is no need to buy land if the elevation road is placed on the top of existing one. In seismic design of bridges, base isolation has been an effective solution when the bridge has stiff piers and a heavy superstructure. The prefabricated light weight bridge has different dynamic characteristics from the ordinary bridges. In this paper, the applicability of base isolators such as lead rubber bearing and elastomeric bearing, to prefabricated light weight bridge is examined.

• Communications for Statistical Applications and Methods
• /
• 제28권3호
• /
• pp.251-265
• /
• 2021

This paper discusses the pricing of autocallable structured product with knock-in (KI) feature using the exit probability with the Brownian Bridge technique. The explicit pricing formula of autocallable ELS derived in the existing paper handles the part including the minimum of the Brownian motion using the inclusion-exclusion principle. This has the disadvantage that the pricing formula is complicate because of the probability with minimum value and the computational volume increases dramatically as the number of autocall chances increases. To solve this problem, we applied an efficient and robust simulation method called the Brownian Bridge technique, which provides the probability of touching the predetermined barrier when the initial and terminal values of the process following the Brownian motion in a certain interval are specified. We rewrite the existing pricing formula and provide a brief theoretical background and computational algorithm for the technique. We also provide several numerical examples computed in three different ways: explicit pricing formula, the Crude Monte Carlo simulation method and the Brownian Bridge technique.

• 콘크리트학회논문집
• /
• 제16권5호
• /
• pp.697-707
• /
• 2004

내진설계편이 제정된 1992년 이전의 설계규정에 따라 설계$\cdot$시공된 교량은 내진상세가 적용되지 않아 지진에 취약할 것으로 예상된다. 특히, 주철근의 겹침이음은 교각의 상당한 내진성능저하를 야기하는 것으로 보고되고있다. 하지만, 이들 교량에 대한 내진성능평가 및 내진보강에 관한 연구는 아직 체계적으로 이루어지지 않고 있는 실정이다. 따라서, 이에 대한 대책마련이 시급한 것으로 사료된다. 본 연구에서는 이러한 비내진 교각의 내진성능을 평가하고자 형상비 4.0인 실물크기의 철근콘크리트 교각시험체를 제작하여 준정적실험을 수행하였다. 실험결과를 통하여 주철근 겹침이음된 비내진교각은 띠철근 형태와 상관없이 현행 도로교설계기준의 요구성능을 만족하지 못하는 것으로 조사되어 시급히 보강을 하여야 할 것으로 판단된다. 또한 주철근 겹침이음에 대한 내진규정의 보완이 요구된다.

• 한국항해항만학회지
• /
• 제38권6호
• /
• pp.645-653
• /
• 2014

A Bridge Navigational Watch Alarm System (hereafter 'BNWAS') is to monitor and detect if an officer of watch(hereafter 'OOW') keeps a sharp lookout on the bridge. The careless lookout of an OOW could lead to marine accidents. For this reason on June 5th, 2009, IMO decided that a ship is equipped with a BNWAS. However, an existing BNWAS gives the OOW a lot of inconvenience and stress in its operation. It requires that the OOW should press reset buttons to confirm their alert watch on the bridge at every three to twelve minute. Many OOWs have complained that at some circumstances they cannot focus on their bridge activities including watch-keeping due to a lots of resetting inputs of BNWAS. Accordingly, IMO has allowed the use of a motion sensor as a resetting device. The motion sensor detects the movements of human body on the bridge and subsequently sends reset signals directly to BNWAS automatically. As a result, OOWs can work uninterrupted. However, some of classification societies and flag authorities have a slightly different stance on the use of motion sensor as a resetting method for BNWAS. The reason is that the motion sensor may trigger false reset signals caused by the motion of objects on the bridge, especially a slight movement such as toss and turn of human body which can extend the period of careless watch. As a basic study to minimize the false reset signals, this paper proposes a simple configuration of BNWAS, which consists of only three motion sensors associated with 'AND' and 'OR' logic gates. Additionally, several considerations are also proposed for the implementation of motion sensors. This study found that the proposed configuration which consists of three motion sensors is better than an existing one by reducing false reset signals caused by a slight movement of human body in one's sleep. The proposed configuration in this paper filters false reset signals and is simple to be implemented on existing vessels. In addition, it can be easily installed just by a basic electrical knowledge.

• Structural Monitoring and Maintenance
• /
• 제2권3호
• /
• pp.283-300
• /
• 2015

Visual condition inspections remain paramount to assessing the current deterioration status of a bridge and assigning remediation or maintenance tasks so as to ensure the ongoing serviceability of the structure. However, in recent years, there has been an increasing backlog of maintenance activities. Existing research reveals that this is attributable to the labour-intensive, subjective and disruptive nature of the current bridge inspection method. Current processes ultimately require lane closures, traffic guidance schemes and inspection equipment. This not only increases the whole-of-life costs of the bridge, but also increases the risk to the travelling public as issues affecting the structural integrity may go unaddressed. As a tool for bridge condition inspections, Unmanned Aerial Vehicles (UAVs) or, drones, offer considerable potential, allowing a bridge to be visually assessed without the need for inspectors to walk across the deck or utilise under-bridge inspection units. With current inspection processes placing additional strain on the existing bridge maintenance resources, the technology has the potential to significantly reduce the overall inspection costs and disruption caused to the travelling public. In addition to this, the use of automated aerial image capture enables engineers to better understand a situation through the 3D spatial context offered by UAV systems. However, the use of UAV for bridge inspection involves a number of critical issues to be resolved, including stability and accuracy of control, and safety to people. SLAM (Simultaneous Localisation and Mapping) is a technique that could be used by a UAV to build a map of the bridge underneath, while simultaneously determining its location on the constructed map. While there are considerable economic and risk-related benefits created through introducing entirely new ways of inspecting bridges and visualising information, there also remain hindrances to the wider deployment of UAVs. This study is to provide a context for use of UAVs for conducting visual bridge inspections, in addition to addressing the obstacles that are required to be overcome in order for the technology to be integrated into current practice.

• 한국철도학회:학술대회논문집
• /
• 한국철도학회 2009년도 춘계학술대회 논문집
• /
• pp.55-65
• /
• 2009

This study is objected by analyzing whether it is applied to the analysis model considering the track stiffness or not when the railway bridge is designed or reviewed for the dynamic stability. It is performed that the analysis model is verified by comparing the field test result with the analysis result. Also, The dynamic response of railway bridge through the existing analysis model is compared with the analysis model considered the track stiffness. In addition, it is performed by analyzing the model considering the stiffness of concrete track. Therefore, this study is suggested that the design of railway bridge apply to the existing analysis model considering the mass of track and the dynamic stability review of railway bridge apply to it considered the stiffness & mass of track. Also, it is suggested that the stiffness of concrete slab on the bridge must consider when it is designed or checked over the dynamic stability.