• International Journal of Aeronautical and Space Sciences
• /
• v.7 no.1
• /
• pp.54-64
• /
• 2006

To augment weakly damped lag mode stability of a hingeless helicopter rotor blade in hover, piezoelectric shunt with a resistor and an inductor circuits for passive damping has been studied. A shunted piezoceramics bonded to a flexure of rotor blade converts mechanical strain energy to electrical charge energy which is dissipated through the resistor in the R-L series shunt circuit. Because the fundamental lag mode frequency of a soft-in-plane hingeless helicopter rotor blade is generally about 0.7/rev, the design frequency of the blade system with flexure sets to be so. Experimentally, the measured lag mode frequency is 0.7227/rev under the short circuit condition. Therefore the suppression mode of this passive damping vibration absorber is adjusted to 0.7227/rev. As a result of damping enhancement using passive control, the passive damper which consists of a piezoelectric material and shunt circuits has a stabilizing effect on inherently weakly damped lag mode of the rotor blades, at the optimum tuning and resistor condition.

• Journal of Broadcast Engineering
• /
• v.12 no.4
• /
• pp.360-372
• /
• 2007

We propose a fast inter-layer mode decision method by utilizing coding information of base layer upward its enhancement layer inscalable video coding (SVC), also called MPEG-4 part 10 Advanced Video Coding Amendment 3 or H.264 Scalable Extension (SE) which is being standardized. In this paper, when the motion vectors from the base layer have zero motion (0, 0) in inter-layer motion prediction or the Integer Transform coefficients of the residual between current MB and the motion compensated MB by the predicted motion vectors from the base layer are all zero, the block mode of the corresponding block to be encoded at the enhancement layer is determined to be the $16{\times}16$ mode. In addition, if the predicted mode of the MB to be encoded at the enhancement layer is not equal to the $16{\times}16$ mode, then the rate-distortion optimization is only performed on the reduced candidated modes which are same or smaller partitioned modes. Our proposed method exhibits the complexity reduction in encoding time up to 72%. Nevertheless, it shows negligible PSNR degradation and bit rate increase up to 0.25dB and 1.73%, respectively.

• Journal of Broadcast Engineering
• /
• v.12 no.5
• /
• pp.491-502
• /
• 2007

In this parer, we propose an efficient intra prediction mode decision scheme in Scalable Video Coding(SVC) which is an emerging video coding standard as an extension of H.264/MPEG-4 AVC(Advanced Video Coding). The proposed method in base on the characteristic of macroblock smoothness follows the statistical analysis of intra prediction mode in an enhancement layer and it decides a candidate intra prediction mode. We also propose an early termination scheme for Intra_BL mode decision where the RD cost value of Intra_BL is utilized. Simulation results show that the proposed method reduces 54.67% of the computation complexity of intra prediction coding, while the degradation in video quality is negligible; for low QP values, the average PSNR loss is very negligible, equivalently the bit rate increases by 0.011%. For high QP values, the average PSNR loss is less than 0.01dB, which equals to 0.249% increase in bitrate.

• The Transactions of The Korean Institute of Electrical Engineers
• /
• v.59 no.1
• /
• pp.160-167
• /
• 2010

This paper proposes an adaptive sliding mode observer (SMO), which adds the estimation function of the stator resistance to a new sliding mode observer for the robust sensorless control of permanent magnet synchronous motor (PMSM) with variable parameters. To reduce the chattering problem commonly found in the conventional sliding mode observer where the low-pass filter and additional position compensation of the rotor are used, the sigmoid function is used for the control of a switching function in this research. With the estimation of the stator resistance, the proposed observer can improve the control performance by reducing the estimation error of the motor's speed. Note that the stator resistance is varying with the ambient temperature and becomes an error source for the sensorless control of PMSM. The new sliding mode observer has better efficiency than the conventional adaptive sliding mode observer by reducing the time consuming integral calculations. The stability of the proposed adaptive sliding mode observer is verified by the Lyapunov function in determining the observer gains, and the effectiveness of the observer is demonstrated by simulations and experiments.

• Journal of Korean Ophthalmic Optics Society
• /
• v.4 no.2
• /
• pp.45-49
• /
• 1999

The second harmonic, wavelength is 397nm, of the continuous wave diode laser, whose maximum power is 35mW, was generated in $LiIO_3$ crystals in a ring enhancement cavity. 5mm- and 10mm-long crystals cut $43.21^{\circ}$ for optic axis were used in this experiment. Both surfaces of those were anti-reflection coated for 794nm. In case the crystal was inserted into the cavity, the condition of separation between two concave mirrors for the optimum mode matching was found. The conversion efficiency of second harmonic generation was increased by the resonant enhancement of pumping power in the ring enhancement cavity, and the frequency of diode laser was locked to that of the counter-propagation mode generated from the surface of crystal. When the pumping power was 28 mW, the infrared buildup factor was about 45 without the crystal, and 14 with the crystal due to the transmission loss of crystal. The maximum second harmonic powers of $1.5{\mu}W$ and $6.6{\mu}W$ were obtained, and corresponding conversion efficiencies were $(6.584{\pm}0.56){\times}10^{-3}$%, $2.6{\pm}0.21){\times}10%{-2}$% in 5mm- and 10mm-long $LiIO_3$, respectively.

• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.28 no.2
• /
• pp.146-153
• /
• 2004

A Promising new approach to achieve low pollutant emissions and improvement of flame stability is tested experimentally using a cyclone jet hybrid combustor employing both premixed and diffusion combustion mode. Three kinds of nozzle are tested for mixing enhancement of fuel and air. The LNG (Liquified Natural Gas) is used as a fuel. The combustor is operated by two methods. One is DC (Diffusion Combustion) mode generated swirl flow by air as general swirl combustor, and the other is HC (Hybrid Combustion) mode. The HC mode consists of diffusion jet flame of axial direction and premixed cyclone flame of tangential direction in order to stabilized the diffusion jet flame. The results showed that the flame stability of HC mode is significantly enhanced than that of DC mode through the change of mixing characteristics by modifications of fuel nozzle. In addition, the reductions of CO and NOx emission in HC mode, as compared with that for the DC mode, is large than about 50% in stable region. Also, even using the low calorific fuel as $CO_2$-blended gas, it is identified that the cyclone jet hybrid combustor has the high performance of flame stability.

• Journal of the Korean Institute of Telematics and Electronics D
• /
• v.36D no.3
• /
• pp.75-84
• /
• 1999

Systematic studies for the effect of the linewidth enhancement factor, the confinement factor, the internal loss and the cavity length on the single mode gain difference and the frequency detuning are performed for $\lambda$/4 phase shifted DFB lasers above threshold. The above threshold characteristics are mainly determined by the linewidth enhancement factor, not by the confinement factor or the parameter defined by the product of the linewidth enhancement factor and the confinement factor. The normalized internal loss defined by the product of the internal loss and the cavity length mainly determines the above threshold characteristics compared to that of the internal loss or the cavity length alone. The effect of the cavity length on threshold characteristics is larger than that of the internal loss in the case of the same normalized internal loss. The above threshold characteristics of quantum well lasers are more resistant to the variations of the confinement factor and the normalized internal loss than those of bulk lasers due to the small linewidth enhancement factor.

• STI Policy Review
• /
• v.8 no.2
• /
• pp.23-48
• /
• 2017

This article advocates for a Mode 3 science policy. Compared to the university research-based Mode 1 knowledge production system and the knowledge application-centric Mode 2 innovation system, Mode 3 can be defined as a system that integrates both Mode 1 and Mode 2-type knowledge production models. In this article, based on the major characteristics of the Mode 3 scientific knowledge production system, I agree with the advocates of Mode 3 that constructing a knowledge society requires an inclusive form of knowledge production and innovation system through the democratization of knowledge production as well as the promotion of social values. Moreover, the mechanisms for creating accountable innovation in the Mode 3 system should be given more attention from the science research and policy communities to make public policy for scientific and technological innovation more reflective of social changes. Similar to the ways that the Mode 1 and Mode 2 scientific knowledge production approaches have influenced the development of science policy models, the Mode 3 scientific knowledge production approach, or Mode 3 science, also has the potential to shape a new science policy model. I will refer to this as Mode 3 science policy. In an effort to conceptualize the democracy- and society-centric Mode 3 science policy model, I will articulate science policy strategies in four science policy domains in South Korea from the context of the Mode 3 science approach. These include (1) evaluation of publicly-funded research activities, (2) valorization of scientific knowledge (that is, enhancement of the value of scientific knowledge through governmental action), (3) development of a science policy decision-making support system, and (4) anticipatory foresight of science, technology and society. When adopting and implementing a Mode 3 science framework, one progressive change is to increase socially desirable innovation such as responsible innovation.

• Proceedings of the IEEK Conference
• /
• 1998.10a
• /
• pp.1077-1080
• /
• 1998

In this paper, a simple low-power current-mode CMOS wotage reference circuit is proposed. The reference circuit of enhancement-mode MOS transistors and resistors. Temperature compensation is made by adding a current component proportional to a thermal voltage to a current component proportional to a threshold voltage. The designed circuit has been simulated using a $0.65\mu\textrm{m}$ n-well CMOS process parameters. The simulation results show that the reference circuit has a temperature coefficient less than $7.8ppm/^{\circ}C$ and a power-supply(VDD) coefficient less than 0.079%/V for a temperature range from $-30^{\circ}C$ to $130^{\circ}C$ and a VDD range from 4.0V to 12V. The power consumption is 105㎼ for VDD=5V and $T=30^{\circ}C.$ The proposed reference circuit can be designed to generate a wide range of reference voltages owing to its current-mode operation.

• Proceedings of the Korean Society of Broadcast Engineers Conference
• /
• 2016.06a
• /
• pp.264-266
• /
• 2016

During the $2^{nd}$ JVET (Joint Group on Future Video Coding Technology Exploration) meeting, up to 22 coding tools focusing on Future Video Coding (FVC) were proposed. Despite that the application of proposed coding tools has a considerable performance enhancement, however, the encoding time of Joint Exploration Model (JEM) software is over 20 times for All Intra coding mode, 6 times for Random Access coding mode, of HEVC reference model (HM), and decoding time is 1.6 times for All Intra coding mode, 7.9 times for Random Access coding mode, of HM. This paper focuses on analyzing the complexity of the JEM software compared with HM.