• 수산해양교육연구
• /
• 제28권6호
• /
• pp.1875-1881
• /
• 2016

The wear behavior for the two types of composites, those are epoxy matrix composites filled with silica particles and aluminium matrix composites filled with SiC particles, were compared to investigate the wear mechanism for these composites. Especially, the effect of the volume fraction for the epoxy matrix composites and the particle size for the aluminium matrix composites according to the apply load and sliding velocity were investigated. Wear tests of the pin-on-disc mode were carried out and followed by scanning electron microscope observations for the worn surface. The addition of the fillers in the composites were improved the wear resistance significantly and changed the wear mechanism for the both composites. These results were identified by the observation of the worn surface after testing.

• Structural Engineering and Mechanics
• /
• 제26권1호
• /
• pp.99-109
• /
• 2007

A cracked composite specimen, comprised of an epoxy and an aluminium plate, was fractured under a tensile load. In this paper, two crack configurations were investigated. The first was an artificial center crack positioned in the epoxy plate parallel to the material interface. The other was for two edge cracks in the epoxy plate, again, parallel to the interface. A tensile test was carried out by gradually increasing the applied load and it was verified that the cracks always moved suddenly in an outward direction from the interface. The d/a ratio was gradually reduced to zero, and it was confirmed that the maximum stress intensity factor value for the artificial center crack, $K_{{\theta}{\theta}}^{max}$, approached that of an artificial interface crack,$K_{{\theta}{\theta}}^{ifc\;max}$ (where: 2a is the crack length and d is the offset between the crack and interface). The same phenomenon was also verified for the edge cracks. Specifically, when the offset, d, was reduced to zero, the maximum stress intensity factor value, $K_{{\theta}{\theta}}^{max}$, approached that of an artificial interface edge crack.

• Bulletin of the Korean Chemical Society
• /
• 제33권10호
• /
• pp.3258-3264
• /
• 2012

Aluminum oxide ($Al_2O_3$) nanofibers were treated thermally under an ammonia ($NH_3$) gas stream balanced by nitrogen to form a thin aluminum nitride (AlN) layer on the nanofibers, resulting in the enhancement of thermal conductivity of $Al_2O_3$/epoxy nanocomposites. The micro-structural and morphological properties of the $NH_3$-assisted thermally-treated $Al_2O_3$ nanofibers were characterized by X-ray diffraction (XRD) and atomic force microscopy (AEM), respectively. The surface characteristics and pore structures were observed by X-ray photoelectron spectroscopy (XPS), Zeta-potential and $N_2$/77 K isothermal adsorptions. From the results, the formation of AlN on $Al_2O_3$ nanofibers was confirmed by XRD and XPS. The thermal conductivity (TC) of the modified $Al_2O_3$ nanofibers/epoxy composites increased with increasing treated temperatures. On the other hand, the severely treated $Al_2O_3$/epoxy composites showed a decrease in TC, resulting from a decrease in the probability of heat-transfer networks between the filler and matrix in this system due to the aggregation of nanofiber fillers.

• 폴리머
• /
• 제39권1호
• /
• pp.46-55
• /
• 2015

There is a limit for deforestation in order to keep the environmental cycle undisturbed. The heart of the paper is to replace the wood to a maximum extent to obtain a sustainable environment. This research aims at new natural composites in which treated hemp fiber used as reinforcement, synthetic cellulose used as particulate to improve the adhesion between matrix - fiber interface and Epoxy LY556 acted as matrix fabricated by hand layup technique. The density, water absorption, tensile properties, impact strength, hardness, flexural properties and compressive properties have been evaluated under ASTM standards and compare the results with existing materials such as wood, aluminium, etc., The composite hemp fiber reinforced polymer (HFRP) could be exploited as an effective replacement for wood and it would be suitable for automotive applications by comparing results.

• 대한기계학회논문집A
• /
• 제30권12호
• /
• pp.1603-1610
• /
• 2006

In this paper compressive characteristics of composite egg-box panels were investigated and energy absorption was calculated from the nominal stress-strain relations obtained by the compressive tests. Several different stacking sequences and number of plies were introduced for investigation of static compression characteristics and the energy absorption rates of composite egg-box panels. The compressive stress-strain relation and energy absorption of various composite egg-box panels were compared with those of aluminium egg-box panels. From the test results it was found that the fracture behavior of composite egg-box panel was affected by stacking angle causing different local deformation, during lay-up and draping processes and types of prepreg; that is, plain weave carbon/epoxy and 4-harness satin glass/epoxy. The energy absorption capacity of composite egg-box panels were proved to be higher than that of aluminium egg-box panels with low mass.

• 대한금속재료학회지
• /
• 제48권6호
• /
• pp.514-522
• /
• 2010

Graphite epoxy composite material (GECM) shows high specific strength and its application in the aerospace industry is gradually increasing. However, its application would induce galvanic corrosion between GECM and metallic materials. This work focused on the effects of anodizing and thermal oxidation on galvanic corrosion in a 3.5% NaCl solution between GECM and aluminium and titanium. In the case of anodized aluminium, galvanic corrosion resistance to the GECM was greatly improved by the anodizing treatment regardless of area ratio. In the case of anodized titanium, the anodizing by a formation voltage of 50V increased corrosion resistance of titanium in galvanic tests. Thermal oxidation of titanium also improved corrosion resistance of Ti to GECM.

• Composites Research
• /
• 제18권6호
• /
• pp.19-25
• /
• 2005

본 논문에서는 하이브리드 복합재 틸팅차량 차체에 대한 시험적 연구를 수행하였다. 시험에 적용된 하이브리드 복합재 틸팅차량 차체는 길이가 23m이며 40mm두께의 알루미늄 하니콤 코어와 2mm의 직조된 탄소/에폭시 면재로 구성된 샌드위치 구조물이다. 하이브리드 복합재 틸팅차량 차체의 구조적 거동과 안전성을 규명하기 위해 수직하중- 차단압축하중, 비틀림하중 및 3점지지 하중조건하에서 정적인 하중시험을 수행하였다. 시험은 JIS E 7105규격에 근거하여 수행되었다. 시험을 통해 수직하중하에서 최대처짐은 최대 12.3mm이며 굽힘강성은 $0.81\times10^{14}\;kgf{\cdot}mm^2$로 도시철도차량성능기준을 만족하고 있었다. 또한 강도 측면에서도 탄소/에폭시 면재의 파단변형률의 $20\%$ 이내로 안전도를 만족하였다.

• Composites Research
• /
• 제19권1호
• /
• pp.9-14
• /
• 2006

본 연구는 KS F 2278 2003 (창호의 단열성 시험 방법)에 의하여 철도차량 및 버스의 내/외장재로 적용 가능한 카본/에폭시 스킨-알루미늄 하니콤 & 발사코어 샌드위치 판넬(두께 : 37mm), 카본/에폭시 스킨-알루미늄 하니콤 코어 샌드위치 판넬(두께 : 57mm, 단열재 포함) 및 카본/에폭시 스킨-알루미늄 하니콤 코어 샌드위치 판넬(두께 : 37mm)에 대한 열관류율 시험을 하였다. 또한 KS F2277 . 2002 (건축용 구성재의 단열성 측정방법-교정열상자법 및 보호열상자법)에 의하여 추가로 알루미늄 스킨-알류미늄 하니콤 샌드위치 판넬들 (두께 : 27mm, 35n1m)과 알루미늄 스킨-포밍 알루미늄 샌드위치 판넬 (두께27mm)에 대한 열관류율 시험을 수행하였다. 본 연구를 통해 면제와 심재사이에 열전달은 실제 단면적이 넓을수록 열관류율이 높았으며, 하이브리드형 복합재 일수록 단열성능이 우수함을 확인하였다.