• 한국농업기계학회:학술대회논문집
• /
• 한국농업기계학회 2000년도 THE THIRD INTERNATIONAL CONFERENCE ON AGRICULTURAL MACHINERY ENGINEERING. V.III
• /
• pp.639-646
• /
• 2000

Hot air heater with light oil combustion is the most common heater for greenhouse heating in the winter season in Korea. However, since the heat efficiency of the heater is about 80%, considerable unused heat in the form of exhaust gas heat discharges to atmosphere. In order to capture this exhaust gas heat a heat recovery system for plant bed heating in the greenhouse was built and tested in the hot air heating system of greenhouse. The system consists of a heat exchanger made of copper pipes, ${\phi}\;12.7{\times}0.7t$ located inside the rectangular column of $330{\times}330{\times}900mm$, a water circulation pump, circulation plastic pipe and a water tame The total heat exchanger area is $1.5m^2$, calculated considering the heat exchange amount between flue gas and water circulated in the copper pipes. The system was attached to the exhaust gas path. The heat recovery system was designed as to even recapture the latent heat of flue gas when exposing to low temperature water in the heat exchanger. According to performance test it can recover 45,200 to 51,000kJ/hr depending on the water circulation rates of 330 to $690{\ell}$/hr from the waste heat discharged. The exhaust gas temperature left from the heat exchanger dropped to $100^{circ}C$ from $270^{circ}C$ by the heat exchange between the water and the flue gas, while water gained the difference and temperature increased to $38^{circ}C$ from $21^{circ}C$ at the water flow rate of $690{\ell}$/hr. And, the condensed water amount varies from 16 to $43m{\ell}$ at the same water circulation rates. This condensing heat recovery system can reduce boiler fuel consumption amount in a day by 34% according to the feasibility study of the actual mimitomato greenhouse. No combustion load was observed in the hot air heater.

• 한국마린엔지니어링학회:학술대회논문집
• /
• 한국마린엔지니어링학회 2002년도 춘계학술대회논문집
• /
• pp.75-82
• /
• 2002

The effects of intake mixture temperature on performance and exhaust emissions under four kinds of engine loads were experimentally investigated by using a four-cycle four-cylinder, swirl chamber type, water-cooled diesel engine with scrubber EGR system operating at three kinds of engine speeds. The purpose of this study is to develop the scrubber exhaust gas recirculation(EGR) control system for reducing $NO_x$ and soot emissions simultaneously in diesel engines. The EGR system is used to reduce NOx emissions. And a novel diesel soot-removal device with a cylinder-type scrubber which has five water injection nozzles is specially designed and manufactured to reduce soot contents in the recirculated exhaust gas to the intake system of the engine. The influences of cooled EGR and water injection, however, would be included within those of scrubber EGR system. In order to study the effect of intake mixture temperature, a intake mixture heating device which has five heating coils is made of a steel drum. It is found that the specific fuel consumption rate is considerably elevated by the increase of intake mixture temperature, and that NOx emissions are markedly decreased as EGR rates are increased and intake mixture temperature is dropped, while soot emissions are increased with increasing EGR rates and intake mixture temperature.

• 대한기계학회논문집A
• /
• 제39권11호
• /
• pp.1105-1111
• /
• 2015

배기계는 엔진 및 현가계와 함께 차량의 주요 가진원 중의 하나이다. 배기계는 엔진과 직접적으로 연결된 시스템으로서 차체와의 연결 마운트를 통하여 엔진 구동 시의 진동을 차체로 전달한다. 따라서 배기계로부터 전달되는 진동을 저감하기 위해서는 배기계 진동특성을 예측해야 하고, 배기계의 주요부품인 벨로우즈의 정확한 특성을 묘사해야 한다. 그러나 벨로우즈는 복잡한 형상으로 인하여 특성을 예측하는 데에 어려움이 있었다. 설계 단계에서 벨로우즈에 대한 등가 변환 이론이 적용되었지만, 구간에 따라 주름의 크기가 달라지는 차량용 벨로우즈에 적용하기에는 부족함이 있다. 본 연구에서는 유한요소 해석기법을 이용하여 차량용 벨로우즈의 모델링 기법을 제시하고, 그 정확성을 실험결과와 비교하여 입증하였다.

• Journal of Advanced Marine Engineering and Technology
• /
• 제38권6호
• /
• pp.639-647
• /
• 2014

지구 온난화와 화석 연료 고갈로 인해 $CO_2$ 저감과 효율 상승을 동시에 만족하는 기술 개발이 요구된다. 배기 열 회수 기술은 두 가지를 모두 만족할 수 있는 대표적인 기술이다. 본 연구는 배기 열 회수 장치를 위한 세 가지 형식의 증발기용 열교환기를 배기관에 설치하여 실험 및 분석하였다. 고속최대부하에서 판형 열교환기의 배압이 가장 높아지고 실린더 최고 압력이 낮아지며 일산화탄소 배출량도 증가하였다. 또한 고속에서 배압이 2배 이상 증가하며 연료소비율이 2% 증가되어 열교환기 중 가장 높은 증가량을 나타내었다. 핀 튜브 열교환기는 전반적으로 배기 배출물이 적게 배출되고 연료소비율도 가장 적게 나타났다. 쉘 앤 튜브는 판형과 핀 튜브 성능의 중간정도이다. 엔진에 미치는 영향으로만 판단할 때 핀 튜브 열교환기가 배기 열 회수에 가장 적합한 열교환기로 판단된다.

• 한국화재소방학회논문지
• /
• 제30권1호
• /
• pp.63-73
• /
• 2016

본 논문은 초고층건물 화재 시 외기바람의 풍속, 풍향 조건이 기계배연시스템의 배연성능에 미치는 영향을 분석하였으며, 차원해석을 통한 축소모델 설계와 CFD 수치해석을 이용하여 영향을 정량적으로 평가하였다. 해석 결과, 축소모델의 외기풍속 5 m/s(실 외기풍속은 약 16 m/s), 풍향 ${\theta}=5^{\circ}$의 조건의 경우 배연풍속이 최대 약 17% 감소함을 보였으며, 외기풍향 각도 ${\theta}=25^{\circ}$ 이하의 조건에서는 기계배연시스템의 배출풍량을 크게 감소시켜 화재시 배연성능이 저하될 수 있는 것으로 평가되었다.

• 드라이브 ㆍ 컨트롤
• /
• 제20권3호
• /
• pp.15-24
• /
• 2023

The aim of this study was to measure and evaluate the exhaust emission factors of agricultural tractors. Engine characteristics and three exhaust emissions (CO, NO_x, PM) were collected under actual agricultural operating conditions. Experiments were performed on idling, driving, plow tillage, and rotary tillage. The load factor (LF) was calculated using the collected engine data, and the emission factor was analyzed using the LF and exhaust emissions. The engine characteristics and exhaust emissions were significantly different for each working condition, and in particular, the LF was significantly different from the currently applied 0.48 LF. The data distribution of exhaust emissions was different depending on the engine speed. In some conditions, the emission factor was higher than the exhaust emission standards. However, since most emission limit standards are values calculated using an engine dynamometer, even if the emission factor measured under actual working conditions is higher, it cannot be regarded as wrong. It is expected that the results of this study can be used for the inventory construction of a calculation for domestic agricultural machinery emissions in the future.

• 한국터널지하공간학회 논문집
• /
• 제5권4호
• /
• pp.389-400
• /
• 2003

본 연구는 지하철방재대책의 일환으로 터널구간에 설치된 환기기의 제연절환 운전모드 및 승강장 선로부 환기장치를 포함한 6종류의 제연운전모드를 대상으로 승강장에 정차된 열차화재 시나리오에 따라 3차원 실시간 화재 시뮬레이션을 수행하여 제연방식별 열 및 연기전파특성을 규명함으로서, 승강장에서 열차 화재 발생시, 승객이 안전하게 최적 대피가 가능한 환기기의 제연절환 조합운전의 도출을 목표로 한다.

• Journal of Advanced Marine Engineering and Technology
• /
• 제21권5호
• /
• pp.491-502
• /
• 1997

This paper describes a theoretical and exprimental investigation of the pressure - time histories of some basic internal combustion engine exhaust systems. The program package is utilized the method of characteristics to solve the general equations of one - dimensional unsteady gas flow. This analysis is then combined with boundary models, based on quasi - steady flow approach, to give a complete treatment of the flow behavior in the exhaust system. Using a rotary valve exhaust simulator, experimental pressure - time histories were obtained. The predictions are com¬pared with measured results and show a high degree of correlation in amplitude and phasing.

• 동력기계공학회지
• /
• 제19권4호
• /
• pp.82-88
• /
• 2015

The purpose of this study is to investigate the effect of the impinging plate on combustion process in Diesel engine. Especially, the variation of exhaust emission and engine performance by the change of fuel injection timing and fuel injection pressure between the trial engine with impinging plate and the prototype engine were examined. The nitrogen oxide concentration of the trial engine decreased more than 50% compared to the prototype engine, however, smoke concentration of the trial engine indicated higher degree than the prototype engine. The smoke concentration, fuel consumption rate and exhaust gas temperature decreased as the fuel injection timing become faster, whereas the nitrogen oxide concentration decreased as the fuel injection timing is retarded. The nitrogen oxide concentration, fuel consumption rate and exhaust gas temperature decreased as the fuel injection pressure become lower. But smoke concentration decreased as the fuel injection pressure become higher.

• 한국대기환경학회지
• /
• 제11권2호
• /
• pp.153-162
• /
• 1995

As exhaust emission standards for new passenger cars amended in 1987 have become more stringent, vehicle manufacturers have employed three-way catalyst in order to meet these requirements. The purpose of this study was to gather informations on new emission control systems in customer use for in-use vehicles from the 1987 through 1992 model years were capable of achieving low exhaust emission levels although high levels do occur due to defects, deterioration or maladjustments with the emission control equipment. The vehicles with closed loop electronic control fuel injection system emitted low exhaust emission, but the carburetor control system equipped vehicles emitted high exhaust emissions and the high mileage vehicles exhibited higher average emissions than low mileage vehicles. It was also found that the useful life of 80, 000km is very important to maintain the low emission levels within customer service period.