• KIEE International Transaction on Electrical Machinery and Energy Conversion Systems
• /
• v.5B no.1
• /
• pp.43-49
• /
• 2005

The high rate of voltage rise (dv/dt) in motor terminals caused by high-frequency switching and impedance mismatches between inverter and motor are known as the primary causes of irregular voltage distributions and insulation breakdowns on stator windings in IGBT PWM inverter-driven induction motors. In this paper, voltage distributions in the stator windings of an induction motor driven by an IGBT PWM inverter are studied. To analyze the irregular voltages of stator windings, high frequency parameters are derived from the finite element (FE) analysis of stator slots. An equivalent circuit composed of distributed capacitances, inductance, and resistance is derived from these parameters. This equivalent circuit is then used for simulation in order to predict the voltage distributions among the turns and coils. The effects of various rising times in motor terminal voltages and cable lengths on the stator voltage distribution are also presented. For a comparison with simulations, an induction motor with taps in the stator turns was made and driven by a variable-rising time switching surge generator. The test results are shown.

• KIEE International Transactions on Electrophysics and Applications
• /
• v.2C no.5
• /
• pp.246-252
• /
• 2002

Two-dimensional steady state simulations of planar type radio frequency inductively coupled plasma (RFICP) have been performed. The characteristics of RFICP were investigated in terms of power transfer efficiency, equivalent circuit analysis, spatial distribution of plasma density and electron temperature. Plasma density and electron temperature were determined from the equations of ambipolar diffusion and energy conservation. Joule heating, ionization, excitation and elastic collision loss were included as the source terms of the electron energy equation. The electromagnetic field was calculated from the vector potential formulation of ampere's law. The peak electron temperature decreases from about 4eV to 2eV as pressure increases from 5 mTorr to 100 mTorr. The peak density increases with increasing pressure. Electron temperatures at the center of the chamber are almost independent of input power and electron densities linearly increase with power level. The results agree well with theoretical analysis and experimental results. A single turn, edge feeding antenna configuration shows better density uniformity than a four-turn antenna system at relatively low pressure conditions. The thickness of the dielectric window should be minimized to reduce power loss. The equivalent resistance of the system increases with both power and pressure, which reflects the improvement of power transfer efficiency.

• Journal of the Korean Society of Manufacturing Process Engineers
• /
• v.19 no.3
• /
• pp.77-85
• /
• 2020

In this study, we proposed a method to replace the solid finite element model of the boiler membrane wall for coal-fired power plants using an equivalent shell model. The application of a bending load to the membrane wall creates greater displacement at both ends of the central portion when compared with the middle when an isotropic elastic constant is used in the shell model. This is inconsistent with the results of the solid model where the central portion is uniformly deformed. Here, we presented a method to determine the orthotropic elastic constants of the shell model in terms of bending stiffness and vibration characteristics to solve this problem. Our analysis of the orthotropic shell model showed that the error ratio was 0.9% for the maximum displacement due to the bending load, 0.3% for the first natural frequency, and 2.5% for the second natural frequency when compared with the solid model. In conclusion, a complicated boiler membrane wall composed of a large number of pipes and fins can be replaced with a simple shell model that shows equivalent bending stiffness and vibration characteristics using our proposed method.

• Journal of the Korean Institute of Illuminating and Electrical Installation Engineers
• /
• v.18 no.6
• /
• pp.230-237
• /
• 2004

In this paper the effects of inverter ripple currents to the Proton Exchange Membrane Fuel Cell Stack (PEMFCS) is analyzed by the impedance model. The proposed method employs the frequency analysis technique to derive an equivalent impedance model of the fuel cell stack and the effects of the inverter ripple current are investigated. The calculated results m then verified by means of experiments on commercially available PEMFCSs. The experimental results show that the ripple current can contribute up to 10[%] reduction in the available output power.

• Proceedings of the International Microelectronics And Packaging Society Conference
• /
• 2003.11a
• /
• pp.234-238
• /
• 2003

The LTCC bandpass filter using multilayer resonators is made of combline type and interdigital type parallel coupled-lines. The equivalent circuits of parallel coupled-lines are analysed. They are applied to make an equivalent circuit of LTCC bandpass filter using multilayer resonators. The 3-pole bandpass filter of the center frequency of 2.45GHz with 250Hz bandwidth is designed and fabricated. The simulated result of the bandpass filter are presented.

• Proceedings of the KIPE Conference
• /
• 1998.10a
• /
• pp.452-457
• /
• 1998

This paper deal with problems of leakage current, shaft voltage, bearing current, and EMI, in valiable-speed AC drives. The originating mechanism is illustrated with a high-frequency equivalent circuit. Reduction methods are classified in to six categories based on the equivalent circuit. Some experimental results show that a common-mode transformer (CMT) and a common-noise canceler (ACC) can solve the problems, which have been proposed the authors.

• Proceedings of the Korean Institute of Navigation and Port Research Conference
• /
• 1994.04a
• /
• pp.43-48
• /
• 1994

A wide band design method of an electromagnetic wave absorber using exponentially tapered ferrite which has very wide band frequency characteristics is proposed and discussed. The wide band electromagnetic wave absorber can be designed by the proposed equivalent material constants method for the regions varying spatially in the shape of ferrite. Furthemore the wide band ferrite electromagnetic wave absorbers with taper which have not only excellent reflectivity frequency characteristics but also the band width of 30MHz to 2150 or 2450MHz under the tolerance limits of -20dB reflectivity were designed.

• Journal of the Korean Institute of Navigation
• /
• v.19 no.4
• /
• pp.93-102
• /
• 1995

A design method of an electromagnetic wave absorber with ferrite fins in the second layer, which has very wide band frequency characteristics, is proposed and discussed. A theoretical model using the equivalent material constants method is adopted, assessed for its accuracy by comparision with the Hashin-Shtrikman formulas and compared with the conventional absorbers. Based on the model, a wide band electromagnetic wave absorber with excellent reflectivity frequency characteristics in frequency range of 30MHZ to 3530MHZ has been designed.

• Journal of the Korean Institute of Telematics and Electronics A
• /
• v.32A no.10
• /
• pp.35-42
• /
• 1995

In this paper the driving-condition-dependent optical transmission characteristics of an STN LCD are studied. The optical transmission properties are measured for the applied voltage waveform is varied. Also, the optimum ranges of the M signal frequency and the frame frequency are investigated. An LCD is modeled by the equivalent circuit to study the effect of the parameter variation on the frequency response.

• Journal of the Korean Institute of Navigation
• /
• v.19 no.2
• /
• pp.99-106
• /
• 1995

A wide band design method of an electromagnetic wave absorber with square ferrite cylinders in the second layer, which has very wide band frequency characteristics, is proposed and discussed. A theoretical model using the equivalent material constants method is also evaluated and proposed for its accuracy by comparison with Hashin-Shtrikman formulas. Based on the developed model, wide band electromagnetic wave absorbers with excellent reflective frequency characteristics in the frequency range of 30MHz to 3, 690MHz were designed.