• 한국전기전자재료학회논문지
• /
• 제26권8호
• /
• pp.608-613
• /
• 2013

In this paper, the low-temperature sintering of $TiO_2$ is approached to solve the problem of high temperature sintering which decreases the interconnection between particles or between substrate and particle. $TiO_2$ paste is prepared with Titanium (IV) isopropoxide as the precursor material and calcinate at different conditions (low temperature). In the results, since the changing of temperature and time of sintering, crystalline phase do not change and the intensities of anatase, rutile phase are higher. At $110^{\circ}C$, 7 h sintering condition, crystalline size of anatase and rutile phase are the smallest which are 13.07 and 17.47 nm, respectively. In addition, the highest zeta potential is about 32.77 mV and the repulsive force increases thus leading to the best of the dispersion characteristics between $TiO_2$ particles. Futhermore, DSSCs at that condition exhibits the highest efficiency with the values of $V_{oc}$, $J_{sc}$, FF and ${\eta}$ are 0.69 V, $8.60mA\;cm^{-2}$, 67.93% and 4.06%, respectively.

• 한국수소및신에너지학회논문집
• /
• 제3권2호
• /
• pp.25-33
• /
• 1992

With the aim to obtain $TiO_2$ films with an increased photorespones and absorbance in the visible region of the solar spectrum, the direct oxidation of titanium alloys were performed. In this study, $Ti-Ga_2O_3$ alloy was prepared by mixing, pressing and arc melting of appropriate amounts of titanium and $Ga_2O_3$ powder. Electrochemical measurements were performed in three electrode cell using electrolyte of 1M NaOH solution. The oxide films on $Ti-Ga_2O_3$ alloy was composed of $Ti_2O$, TiO, $TiO_2$, $Ga_2TiO_5$. The free energy efficiency (${\eta}e$) of $Ti-Ga_2O_3$ oxide films had 0.8~1.3 % and were increased with the increase of $Ga_2O_3$ content up to 10wt %. The onset potential ($V_{on}$) had -0.8V~0.9V ranges and were shifted to anodic direction with the increase of $Ga_2O_3$ content. The spectral response of Ti-$Ga_2O_3$ oxides were similar to the response of the $TiO_2$ and their $E_g$ were observed to 2.90~3.0eV. Variations of onset potential($V_{on}$) associated with electrolyte pH were -59mV/pH. This probably reflects the nature of the bonding of $OH^-$ ion to the $TiO_2$ surface, a common phenomena in the transition-metal oxides.

• Restorative Dentistry and Endodontics
• /
• 제12권1호
• /
• pp.39-49
• /
• 1986

The purpose of this study was to observe characteristic properties through the polarization curves and SEM images from 4 different types of amalgam obtained by using the potentiostats (Princeton EG & G) & SEM (Jeol/35), and to investigate the degree of corrosion on the oxidation peak of the each phase of amalgam. After each amalgam alloy and Hg was triturated as the direction of the manufacturer by means of the mechanical amalgamator (Shofu Co.), the triturated mass was inserted into the cylindrical metal mold which was 12mm in diameter and 10.0mm in height and was condensed by using routine manner. The specimen was removed from the mold and stored at room temperature for about 24 hours. The standard surface preparation was routinely carried out. Anodic polarization measurement was employed to confirm the corrosion behaviour of the amalgams in a 0.9% saline solution (P.H: 6.8-7.0) at $37^{\circ}C$. The initial rest potential (corrosion potential) was determined after 30 minutes of immersion of specimen in electrolyte, and the potential scan was begun at the point of 100mV cathodic from the corrosion potential. The scan rate was 0.17mV/sec. in the study to observe the degree of corrosion of each phase. SEI and EPMA images on the determined oxidation peaks of each amalgam were observed. The results were as follows: 1. In the four anodic polarization curves, low copper amalgams have three oxidation peaks and high copper amalgams have two oxidation peaks, -270mV, +26mV and +179mV(SEC) in the low copper lathe cut, and -300mV, +39mV and +163mV(SEC) in the low copper spherical. -4mV and +154mV(SEC) in the Dispersalloy, and +17mV and +180mV(SEC) in the Tytin as high copper amalgams. 2. ${\gamma}_2$ phase in the low copper amalgam and ${\eta}$ phase in the high copper amalgam were the most corrodible phases and Ag-Cu eutectic in high copper amalgam was the most slowly corroded phase. 3. Low copper amalgam was more susceptible in corrosion than high copper amalgam.

• 해양환경안전학회지
• /
• 제19권2호
• /
• pp.145-154
• /
• 2013

유류를 포함한 위험 유해물질(Hazardous and Noxious Substances : HNS, 이하 HNS)의 물동량이 증가하는 추세에 있음에도 불구하고 우리나라에서는 HNS 해상운송 중에 일어난 사고의 분석과 위험에 관한 연구가 미진하다. HNS는 형태와 종류가 다양하고, 사고발생 시 피해가 심각하게 나타나기 때문에 사고에 대한 위험도 분석과 저감방안 모색이 필요하다. 본 연구는 ETA를 통해 국내에서 발생하고 있는 HNS 해상운송사고의 전개과정을 분석하여 사고유형과 특징을 고찰하고, 시나리오별 확률과 인명피해를 산출하여 F-N curve로 표현함으로써 위험도를 평가한다. 또한 Risk Matrix를 이용하여 고위험군 시나리오를 선정하여 국내에 적용 가능한 현실적인 사고 저감방안을 모색한다. 연구의 결과는 충돌사고의 발생확률이 가장 높은 반면 인명위험도는 발생확률이 낮은 질식, 침몰, 폭발의 사고유형이 높은 것으로 나타났다. 이러한 인명피해를 줄이기 위해서는 기본적으로 선내에서 안전수칙 및 작업절차를 준수하는 것으로도 효과를 얻을 수 있다.

• 대한화학회지
• /
• 제55권5호
• /
• pp.733-740
• /
• 2011

Multiple regression analysis was used for the calculation of pKa values of 15 substituted benzaldoximes by using various types of descriptors as parameters. These descriptors are based on quantum mechanical treatments. They were derived by employing semi-empirical calculation represented by the PM3 model and an Abinitio method expressed by Hartree-Fock(HF) model performed at the 6-311 G(d, p) level of theory. The parameters tested for their ability to represent the variations observed in the experimental pKa(s) are atomic and structural properties including Muliken charges on the atoms of hydroxyl group and C=N bond, the angle $C_6-C_1-C_7$, and length of O-H bond. Molecular properties are also used like energies of HOMO and LUMO, hardness(${\eta}$), chemical potential(${\mu}$), total energy(TE), dipole of molecule(DM), and electrophilicity index(W). The relation between pKa values and each of these parameters of the studied compounds is investigated. Depending on these relations, two sets of parameters were constructed for comparison between the PM3 and HF methods. The results obtained favor the Abinitio method for such applications although both models proved to have high predictive power and have sufficient reliability to describe the effect of substituents on pKa values of benzaldoxime compounds under consideration which is clear from the values of correlation coefficient $R^2$ obtained and the consistency between the experimental and the calculated values.

• 한국재료학회지
• /
• 제20권9호
• /
• pp.483-487
• /
• 2010

To fabricate $TiO_2$ nanoparticle-based dye sensitized solar cells (DSSCs) at a low-temperature, DSSCs were fabricated using hydropolymer and ZnO nanoparticles composites for the electron transport layer around a low-temperature ($200^{\circ}C$). ZnO nanoparticle with 20 nm and 60 nm diameter were used and Pt was deposited as a counter electrode on ITO/glass using an RF magnetron sputtering. We investigate the effect of ZnO nanoparticle concentration in hydropolymer and ZnO nanoparticle solution on the photoconversion performance of the low temperature fabricated ($200^{\circ}C$) DSSCs. Using cis-bis(isothiocyanato)bis(2,20 bipyridy1-4,40 dicarboxylato) ruthenium (II) bis-tetrabutylammonium (N719) dye as a sensitizer, the corresponding device performance and photo-physical characteristics are investigated through conventional physical characterization techniques. The effect of thickness of the ZnO photoelectrode and the morphology of the ZnO nanoparticles with the variations of hydropolymer to ZnO ratio on the photoconversion performance are also investigated. The morphology of the ZnO layer after sintering was examined using a field emission scanning electron microscope (FE-SEM). 60 nm ZnO nanoparticle DSSCs showed an incident photon-to-current conversion efficiency (IPCE) value of about 7% higher than that of 20 nm ZnO nanoparticle DSSCs. The maximum parameters of the short circuit current density ($J_{sc}$), the open circuit potential ($V_{oc}$), fill factor (ff), and efficiency ($\eta$) in the 60 nm ZnO nanoparticle-based DSSC devices were 4.93 mA/$cm^2$, 0.56V, 0.40, and 1.12%, respectively.

• Journal of Microbiology and Biotechnology
• /
• 제23권2호
• /
• pp.161-166
• /
• 2013

At present, acetylcholinesterase (AChE) inhibitors are the first group of drugs to treat mild to moderate Alzheimer's disease (AD). Although beneficial in improving cognitive and behavioral symptoms, the effectiveness of AChE inhibitors has been questioned since they do not delay or prevent neurodegeneration in AD patients. Therefore, in the present study, in order to develop new and effective anti-AD agents from lichen products, both the AChE inhibitory and the neuroprotective effects were evaluated. The AChE inhibitory assay was performed based on Ellman's reaction, and the neuroprotective effect was evaluated by using the MTT method on injured PC12 cells. One AChE inhibitor ($IC_{50}$ = 27.1 ${\mu}g/ml$) was isolated by means of bioactivity-guided isolation from the extract of lichen-forming fungus Cladonia macilenta, which showed the most potent AChE inhibitory activity in previous screening experiment. It was then identified as biruloquinone by MS, and $^1H$- and $^{13}C$-NMR analyses. The inhibitory kinetic assay suggested that biruloquinone is a mixed-II inhibitor on AChE. Meanwhile, biruloquinone improved the viability of the $H_2O_2$- and ${\beta}$-amyloid-injured PC12 cells at 1 to 25 ${\mu}g/ml$. The protective effects are proposed to be related to the potent antioxidant activities of biruloquinone. These results imply that biruloquinone has the potential to be developed as a multifunctional anti- AD agent.

• 한국진공학회:학술대회논문집
• /
• 한국진공학회 2016년도 제50회 동계 정기학술대회 초록집
• /
• pp.388-388
• /
• 2016

Chemical mist deposition (CMD) of poly(3,4-ethylenedioxythiophene):poly(styrene sulfonate) (PEDOT:PSS) was investigated with cavitation frequency f, solvent, flow rate of nitrogen, substrate temperature $T_s$, and substrate dc bias $V_s$ as variables for efficient PEDOT:PSS/crystalline (c-)Si heterojunction solar cells (Fig. 1). The high-speed camera and differential mobility analysis characterizations revealed that average size and flux of PEDOT:PSS mist depend on f, solvent, and $V_s$. The size distribution of mist particles including EG/DI water cosolvent is also shown at three different $V_s$ of 0, 1.5, and 5 kV for a f of 3 MHz (Fig. 2). The size distribution of EG/DI water mist without PEDOT:PSS is also shown at the bottom. A peak maximum shifted from 300-350 to 20-30 nm with a narrow band width of ~150 nm for PEDOT:PSS solution, whose maximum number density increased significantly up to 8000/cc with increasing $V_s$. On the other hand, for EG/water cosolvent mist alone, the peak maximum was observed at a 72.3 nm with a number density of ~700/cc and a band width of ~160 nm and it decreased markedly with increasing $V_s$. These findings were not observed for PEDOT:PSS/EG/DI water mist. In addition, the Mie scattering image of PEDOT:PSS mist under white bias light was not observed at $V_s$ above 5 kV, because the average size of mist became smaller. These results imply that most of solvent is solvated in PEDOT:PSS molecule and/or solvent is vaporized. Thus, higher f and $V_s$ generate preferentially fine mist particle with a narrower band width. Film deposition occurred when $V_s$ was impressed on positive to a c-Si substrate at a Ts of $30-40^{\circ}C$, whereas no deposition of films occurred on negative, implying that negatively charged mist mainly provide the film deposition. The uniform deposition of PEDOT:PSS films occurred on textured c-Si(100) substrate by adjusting $T_s$ and $V_s$. The adhesion of CMD PEDOT:PSS to c-Si enhanced by $V_s$ conspicuously compared to that of spin-coated film. The CMD PEDOT:PSS/c-Si solar cell devices on textured c-Si(100) exhibited a ${\eta}$ of 11.0% with the better uniformity of the solar cell parameters. Furthermore, ${\eta}$ increased to 12.5% with a $J_{sc}$ of $35.6mA/cm^2$, a $V_{oc}$ of 0.53 V, and a FF of 0.67 with an antireflection (AR) coating layer of 20-nm-thick CMD molybdenum oxide $MoO_x$ (n= 2.1) using negatively charged mist of 0.1 wt% 12 Molybdo (VI) phosphoric acid n-Hydrate) $H_3(PMo_{12}O_40){\cdot}nH_2O$ in methanol. CMD. These findings suggest that the CMD with negatively charged mist has a great potential for the uniform deposition of organic and inorganic on textured c-Si substrate by adjusting $T_s$ and $V_s$.

• 한국화재소방학회논문지
• /
• 제15권1호
• /
• pp.84-92
• /
• 2001

현대 사회에 있어서 인구 과밀화와 더불어 대도시의 사회기반시설(SOC)증가에 따른 화학물질 사용시설의 중대사고의 경향이 높아져 가고 있다. 기존 위해·위험시설의 안전사고의 문제점과 더불어 신규 위해·위험시설물의 증가에 따른 안전사고의 심각성을 낮추기 위해 필요한 노력을 하지 않으면 안된다. 선진국에서는 산업시설 그리고 지역사회의 전문위원회가 잠재적인 위해 산업의 사고에 대한 off site 및 on site의 피해 심각성에 대한 평가와 이에 대한 적절한 조언 및 대책을 강구하고 있다. 따라서 본 연구에서는 국내의 위해·위험시설에 대한 안전도 수용기준 성립을 위하여 첫째, 영국 HSE(Heath & Safety Executive)의 QRA(Quantified Risk Assessment)와 Matrix of Risk of Evaluated Sources of Hazard를 적용한 사회적 위험성 평가 방법과 둘째, FTA(Fault Tree Analysis) 또는 ETA(Event Tree Analysis) 등 정량적인 사고 발생 확률과 시뮬레이션 및 계산식을 통해 국내 임의의 지역에 대하여(서울시 위해·위험시설)사고 피해 정도의 개인적 위험성을 평가, 적용함으로서 기존 시설 또는 신설 부지 개발을 위한 제한시 포괄적 안전도 수용기준(수용가능성) 여부를 판별하고자 한다.