• 한국윤활학회:학술대회논문집
• /
• 한국윤활학회 1998년도 제28회 추계학술대회
• /
• pp.67-74
• /
• 1998

Two kinds of polished and unpolished freestanding films prepared by DC plasma CVD method were impacted by SiC particles to understand erosion mechanism. Erosion damage caused by solid impact was characterized by surface profilometer, scanning electron microscopy and Raman spectroscopy. Gradually decrease of surface roughness and sharp reduction of crystallinity for unpolished CVD films were observed with increasing erosion time. It was found that smaller grains of the diamond were removed in early stage of erosion process and larger grains were eroded with further impingement. By introduction of re-growth method on polished diamond, further understanding of erosion mechanism was achieved. Most of the surface fractures were initiated at the grain boundary.

• International Journal of Precision Engineering and Manufacturing
• /
• 제9권2호
• /
• pp.11-17
• /
• 2008

Critical erosion kinetic energy models for radial/median cracks and lateral cracks in a workpiece are established in this study. We used experimental results to demonstrate that the fracture erosion resistance and erosion machining number could be used to evaluate the brittle fracture resistance and machinability of a workpiece. Erosion kinetic energy models were developed to predict brittle fracture and ductile shear, and a critical erosion kinetic energy model was developed to predict the transition from brittle fracture to ductile shear. These models were verified experimentally.

• 아시안잔디학회지
• /
• 제10권1호
• /
• pp.49-59
• /
• 1996

This report is researched on the cause and mechanism of soil erosion in comparison among Kwangnung, Mt. Kaya, Mt. Chili, and Mt. Soorak by physical and chemical analyses of their for- est soils. Clay, silt, and fine sand of Mt. Soorak are far less than those of Mt. Chili, Mt. Kaya, and Kwangnung area while coarse sand is very high level. The clay ratio of soil at Mt. Soorak is the most high level in comparison with that of other area. Denudation at Mt. Soorak, therefore, is cause of erosion by the result of transportation of soil particles. The eroding velocity increase for larger particle size and stronger cohesion between soil particles. Very fine sand, silt, and clay can be present in suspension near the bottom and the size of the particles in suspension depends upon the velocity of the current near the bottom and the roughness of the bottom. Key words: Theoretical analyses, Soil erosion and conservation, Forest soils.

• 한국진공학회:학술대회논문집
• /
• 한국진공학회 2011년도 제40회 동계학술대회 초록집
• /
• pp.16-16
• /
• 2011

Plasmas in saline solutions receive considerable attention in recent years. How the operating parameters influence the plasma characteristics and how the electrode erosion occurs have been topics that require further study. In the first part of this talk, the effect of the frequency on the plasmas characteristics in saline solution driven by 50~1000 Hz AC power will be presented. Two distinct modes, namely bubble and jetting modes, are identified. The bubble mode occurs under low frequencies. In this mode, one mm-sized bubble is tightly attached to the electrode tip and oscillates with the applied voltage. With an increase in the frequency, it shows the jetting mode, in which many smaller bubbles are continuous formed and jetted away from the electrode surface. Multiple mechanisms that are potentially responsible to such a change in bubble dynamics have been proposed and the dominant mechanism is identified. From the Stark broadening of the hydrogen optical emission line, electron densities in both modes are estimated. It shows clearly that the driving frequency greatly influences the bubble dynamics, which in turn alters the plasma behavior. In the second part, the study of the erosion of a tungsten electrode immersed in saline solution under conditions suitable for bio-medical applications is presented. The electrode is immersed in 0.1 M saline solution and is positively or negatively biased using a DC power source up to 600 V. It is identified that when the electrode is positively biased, erosion by the surface electrolytic oxidation is the dominant mechanism with an applied voltage below 150 V. An increase in the applied voltage leads to the formation of the plasma and the damage by the plasma and the thermal effect becomes more prominent. The formation of the gas film at the electrode surface leads to the formation of the plasma and hinders the electrolytic erosion. In the negatively-biased electrode, no electrolytic oxidation is seen and the damage is mostly likely due to the plasma erosion and the thermal effect.

• Carbon letters
• /
• 제4권3호
• /
• pp.133-139
• /
• 2003

Carbon/carbon composites are ideal candidates for a number of aerospace applications including structural materials for advanced vehicles, leading edges, structures of re-entry and hypersonic vehicles and propulsion systems. One serious defect for such application of the carbon/carbon composites is their poor oxidation resistance in high temperature oxidizing environments. SiC coating was employed to protect the composites from oxidation. It is mechanically and chemically stable under extreme thermal and oxidative environments, provides good adhesion to the substrate, and offers good thermal shock resistance. The SiC layer on the nozzle machined from the carbon/carbon composites was formed by pack-cementation method. Then, erosion characteristic of SiC coated carbon/carbon nozzle was examined by combustion test using a liquid rocket motor. The erosion rates were measured as function of combustion pressure, ratio of oxygen to fuel, combustion time, density of the composites and geometry of reinforced carbon fibre in the composites. The morphology change of the composites after combustion test was investigated using SEM and erosion mechanism also was discussed.

• Journal of Advanced Marine Engineering and Technology
• /
• 제28권2호
• /
• pp.332-337
• /
• 2004

The use of gas absorption refrigeration machine has considerably increased because of the shortage of the electric power in the summer and the regulation of freon refrigerant. Gas absorption refrigeration machine consists of a condenser, a heat exchanger. supplying pipes, a radiator etc, This system is likely to be corroded by acid. dissolved oxygen and gases, Cavitation erosion-corrosion by flow velocity of cooling water may happen in absorption refrigeration machine. In these cases. erosion and corrosion occur simultaneously. Then, it makes a serious damage with synergy effect. Therefore, this paper was studied on the cavitation damage of cupronickel(70/30) tube for gas absorption refrigeration machine, In the $30^{\circ}C$ tap water, linear polarization test and anodic polarization test were carried out for copper(C1220T-OL) and cupronickel(70/30) tube. Also, cavitation erosion-corrosion behavior of cupronickel (70/30) tube was considered, The main results are as following: (1) In the linear test, the corrosion current density of cupronickel(70/30) is higher than that of copper. (2) The erosion-corrosion rate of cupronickel(70/30) displayed later tendency than that of copper by vibratory cavitation in cooling water. (3) In cooling water, the progress mechanism of erosion-corrosion rate of copper and cupronickel(70/30) follows a pattern of incubation, acceleration, attenuation and a steady state period.

• 한국표면공학회지
• /
• 제34권6호
• /
• pp.575-584
• /
• 2001

Erosion due to abrasive particles contained in gas streams from boilers has been emerged as a significant problem in the coal fired power plants. Particle erosion accounted for approximately 50% of boiler failures and especially flyash erosion was responsible for 20~30% of emergency boiler shutdowns. Particularly, because of the high ash loading and high velocity, most erosion occurs in the boiler tubes and economiser tube bank where the direction of the gas stream changes to $180^{\circ}$ .In this study, a high temperature particle erosion tester was used to evaluate erosion rate in a simulated environment. The erosion parameters such as erosion temperature, particle impact angle, particle velocity and various particle size were changed. Flyash is the combustion product of the pulverized coal, where size is ranging from 1 to $200\mu\textrm{m}$. Flyash composed of mainly SiO$_2$, $A1_2$$_O3$, and $Fe_2$$O_3$has dense spherical particles and irregular particles containing numerous pores and cavities. From the erosion tests at various conditions, the maximum erosion was experienced at impact angles of $30^{\circ}$ to $60^{\circ}$ In addition, erosion rate increased in proportional to velocity and temperature. And from the observation of the eroded surfaces, it was also concluded that 304 stainless steel was mainly eroded by extrusion-forging at high impact angle ($90^{\circ}$) and by microcutting mechanism at low impact angles ($30^{\circ}$ and $45^{\circ}$).

• 한국해안해양공학회지
• /
• 제14권4호
• /
• pp.247-256
• /
• 2002

동해안에 위치한 대부분의 중소어항은 주로 백사장 주위에 건설되어져 있으며, 이러한 어항 구조물은 인근 백사장의 침식에 중요한 영향을 끼쳐왔다. 이와 같은 문제를 해결하기 위해서는 우선, 사전예측 및 해안침식현상의 정확한 재현을 통해 그 원인을 파악하고검증할 필요가 있다. 아울러 대상해안에 적합한 침식 대책공법을 강구하여야 한다. 본 연구에서는 경제적인 측면을 고려하여 중소어항 주변해안에 실질적으로 적용할 수 있는 해안침식 대책을 도출하고, 그에 대한 방지효과를 수치시뮬레이션을 통해 검토하였다

• 수산해양기술연구
• /
• 제32권3호
• /
• pp.302-309
• /
• 1996

Cavitation erosion-corrosion implies damage to materials due to the shock pressure or shock wave that results when bubbles form and collapse at a metal surface within a liquid. If the liquids corrosive to the material, a condition typically encountered in industry, the component materials may suffer serious damage by a combination of mechanical and electrochemical attack. To suppress cavitation erosion as well as cavitation erosion-corrosion to hydraulic equipments, innovations such as the improvement in the geometric design of the equipment or the selection of suitably resistant construction materials are necessary. This study was tested by using the piezoelectric vibrator with 20kHz, 24${\mu}$m for cavitation generation. And also, the vibratory cavitation erosion-corrosion tests on commercial mild steel SS41were carried out. We carefully observed the erosion pattern and surface photography. The geometrical mechanism of pit growth, which is to be likely these processing; shallow typelongrightarrowundercut typelongrightarrowwide shallow type.

• Corrosion Science and Technology
• /
• 제20권3호
• /
• pp.143-151
• /
• 2021

In this study, optimal shot peening process conditions were investigated for improving the cavitation erosion resistance of gray cast iron under a marine environment. Shot peening was performed with variables of injection pressure and injection time. The durability was then evaluated through cavitation erosion test which was conducted according to the modified ASTM G-32 standard. The tendency of cavitation erosion damage according to shot peening process condition was investigated through weight loss rate, surface and cross-sectional analysis of the specimen before and after the test. As a result, the shot peening process condition that could minimize cavitation erosion was when the injection pressure was the lowest and when the injection time was the shortest. This was because the flake graphite exposed on the gray cast iron surface could be easily removed under such condition. Therefore, the notch effect can be prevented by surface modification. In addition, the cavitation erosion damage mechanism of gray cast iron was discussed in detail.