• 한국수자원학회:학술대회논문집
• /
• 한국수자원학회 2008년도 학술발표회 논문집
• /
• pp.1295-1299
• /
• 2008

Soil erosion is a natural process and has been occurring in most areas in the watershed. However, accelerated soil erosion rates have been causing numerous environmental impacts in recent years. To reduce soil erosion and sediment inflow into the water bodies, site-specific soil erosion best management practices (BMPs) need to be established and implemented. The most commonly used soil erosion model is the Universal Soil Loss Equation (USLE), which have been used in many countries over 30 years. The Sediment Assessment Tool for Effective Erosion Control (SATEEC) ArcView GIS system has been developed and enhanced to estimate the soil erosion and sediment yield from the watershed using the USLE input data. In the last decade, the Soil and Water Assessment Tool (SWAT) model also has been widely used to estimate soil erosion and sediment yield at a watershed scale. The SATEEC system estimates the LS factor using the equation suggested by Moore and Burch, while the SWAT model estimates the LS factor based on the relationship between sub watershed average slope and slope length. Thus the SATEEC and SWAT estimated soil erosion values were compared in this study. The differences in LS factor estimation methods in the SATEEC and SWAT caused significant difference in estimated soil erosion. In this study, the difference was -51.9%(default threshold)$\sim$-54.5%(min. threshold) between SATEEC and non-patched SWAT, and -7.8%(default threshold)$\sim$+3.8%(min. threshold) between SATEEC and patched SWAT estimated soil erosion.

• 한국농공학회논문집
• /
• 제50권1호
• /
• pp.3-12
• /
• 2008

Soil erosion is a natural process and has been occurring in most areas in the watershed. However, accelerated soil erosion rates have been causing numerous environmental impacts in recent years. To reduce soil erosion and sediment inflow into the water bodies, site-specific soil erosion best management practices(BMPs) need to be established and implemented. The most commonly used soil erosion model is the Universal Soil Loss Equation(USLE), which have been used in many countries over 30 years. The Sediment Assessment Tool for Effective Erosion Control(SATEEC) ArcView GIS system has been developed and enhanced to estimate the soil erosion and sediment yield trom the watershed using the USLE input data. In the last decade, the Soil and Water Assessment Tool(SWAT) model also has been widely used to estimate soil erosion and sediment yield at a watershed scale. The SATEEC system estimates the LS factor using the equation suggested by Moore and Burch, while the SWAT model estimates the LS factor based on the relationship between sub watershed average slope and slope length. Thus the SATEEC and SWAT estimated soil erosion values were compared in this study. The differences in LS factor estimation methods in the SATEEC and SWAT caused significant difference in estimated soil erosion. In this study, the difference was -51.9%(default threshold)${\sim}-54.5%$(min. threshold) between SATEEC and non-patched SWAT, and -7.8%(default threshold)${\sim}+3.8%$(min. threshold) between SATEEC and patched SWAT estimated soil erosion.

• 한국분말재료학회지
• /
• 제27권3호
• /
• pp.210-218
• /
• 2020

A T-800 (Co-Mo-Cr) coating material is fabricated using Co-Mo-Cr powder feedstock and laser cladding. The microstructure and melted Al erosion properties of the laser-cladded T-800 coating material are investigated. The Al erosion properties of the HVOF-sprayed MoB-CoCr and bulk T-800 material are also examined and compared with the laser-cladded T-800 coating material. Co and lave phases (Co₂MoCr and Co₃Mo₂Si) are detected in both the laser-cladded T-800 coating and the bulk T-800 materials. However, the sizes of the lave phases are measured as 7.9 ㎛ and 60.6 ㎛ for the laser-cladded and bulk T-800 materials, respectively. After the Al erosion tests, the erosion layer thicknesses of the three materials are measured as 91.50 ㎛ (HVOF MoB-CoCr coating), 204.83 ㎛ (laser cladded T-800), and 226.33 ㎛ (bulk T-800). In the HVOF MoB-CoCr coating material, coarse cracks and delamination of the coating layer are observed. On the other hand, no cracks or local delamination of the coating layer are detected in the laser T-800 material even after the Al erosion test. Based on the above results, the authors discuss the appropriate material and process that could replace conventional bulk T-800 materials used as molten Al pots.

• 한국해안·해양공학회논문집
• /
• 제20권6호
• /
• pp.611-620
• /
• 2008

해안침식의 과정은 여러가지 원인이 복합적으로 작용하여 발생되는 경우가 많다. 일반적으로 해안침식은 표사이동의 평형파괴, 호안의 건설 및 이안류 발생 등과 같은 다양한 원인으로부터 야기된다. 따라서, 이러한 해안침식현상을 제어하기 위해서는 해안침식을 야기시키는 주된 원인을 정확히 파악하는 것이 가장 우선시 되어야 하고, 그 주원인에 대한 대책을 수립해야만 한다. 본 연구에서는 파랑이 탁월한 동해안의 전촌-나정해안을 대상으로 표사이동에 따른 침식현상을 검토하고 침식의 주원인을 도출하고자 하였다. 원인분석방법으로는 현장관측자료, 항공사진분석 및 수치모형실험을 이용하였다. 그 결과 대상해역에 있어서 해안침식의 주원인은 전촌, 나정항의 건설 및 호안건설에 의한 것임을 확인할 수 있었다.

• 한국수자원학회:학술대회논문집
• /
• 한국수자원학회 2011년도 학술발표회
• /
• pp.17-17
• /
• 2011

As a method of countermeasure to bed degradation and armoring phenomena of bed material in the downstream area of dam reservoirs, sediment augmentation (replenished sediment) has been carried out in many Japanese rivers. In general, bed of the replenished sediment site is composed of rocks, because the site is located in the downstream area of the dams and sediment supply is very small. Bed deformation process has been researched by many researchers. As a method of countermeasure to bed degradation and armoring phenomena of bed material in the downstream area of dam reservoirs, sediment augmentation (replenished sediment) has been carried out in many Japanese rivers. In general, bed of the replenished sediment site is composed of rocks, because the site is located in the downstream area of the dams and sediment supply is very small. Bed deformation process has been researched by many researchers. However, most of them can treat movable bed only and cannot be applied to the bed deformation process of sediment on rocks. If the friction angle between the sediment and the bed surface is assumed to be the same as the friction angle between the sediment and the sediment, sediment transport rate must be smaller without sediment deposition layer on the rocks. As a result, the reproduced bed geometry is affected very well. In this study, non-equilibrium transport process of non-cohesive sediment on rigid bed is introduced into the horizontal two dimensional bed deformation model and the model is applied to the erosion process of replenished sediment on rock in the Nakagawa, Japan. Here, the Japanese largest scale sediment augmentation has been performed in the Nakagawa. The results show that the amounts of the eroded sediment and the remained sediment reproduced by the developed numerical model are $56300m^3$ and $26800m^3$, respectively. On the other hand, the amounts of the eroded sediment and the remained sediment measured in the field after the floods are $56600m^3$ and $26500m^3$, respectively. The difference between the model and field data is very small. Furthermore, the bed geometry of the replenished sediment after the floods reproduced by the developed model has a good agreement with the measured bed geometry after the floods. These results indicate that the developed model is able to simulate the erosion process of replenished sediment on rocks very well. Furthermore, the erosion speed of the replenished sediment during the decreasing process of the water discharge is faster than that during the increasing process of the water discharge. The replenished sediment is eroded well, when the top of the replenished sediment is covered by the water. In general, water surface level is kept to be high during the decreasing process of the discharge during floods, because water surface level at the downstream end is high. Hence, it is considered that the high water surface level during the decreasing process of the water discharge affects on the fast erosion of the replenished sediment.

• 한국윤활학회:학술대회논문집
• /
• 한국윤활학회 1998년도 제27회 춘계학술대회
• /
• pp.139-145
• /
• 1998

This paper addresses the R-curve properties, wear resistance, and erosion resistance of the two silicon carbide ceramics with different microstructures, i.e. , fine grained SiC and in situ-toughened SiC(IST SIC). Fine grained SiC exhibits a relatively flat R-curve behavior whereas the IST SiC exhibits a increasing R-curve behavior. The increasing R-curve behavior in IST SiC is attributed to relatively weak grain boundaries. The rate of material removal during wear tests and erosion tests was higher for IST SiC than that for fine grained SiC. This is attributed to the weaker grain boundaries in IST SiC than that in fine grained SiC. It is implied that fracture toughness in short crack regime should be taken into consideration in the interpretation of the microscopical material removal process. We show that the higher the strength of grain boundaries is, the higher wear and erosion resistances are.

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 2005년도 추계학술대회 논문집
• /
• pp.488-491
• /
• 2005

Abrasive Jet Micromachining (AJM) is a process that uses high pressure air with micron-sized particles to erode a substrate. It has been considered as the most economic and appropriate technique to pattern glass surfaces for the flat panel applications. To accelerate the industrialization of AJM, it is necessary to understand the erosion mechanisms thoroughly. Thus, this paper introduces a new method to model the erosion mechanism in AJM. The model is developed by using the concept of the accumulation of the microdeformation caused by each particle. And this paper proposes the model added the effects of second impact. The developed model is used to simulate the erosion profile, and is compared with the model considered only first impact. It can be concluded that the proposed model predicts the erosion profile more accurately.

• Tribology and Lubricants
• /
• 제34권5호
• /
• pp.175-182
• /
• 2018

Accumulation of coal ash at the boiler wall reduces combustion and fuel efficiency. The design of a wall blower is important to effectively remove coal ash. We present numerical results for the removal of coal ash from boiler walls of domestic coal-fired power plants, associated with the computational fluid dynamics for the flow from spray nozzle to boiler wall. The numerical model simulates an erosion process in which the multiphase fluid comprising saturated vapor and fluid water is sprayed from the nozzle, and the water particles impact the boiler wall. We adopt the Finnie erosion model for water particles. We obtain the erosion rate density as a function of nozzle angle and its injection angle. As excessive coal ash removal usually induces damage to the boiler wall, the removal operation typically focuses on a large area with uniform depth rather than the maximum removal of coal ash at a specific location. In order to estimate the removal performance of the wall blower nozzle considering several functionality and reliability factors, we evaluate the optimal injection and nozzle angles with respect to the biggest cumulative and highest erosion rates, as well as the widest range and lowest standard deviation of the erosion rate distribution.

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 2001년도 춘계학술대회 논문집
• /
• pp.1117-1120
• /
• 2001

Chemical mechanical planarization(CMP) has emerged as the planarization technique of choice in both front-end and back-end integrated circuit manufacturing. Conventional CMP process utilize a polyurethane polishing pad and liquid chemical slurry containing abrasive particles. There have been serious problems in CMP in terms of repeatability and defects in patterned wafers. Since IBM's official announcement on Copper Dual Damascene(Cu2D) technology, the semiconductor world has been engaged in a Cu2D race. Today, even after~3years of extensive R&D work, the End-of-Line(EOL) yields are still too low to allow the transition of technology to manufacturing. One of the reasons behind this is the myriad of defects associated with Cu technology. Especially, dishing and erosion defects increase the resistance because they decrease the interconnection section area, and ultimately reduce the lifetime of the semiconductor. Methods to reduce dishing & erosion have recently been interface hardness of the pad, optimization of the pattern structure as dummy patterns. Dishing & erosion are initially generated an uneven pressure distribution in the materials. These defects are accelerated by free abrasive and chemical etching. Therefore, it is known that dishing & erosion can be reduced by minimizing the abrasive concentration. Minimizing the abrasive concentration by using Ce$O_2$ is the best solution for reducing dishing & erosion and for removal rate. This paper introduce dishing & erosion generating mechanism and a method for developing a semi-rigid abrasive pad to minimize dishing & erosion during CMP.

• 한국정밀공학회지
• /
• 제18권12호
• /
• pp.192-199
• /
• 2001

Chemical mechanical planarization (CMP) has emerged as the planarization technique of choice in both front-end and back-end integrated circuit manufacturing. Conventional CMP process utilize a polyurethane polishing pad and liquid chemical slurry containing abrasive particles. There hale been serious problems in CMP in terms of repeatability and deflects in patterned wafers. Especial1y, dishing and erosion defects increase the resistance because they decrease the interconnection section area, and ultimately reduce the lifetime of the semiconductor. Methods to reduce dishing & erosion have recently been interface hardness of the pad, optimization of the pattern structure as dummy patterns. Dishing & erosion are initially generated an uneven pressure distribution in the materials. These defects are accelerated by free abrasives and chemical etching. Therefore, it is known that dishing & erosion can be reduced by minimizing the abrasive concentration. Minimizing the abrasive concentration by using CeO$_2$is the best solution for reducing dishing & erosion and for removal rate. This paper introduce dishing & erosion generating mechanism and a method fur developing a semi-rigid abrasive pad to minimize dishing & erosion during CMP.